182 lines
3.9 KiB
Plaintext
182 lines
3.9 KiB
Plaintext
# Kconfig - SPI driver configuration options
|
|
|
|
#
|
|
# Copyright (c) 2015-2016 Intel Corporation
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
#
|
|
# SPI Drivers
|
|
#
|
|
menuconfig SPI
|
|
bool
|
|
prompt "SPI hardware bus support"
|
|
default n
|
|
help
|
|
Enable support for the SPI hardware bus.
|
|
|
|
config SPI_QMSI
|
|
bool "QMSI driver for SPI controller"
|
|
depends on SPI && QMSI
|
|
default n
|
|
help
|
|
SPI driver implementation using QMSI library. QMSI is the
|
|
Quark Microcontroller Software Interface, providing a common
|
|
interface to the Quark family of microcontrollers.
|
|
|
|
config SPI_QMSI_SS
|
|
bool "QMSI driver for SPI controller on Sensor Subsystem"
|
|
depends on SPI && QMSI
|
|
default n
|
|
help
|
|
SPI driver implementation using QMSI library. This instance is
|
|
for the Sensor Subsystem.
|
|
|
|
config SPI_K64
|
|
bool
|
|
prompt "Freescale K64-based SPI controller driver"
|
|
depends on SPI && SOC_MK64F12
|
|
default n
|
|
help
|
|
Enable support for Freescale K64-based SPI controllers.
|
|
|
|
config SPI_INTEL
|
|
bool
|
|
prompt "Intel SPI controller driver"
|
|
depends on SPI && CPU_MINUTEIA
|
|
default n
|
|
help
|
|
Enable support for Intel's SPI controllers. Such controller
|
|
was formelly found on XScale chips. It can be found nowadays
|
|
on CEXXXX Intel media controller and Quark CPU (2 of them).
|
|
|
|
|
|
if SPI
|
|
config SPI_INIT_PRIORITY
|
|
int "Init priority"
|
|
default 70
|
|
help
|
|
Device driver initialization priority.
|
|
|
|
config SYS_LOG_SPI_LEVEL
|
|
int
|
|
prompt "SPI Driver Log level"
|
|
depends on SYS_LOG && SPI
|
|
default 0
|
|
range 0 4
|
|
help
|
|
Sets log level for SPI drivers.
|
|
Levels are:
|
|
0 OFF, do not write
|
|
1 ERROR, only write SYS_LOG_ERR
|
|
2 WARNING, write SYS_LOG_WRN in adition to previous level
|
|
3 INFO, write SYS_LOG_INF in adition to previous levels
|
|
4 DEBUG, write SYS_LOG_DBG in adition to previous levels
|
|
|
|
config SPI_CS_GPIO
|
|
bool "SPI port CS pin is controlled via a GPIO port"
|
|
depends on GPIO
|
|
default n
|
|
|
|
config SPI_0
|
|
bool
|
|
prompt "SPI port 0"
|
|
default n
|
|
help
|
|
Enable SPI controller port 0.
|
|
|
|
config SPI_0_NAME
|
|
string
|
|
prompt "SPI port 0 device name"
|
|
depends on SPI_0
|
|
default "SPI_0"
|
|
|
|
config SPI_0_IRQ_PRI
|
|
int
|
|
prompt "Port 0 interrupt priority"
|
|
depends on SPI_0
|
|
|
|
config SPI_0_CS_GPIO_PORT
|
|
string
|
|
prompt "The GPIO port which is used to control CS"
|
|
depends on SPI_0 && SPI_CS_GPIO
|
|
default "GPIO_0"
|
|
|
|
config SPI_0_CS_GPIO_PIN
|
|
int "The GPIO PIN which is used to act as a CS pin"
|
|
depends on SPI_0 && SPI_CS_GPIO
|
|
default 0
|
|
|
|
config SPI_1
|
|
bool
|
|
prompt "SPI port 1"
|
|
default n
|
|
help
|
|
Enable SPI controller port 1.
|
|
|
|
config SPI_1_NAME
|
|
string
|
|
prompt "SPI port 1 device name"
|
|
depends on SPI_1
|
|
default "SPI_1"
|
|
|
|
config SPI_1_IRQ_PRI
|
|
int
|
|
prompt "Port 0 interrupt priority"
|
|
depends on SPI_1
|
|
|
|
config SPI_1_CS_GPIO_PORT
|
|
string
|
|
prompt "The GPIO port which is used to control CS"
|
|
depends on SPI_1 && SPI_CS_GPIO
|
|
default "GPIO_0"
|
|
|
|
config SPI_1_CS_GPIO_PIN
|
|
int "The GPIO PIN which is used to act as a CS pin"
|
|
depends on SPI_1 && SPI_CS_GPIO
|
|
default 0
|
|
|
|
config SPI_2
|
|
bool
|
|
prompt "SPI port 2"
|
|
default n
|
|
help
|
|
Enable SPI controller port 2.
|
|
|
|
config SPI_2_NAME
|
|
string
|
|
prompt "SPI port 2 device name"
|
|
depends on SPI_2
|
|
default "SPI_2"
|
|
|
|
config SPI_2_IRQ_PRI
|
|
int
|
|
prompt "Port 2 interrupt priority"
|
|
depends on SPI_2
|
|
|
|
config SPI_2_CS_GPIO_PORT
|
|
string
|
|
prompt "The GPIO port which is used to control CS"
|
|
depends on SPI_2 && SPI_CS_GPIO
|
|
default "GPIO_0"
|
|
|
|
config SPI_2_CS_GPIO_PIN
|
|
int "The GPIO PIN which is used to act as a CS pin"
|
|
depends on SPI_2 && SPI_CS_GPIO
|
|
default 0
|
|
|
|
source "drivers/spi/Kconfig.dw"
|
|
|
|
endif # SPI
|