131 lines
2.0 KiB
Plaintext
131 lines
2.0 KiB
Plaintext
/*
|
|
* Copyright (c) 2017, NXP
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include <nxp/nxp_rt.dtsi>
|
|
|
|
/ {
|
|
model = "NXP MIMXRT1050-EVK board";
|
|
compatible = "nxp,mimxrt1052";
|
|
|
|
aliases {
|
|
gpio-1= &gpio1;
|
|
gpio-2= &gpio2;
|
|
gpio-3= &gpio3;
|
|
gpio-4= &gpio4;
|
|
gpio-5= &gpio5;
|
|
i2c-1 = &i2c1;
|
|
uart-1 = &uart1;
|
|
uart-3 = &uart3;
|
|
led0 = &green_led;
|
|
sw0 = &user_button;
|
|
spi-3 = &spi3;
|
|
eth = ð
|
|
};
|
|
|
|
chosen {
|
|
zephyr,console = &uart1;
|
|
zephyr,shell-uart = &uart1;
|
|
};
|
|
|
|
sdram0: memory@80000000 {
|
|
/* Micron MT48LC16M16A2B4-6AIT:G */
|
|
device_type = "memory";
|
|
compatible = "mmio-sram";
|
|
reg = <0x80000000 0x2000000>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
green_led: led_0 {
|
|
gpios = <&gpio1 9 0>;
|
|
label = "User LD1";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button_0 {
|
|
label = "User SW8";
|
|
gpios = <&gpio5 0 GPIO_INT_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
panel {
|
|
compatible = "rocktech,rk043fn02h-ct";
|
|
port {
|
|
lcd_panel_in: endpoint {
|
|
remote-endpoint = <&lcd_panel_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
arduino_serial: &uart3 {};
|
|
|
|
&flexspi0 {
|
|
reg = <0x402a8000 0x4000>, <0x60000000 0x4000000>;
|
|
hyperflash0: hyperflash@0 {
|
|
compatible = "cypress,s26ks512s";
|
|
reg = <0>;
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&lcdif1 {
|
|
status = "okay";
|
|
port {
|
|
lcd_panel_out: endpoint {
|
|
remote-endpoint = <&lcd_panel_in>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
status = "okay";
|
|
|
|
fxos8700@1f {
|
|
compatible = "nxp,fxos8700";
|
|
reg = <0x1f>;
|
|
label = "FXOS8700";
|
|
|
|
/* Two zero ohm resistors (R263 and R264) isolate sensor
|
|
* interrupt gpios from the soc and are unpopulated by default.
|
|
* Note that if you populate them, they conflict with LCD and
|
|
* Ethernet interrupt gpios.
|
|
*/
|
|
int1-gpios = <&gpio1 10 0>;
|
|
int2-gpios = <&gpio1 11 0>;
|
|
};
|
|
};
|
|
|
|
&uart1 {
|
|
status = "okay";
|
|
current-speed = <115200>;
|
|
};
|
|
|
|
&spi3 {
|
|
status = "okay";
|
|
};
|
|
|
|
ð {
|
|
status = "okay";
|
|
ptp {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&usbd1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usdhc1 {
|
|
status = "okay";
|
|
pwr-gpios = <&gpio1 5 0>;
|
|
cd-gpios = <&gpio2 28 0>;
|
|
};
|