113 lines
3.7 KiB
Plaintext
113 lines
3.7 KiB
Plaintext
# TI CC13xx / CC26xx IEEE 802.15.4 configuration options
|
|
|
|
# Copyright (c) 2019 Brett Witherspoon
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
menuconfig IEEE802154_CC13XX_CC26XX
|
|
bool "TI CC13xx / CC26xx IEEE 802.15.4 driver support"
|
|
select CRC
|
|
default y
|
|
depends on DT_HAS_TI_CC13XX_CC26XX_IEEE802154_ENABLED
|
|
|
|
if IEEE802154_CC13XX_CC26XX
|
|
|
|
config IEEE802154_CC13XX_CC26XX_INIT_PRIO
|
|
int "TI CC13xx / CC26xx IEEE 802.15.4 initialization priority"
|
|
default 80
|
|
help
|
|
Set the initialization priority number.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_RADIO_TX_RETRIES
|
|
int "Radio Transmission attempts"
|
|
default NET_L2_IEEE802154_RADIO_TX_RETRIES if NET_L2_IEEE802154
|
|
default 3
|
|
range 1 7
|
|
help
|
|
Number of transmission attempts radio driver should do, before
|
|
replying it could not send the packet.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_RADIO_CSMA_CA_MAX_BO
|
|
int "CSMA maximum backoffs"
|
|
default NET_L2_IEEE802154_RADIO_CSMA_CA_MAX_BO if NET_L2_IEEE802154_RADIO_CSMA_CA
|
|
default 4
|
|
range 1 5
|
|
help
|
|
The maximum number of backoffs the CSMA-CA algorithm will attempt
|
|
before declaring a channel access failure.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_RADIO_CSMA_CA_MIN_BE
|
|
int "CSMA MAC minimum backoff exponent"
|
|
default NET_L2_IEEE802154_RADIO_CSMA_CA_MIN_BE if NET_L2_IEEE802154_RADIO_CSMA_CA
|
|
default 3
|
|
range 1 8
|
|
help
|
|
The minimum value of the backoff exponent (BE) in the CSMA-CA
|
|
algorithm.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_RADIO_CSMA_CA_MAX_BE
|
|
int "CSMA MAC maximum backoff exponent"
|
|
default NET_L2_IEEE802154_RADIO_CSMA_CA_MAX_BE if NET_L2_IEEE802154_RADIO_CSMA_CA
|
|
default 5
|
|
range 1 8
|
|
help
|
|
The maximum value of the backoff exponent (BE) in the CSMA-CA
|
|
algorithm.
|
|
|
|
endif # IEEE802154_CC13XX_CC26XX
|
|
|
|
menuconfig IEEE802154_CC13XX_CC26XX_SUB_GHZ
|
|
bool "TI CC13xx / CC26xx IEEE 802.15.4g driver support"
|
|
default y
|
|
depends on DT_HAS_TI_CC13XX_CC26XX_IEEE802154_SUBGHZ_ENABLED
|
|
|
|
if IEEE802154_CC13XX_CC26XX_SUB_GHZ
|
|
|
|
config IEEE802154_CC13XX_CC26XX_SUB_GHZ_NUM_RX_BUF
|
|
int "TI CC13xx / CC26xx IEEE 802.15.4g receive buffer count"
|
|
default 2
|
|
help
|
|
This option allows the user to configure the number of
|
|
receive buffers.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_SUB_GHZ_CS_THRESHOLD
|
|
int "TI CC13xx / CC26xx IEEE 802.15.4g Carrier Sense ED Threshold in dBm"
|
|
default -80 # Based on SUN FSK, 200 kHz bit rate, no FEC, see IEEE 802.15.4-2020, section 19.6.7
|
|
help
|
|
This option sets the energy detection (ED) threshold for
|
|
clear channel assessment (CCA) modes 1 or 3 in the CSMA/CA
|
|
algorithm. Except for the SUN O-QPSK PHY, the ED threshold
|
|
shall correspond to a received signal power of at most 10 dB
|
|
greater than the specified receiver sensitivity for that PHY,
|
|
or in accordance with local regulations (see IEEE 802.15.4-2020,
|
|
section 10.2.8). For the SUN O-QPSK PHY, the ED threshold shall
|
|
comply with IEEE 802.15.4-2020, section 21.5.13.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_SUB_GHZ_INIT_PRIO
|
|
int "TI CC13xx / CC26xx IEEE 802.15.4g initialization priority"
|
|
default 80
|
|
help
|
|
Set the initialization priority number.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_SUB_GHZ_RADIO_TX_RETRIES
|
|
bool
|
|
select DEPRECATED
|
|
help
|
|
DEPRECATED - use NET_L2_IEEE802154_RADIO_TX_RETRIES instead
|
|
|
|
config IEEE802154_CC13XX_CC26XX_SUB_GHZ_CUSTOM_RADIO_SETUP
|
|
bool "Use custom radio setup structures (advanced)"
|
|
default n
|
|
help
|
|
Imports the radio setup structure from an external module instead of using
|
|
the default one.
|
|
Allows overriding the RF modulation / protocol settings.
|
|
|
|
config IEEE802154_CC13XX_CC26XX_SUB_GHZ_CUSTOM_POWER_TABLE
|
|
bool "Use custom power table structure (advanced)"
|
|
default n
|
|
help
|
|
Imports the radio power table from an external module.
|
|
Allows overriding the RF modulation settings.
|
|
|
|
endif # IEEE802154_CC13XX_CC26XX_SUB_GHZ
|