151 lines
3.4 KiB
Plaintext
151 lines
3.4 KiB
Plaintext
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
menuconfig HMC5883L
|
|
bool
|
|
prompt "HMC5883L magnetometer"
|
|
depends on SENSOR && I2C
|
|
default n
|
|
help
|
|
Enable driver for HMC5883L I2C-based magnetometer.
|
|
|
|
config HMC5883L_SYS_LOG_LEVEL
|
|
int "HMC5883L Log level"
|
|
depends on SYS_LOG && HMC5883L
|
|
default 0
|
|
range 0 4
|
|
help
|
|
Sets log level for HMC5883L driver.
|
|
Levels are:
|
|
|
|
- 0 OFF: do not write
|
|
|
|
- 1 ERROR: only write SYS_LOG_ERR
|
|
|
|
- 2 WARNING: write SYS_LOG_WRN in addition to previous level
|
|
|
|
- 3 INFO: write SYS_LOG_INF in addition to previous levels
|
|
|
|
- 4 DEBUG: write SYS_LOG_DBG in addition to previous levels
|
|
|
|
config HMC5883L_NAME
|
|
string
|
|
prompt "Driver name"
|
|
default "HMC5883L"
|
|
depends on HMC5883L
|
|
help
|
|
Device name with which the HMC5883L sensor is identified.
|
|
|
|
config HMC5883L_INIT_PRIORITY
|
|
int
|
|
prompt "Init priority"
|
|
depends on HMC5883L
|
|
default 70
|
|
help
|
|
Device driver initialization priority.
|
|
|
|
config HMC5883L_I2C_MASTER_DEV_NAME
|
|
string
|
|
prompt "I2C master where HMC5883L is connected"
|
|
depends on HMC5883L
|
|
default "I2C_0"
|
|
help
|
|
Specify the device name of the I2C master device to which HMC5883L
|
|
is connected.
|
|
|
|
choice
|
|
prompt "Trigger mode"
|
|
depends on HMC5883L
|
|
default HMC5883L_TRIGGER_GLOBAL_FIBER
|
|
help
|
|
Specify the type of triggering to be used by the driver.
|
|
|
|
config HMC5883L_TRIGGER_NONE
|
|
bool
|
|
prompt "No trigger"
|
|
|
|
config HMC5883L_TRIGGER_GLOBAL_FIBER
|
|
bool
|
|
prompt "Use global fiber"
|
|
depends on GPIO && SYSTEM_WORKQUEUE
|
|
select HMC5883L_TRIGGER
|
|
|
|
config HMC5883L_TRIGGER_OWN_FIBER
|
|
bool
|
|
prompt "Use own fiber"
|
|
depends on GPIO
|
|
select HMC5883L_TRIGGER
|
|
|
|
endchoice
|
|
|
|
config HMC5883L_TRIGGER
|
|
bool
|
|
depends on HMC5883L
|
|
|
|
config HMC5883L_GPIO_DEV_NAME
|
|
string
|
|
prompt "GPIO device"
|
|
default "GPIO_0"
|
|
depends on HMC5883L && HMC5883L_TRIGGER
|
|
help
|
|
The device name of the GPIO device to which the HMC5883L interrupt
|
|
pin is connected.
|
|
|
|
config HMC5883L_GPIO_PIN_NUM
|
|
int
|
|
prompt "Interrupt GPIO pin number"
|
|
default 0
|
|
depends on HMC5883L && HMC5883L_TRIGGER
|
|
help
|
|
The number of the GPIO on which the interrupt signal from the
|
|
HMC5883L chip will be received.
|
|
|
|
config HMC5883L_FIBER_PRIORITY
|
|
int
|
|
prompt "Fiber priority"
|
|
depends on HMC5883L && HMC5883L_TRIGGER_OWN_FIBER
|
|
default 10
|
|
help
|
|
Priority of fiber used by the driver to handle interrupts.
|
|
|
|
config HMC5883L_FIBER_STACK_SIZE
|
|
int
|
|
prompt "Fiber stack size"
|
|
depends on HMC5883L && HMC5883L_TRIGGER_OWN_FIBER
|
|
default 1024
|
|
help
|
|
Stack size of fiber used by the driver to handle interrupts.
|
|
|
|
config HMC5883L_ODR
|
|
string
|
|
prompt "Output data rate"
|
|
depends on HMC5883L
|
|
default "15"
|
|
help
|
|
Magnetometer output data rate expressed in samples per second.
|
|
Data rates supported by the chip are 0.75, 1.5, 3, 7.5, 15, 30
|
|
and 75.
|
|
|
|
config HMC5883L_FS
|
|
string
|
|
prompt "Full-scale range"
|
|
depends on HMC5883L
|
|
default "1.3"
|
|
help
|
|
Magnetometer full-scale range.
|
|
An X value for the config represents a range of +/- X gauss. Valid
|
|
values are 0.88, 1.3, 1.9, 2.5, 4, 4.7, 5.6 and 8.1.
|