94 lines
2.1 KiB
Plaintext
94 lines
2.1 KiB
Plaintext
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
menuconfig LPS25HB
|
|
bool
|
|
prompt "LPS25HB pressure and temperature"
|
|
depends on SENSOR && I2C
|
|
default n
|
|
help
|
|
Enable driver for LPS25HB I2C-based pressure and temperature
|
|
sensor.
|
|
|
|
config LPS25HB_SYS_LOG_LEVEL
|
|
int "LPS25HB Log level"
|
|
depends on SYS_LOG && LPS25HB
|
|
default 0
|
|
range 0 4
|
|
help
|
|
Sets log level for LPS25HB driver.
|
|
|
|
Levels are:
|
|
|
|
- 0 OFF: do not write
|
|
|
|
- 1 ERROR: only write SYS_LOG_ERR
|
|
|
|
- 2 WARNING: write SYS_LOG_WRN in addition to previous level
|
|
|
|
- 3 INFO: write SYS_LOG_INF in addition to previous levels
|
|
|
|
- 4 DEBUG: write SYS_LOG_DBG in addition to previous levels
|
|
|
|
config LPS25HB_DEV_NAME
|
|
string
|
|
prompt "Device name"
|
|
default "lps25hb"
|
|
depends on LPS25HB
|
|
help
|
|
Device name with which the LPS25HB sensor is identified.
|
|
|
|
config LPS25HB_INIT_PRIORITY
|
|
int
|
|
prompt "Init priority"
|
|
depends on LPS25HB
|
|
default 70
|
|
help
|
|
Device driver initialization priority.
|
|
|
|
config LPS25HB_I2C_ADDR
|
|
hex
|
|
prompt "I2C address"
|
|
depends on LPS25HB
|
|
default "0x5C"
|
|
help
|
|
I2C address of the LPS25HB sensor.
|
|
Use 0x5C if the SA0 pin is pulled to GND or 0x5D if the SA0
|
|
pin is pulled to VDD.
|
|
|
|
config LPS25HB_I2C_MASTER_DEV_NAME
|
|
string
|
|
prompt "I2C master where LPS25HB is connected"
|
|
depends on LPS25HB
|
|
default "I2C_0"
|
|
help
|
|
Specify the device name of the I2C master device to which
|
|
LPS25HB is connected.
|
|
|
|
menu "Attributes"
|
|
depends on LPS25HB
|
|
|
|
config LPS25HB_SAMPLING_RATE
|
|
int
|
|
prompt "Output data rate"
|
|
depends on LPS25HB
|
|
default 25
|
|
help
|
|
Sensor output data rate expressed in samples per second.
|
|
Data rates supported by the chip are 1, 7, 13, 25.
|
|
|
|
endmenu
|