117 lines
3.2 KiB
C
117 lines
3.2 KiB
C
/*
|
|
* Copyright (c) 2018 Phytec Messtechnik GmbH
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
|
|
#ifndef __SSD1306_REGS_H__
|
|
#define __SSD1306_REGS_H__
|
|
|
|
/* All following bytes will contain commands */
|
|
#define SSD1306_CONTROL_ALL_BYTES_CMD 0x00
|
|
/* All following bytes will contain data */
|
|
#define SSD1306_CONTROL_ALL_BYTES_DATA 0x40
|
|
/* The next byte will contain a command */
|
|
#define SSD1306_CONTROL_BYTE_CMD 0x80
|
|
/* The next byte will contain data */
|
|
#define SSD1306_CONTROL_BYTE_DATA 0xc0
|
|
#define SSD1306_READ_STATUS_MASK 0xc0
|
|
#define SSD1306_READ_STATUS_BUSY 0x80
|
|
#define SSD1306_READ_STATUS_ON 0x40
|
|
|
|
/*
|
|
* Fundamental Command Table
|
|
*/
|
|
#define SSD1306_SET_CONTRAST_CTRL 0x81 /* double byte command */
|
|
|
|
#define SSD1306_SET_ENTIRE_DISPLAY_OFF 0xa4
|
|
#define SSD1306_SET_ENTIRE_DISPLAY_ON 0xa5
|
|
|
|
#define SSD1306_SET_NORMAL_DISPLAY 0xa6
|
|
#define SSD1306_SET_REVERSE_DISPLAY 0xa7
|
|
|
|
#define SSD1306_DISPLAY_OFF 0xae
|
|
#define SSD1306_DISPLAY_ON 0xaf
|
|
|
|
/*
|
|
* Addressing Setting Command Table
|
|
*/
|
|
#define SSD1306_SET_LOWER_COL_ADDRESS 0x00
|
|
#define SSD1306_SET_LOWER_COL_ADDRESS_MASK 0x0f
|
|
|
|
#define SSD1306_SET_HIGHER_COL_ADDRESS 0x10
|
|
#define SSD1306_SET_HIGHER_COL_ADDRESS_MASK 0x0f
|
|
|
|
#define SSD1306_SET_MEM_ADDRESSING_MODE 0x20 /* double byte command */
|
|
#define SSD1306_SET_MEM_ADDRESSING_HORIZONTAL 0x00
|
|
#define SSD1306_SET_MEM_ADDRESSING_VERTICAL 0x01
|
|
#define SSD1306_SET_MEM_ADDRESSING_PAGE 0x02
|
|
|
|
#define SSD1306_SET_COLUMN_ADDRESS 0x21 /* triple byte command */
|
|
|
|
#define SSD1306_SET_PAGE_ADDRESS 0x22 /* triple byte command */
|
|
|
|
#define SSD1306_SET_PAGE_START_ADDRESS 0xb0
|
|
#define SSD1306_SET_PAGE_START_ADDRESS_MASK 0x07
|
|
|
|
|
|
/*
|
|
* Hardware Configuration Command Table
|
|
*/
|
|
#define SSD1306_SET_START_LINE 0x40
|
|
#define SSD1306_SET_START_LINE_MASK 0x3f
|
|
|
|
#define SSD1306_SET_SEGMENT_MAP_NORMAL 0xa0
|
|
#define SSD1306_SET_SEGMENT_MAP_REMAPED 0xa1
|
|
|
|
#define SSD1306_SET_MULTIPLEX_RATIO 0xa8 /* double byte command */
|
|
|
|
#define SSD1306_SET_COM_OUTPUT_SCAN_NORMAL 0xc0
|
|
#define SSD1306_SET_COM_OUTPUT_SCAN_FLIPPED 0xc8
|
|
|
|
#define SSD1306_SET_DISPLAY_OFFSET 0xd3 /* double byte command */
|
|
|
|
#define SSD1306_SET_PADS_HW_CONFIG 0xda /* double byte command */
|
|
#define SSD1306_SET_PADS_HW_SEQUENTIAL 0x02
|
|
#define SSD1306_SET_PADS_HW_ALTERNATIVE 0x12
|
|
|
|
|
|
/*
|
|
* Timming and Driving Scheme Setting Command Table
|
|
*/
|
|
#define SSD1306_SET_CLOCK_DIV_RATIO 0xd5 /* double byte command */
|
|
|
|
#define SSD1306_SET_CHARGE_PERIOD 0xd9 /* double byte command */
|
|
|
|
#define SSD1306_SET_VCOM_DESELECT_LEVEL 0xdb /* double byte command */
|
|
|
|
#define SSD1306_NOP 0xe3
|
|
|
|
/*
|
|
* Charge Pump Command Table
|
|
*/
|
|
#define SSD1306_SET_CHARGE_PUMP_ON 0x8d /* double byte command */
|
|
#define SSD1306_SET_CHARGE_PUMP_ON_DISABLED 0x10
|
|
#define SSD1306_SET_CHARGE_PUMP_ON_ENABLED 0x14
|
|
|
|
#define SH1106_SET_DCDC_MODE 0xad /* double byte command */
|
|
#define SH1106_SET_DCDC_DISABLED 0x8a
|
|
#define SH1106_SET_DCDC_ENABLED 0x8b
|
|
|
|
#define SSD1306_SET_PUMP_VOLTAGE_64 0x30
|
|
#define SSD1306_SET_PUMP_VOLTAGE_74 0x31
|
|
#define SSD1306_SET_PUMP_VOLTAGE_80 0x32
|
|
#define SSD1306_SET_PUMP_VOLTAGE_90 0x33
|
|
|
|
/*
|
|
* Read modify write
|
|
*/
|
|
#define SSD1306_READ_MODIFY_WRITE_START 0xe0
|
|
#define SSD1306_READ_MODIFY_WRITE_END 0xee
|
|
|
|
/* time constants in ms */
|
|
#define SSD1306_RESET_DELAY 1
|
|
|
|
#endif
|