79 lines
3.0 KiB
Plaintext
79 lines
3.0 KiB
Plaintext
Title: Shared Floating Point Support
|
|
|
|
Description:
|
|
|
|
The Shared Floating Point Support test uses two tasks to:
|
|
|
|
1) load and store floating point registers and check for corruption
|
|
2) independently compute pi and check for any errors
|
|
|
|
This tests the ability of tasks to safely share floating point hardware
|
|
resources, even when switching occurs preemptively (note that both sets of
|
|
tests run concurrently even though they report their progress at different
|
|
times).
|
|
|
|
The demonstration utilizes semaphores, round robin scheduling, and floating
|
|
point support.
|
|
|
|
--------------------------------------------------------------------------------
|
|
|
|
Building and Running Project:
|
|
|
|
This project outputs to the console. It can be built and executed
|
|
on QEMU as follows:
|
|
|
|
make run
|
|
|
|
--------------------------------------------------------------------------------
|
|
|
|
Troubleshooting:
|
|
|
|
Problems caused by out-dated project information can be addressed by
|
|
issuing one of the following commands then rebuilding the project:
|
|
|
|
make clean # discard results of previous builds
|
|
# but keep existing configuration info
|
|
or
|
|
make pristine # discard results of previous builds
|
|
# and restore pre-defined configuration info
|
|
|
|
--------------------------------------------------------------------------------
|
|
|
|
Advanced:
|
|
|
|
Depending upon the board's speed, the frequency of test output may range from
|
|
every few seconds to every few minutes. The speed of the test can be controlled
|
|
through the variable PI_NUM_ITERATIONS (default 700000). Lowering this value
|
|
will increase the test's speed, but at the expense of the calculation's
|
|
precision.
|
|
|
|
make run PI_NUM_ITERATIONS=100000
|
|
|
|
--------------------------------------------------------------------------------
|
|
|
|
Sample Output:
|
|
|
|
*** Booting Zephyr OS build zephyr-v2.2.0-845-g8b769de30317 ***
|
|
Running test suite fp_sharing
|
|
===================================================================
|
|
starting test - test_load_store
|
|
Load and store OK after 0 (high) + 63 (low) tests
|
|
Load and store OK after 100 (high) + 6540 (low) tests
|
|
Load and store OK after 200 (high) + 12965 (low) tests
|
|
Load and store OK after 300 (high) + 19366 (low) tests
|
|
Load and store OK after 400 (high) + 25756 (low) tests
|
|
Load and store OK after 500 (high) + 32128 (low) tests
|
|
PASS - test_load_store
|
|
===================================================================
|
|
starting test - test_pi
|
|
Pi calculation OK after 50 (high) + 10 (low) tests (computed 3.141598)
|
|
Pi calculation OK after 150 (high) + 31 (low) tests (computed 3.141598)
|
|
Pi calculation OK after 250 (high) + 51 (low) tests (computed 3.141598)
|
|
Pi calculation OK after 350 (high) + 72 (low) tests (computed 3.141598)
|
|
Pi calculation OK after 450 (high) + 92 (low) tests (computed 3.141598)
|
|
PASS - test_pi
|
|
===================================================================
|
|
Test suite fp_sharing succeeded
|
|
===================================================================
|
|
PROJECT EXECUTION SUCCESSFUL
|