134 lines
3.9 KiB
ReStructuredText
134 lines
3.9 KiB
ReStructuredText
.. _ArgonKey_Microphone:
|
|
|
|
ArgonKey Board Microphone
|
|
#########################
|
|
|
|
Overview
|
|
********
|
|
This sample provides an example of how to acquire audio through
|
|
the on-board MP34DT05 microphone. The microphone generates a PDM
|
|
stream which is acquired through I2S. The PDM stream is then
|
|
converted to PCM using the OpenPDMFilter library, which is available
|
|
in source code in this sample.
|
|
|
|
Requirements
|
|
************
|
|
|
|
This sample requires the ArgonKey board plus a USB to TTL 1V8 serial
|
|
cable to get the output audio stream. The board can be powered
|
|
in either one of the following two ways:
|
|
|
|
- mezzanine mode, plugging the ArgonKey to HiKey board through its 96Board
|
|
low-speed connector
|
|
- standalone mode, supplying 5V directly on P1 connector
|
|
|
|
References
|
|
**********
|
|
|
|
- :ref:`96b_argonkey`
|
|
|
|
Building and Running
|
|
********************
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/boards/96b_argonkey/microphone
|
|
:host-os: unix
|
|
:board: 96b_argonkey
|
|
:goals: run
|
|
:compact:
|
|
|
|
Sample Output
|
|
=============
|
|
|
|
The example acquires 5s of audio and prints out the PCM stream on COM port.
|
|
A USB to TTL 1V8 serial cable may be attached to the low speed connector on
|
|
the back of the board on P3.5 (TX) and P3.7 (RX).
|
|
|
|
As soon as the acquisition starts the green LED glows. At the end of the
|
|
acquisition both the green and red LEDs go on and the PCM stream is sent
|
|
on COM port. When the output is completed the green LED goes off and the red
|
|
LED stays on. The process can be reiterated by pressing the RST button.
|
|
|
|
- audio acquisition starts: GRN on - RED off
|
|
- audio acquisition ends: GRN on - RED on
|
|
- audio output ends: GRN off - RED on
|
|
|
|
The characteristics of the PCM audio are hardcoded in the example:
|
|
|
|
- 16KHz sample rate
|
|
- 16 bits per sample
|
|
- 1 channel (mono), as only 1 microphone is available
|
|
|
|
Five seconds of acquisition at a 16KHz sampling rate yields 80,000 16-bit samples.
|
|
The microphone PDM requested clock should lead the MP34DT05 driver to select an
|
|
oversampling/decimation factor equal to 128, resulting in a 2.048MHz bit clock.
|
|
|
|
See pcm and pdm configuration in file :zephyr_file:`samples/boards/96b_argonkey/microphone/src/main.c`.
|
|
|
|
.. note:: It is possible to change the AUDIO_FREQ to 32000 acquiring only 2500 ms. In this
|
|
case the oversampling/decimation factor will be 64.
|
|
|
|
At the end of the acquisition the PCM data will be printed on the terminal
|
|
emulator in either binary or ASCII format. The output is controlled by
|
|
following macro, off by default, in :zephyr_file:`samples/boards/96b_argonkey/microphone/src/main.c`:
|
|
|
|
* :c:macro:`PCM_OUTPUT_IN_ASCII`
|
|
|
|
Binary PCM Output
|
|
-----------------
|
|
|
|
The ttyUSB0 port must be configured in raw mode to avoid having
|
|
characters 'cooked' out.
|
|
|
|
.. code-block:: console
|
|
|
|
stty -F /dev/ttyUSB0 115200 raw
|
|
cat /dev/ttyUSB0 > /tmp/sound.raw
|
|
|
|
.. note:: The "cat /dev/ttyUSB0 > /tmp/sound.raw" command should be launched after the audio
|
|
acquisition starts (after green led glows) to avoid initial boot messages to enter in the file,
|
|
and before audio acquisition ends (before red led glows).
|
|
|
|
.. note:: In case the character 0x0a is interpreted as NL and an 0x0d (CR) is added,
|
|
you may need to remove it::
|
|
|
|
dos2unix -f /tmp/sound.raw
|
|
|
|
ASCII PCM Output
|
|
----------------
|
|
|
|
It is also possible to recompile and to have PCM output in ASCII, which needs
|
|
to be converted to binary later on. The output format is the following:
|
|
|
|
.. code-block:: console
|
|
|
|
ArgonKey test!!
|
|
-- start
|
|
0xfbe0,
|
|
0xfbf0,
|
|
0xfc0c,
|
|
0xfc24,
|
|
0xfc3c,
|
|
0xfc4c,
|
|
0xfc68,
|
|
0xfc48,
|
|
|
|
[...]
|
|
|
|
0xfb98,
|
|
0xfb98,
|
|
0xfbb8,
|
|
0xfbac,
|
|
0xfbc4,
|
|
0xfbe8,
|
|
0xfbf4,
|
|
-- end
|
|
|
|
Play PCM Audio
|
|
--------------
|
|
|
|
Now that we have a binary PCM file (say sound.raw), you can use,
|
|
for example, the audacity open source editor/player to load and play it.
|
|
Use the 'Import->Raw Data' menu to load the sound.raw file as
|
|
signed 16 bit PCM, Little Endian, mono format @16KHz.
|