139 lines
4.1 KiB
Plaintext
139 lines
4.1 KiB
Plaintext
# Kconfig - interrupt controller configuration options
|
|
|
|
#
|
|
# Copyright (c) 2015 Intel Corporation
|
|
#
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
#
|
|
|
|
|
|
menu "Interrupt Controllers"
|
|
|
|
config LOAPIC
|
|
bool "LOAPIC"
|
|
default n
|
|
select IOAPIC
|
|
depends on X86
|
|
help
|
|
This option selects local APIC as the interrupt controller.
|
|
|
|
config LOAPIC_BASE_ADDRESS
|
|
hex "Local APIC Base Address"
|
|
default 0xFEE00000
|
|
depends on LOAPIC
|
|
help
|
|
This option specifies the base address of the Local APIC device.
|
|
|
|
config LOAPIC_SPURIOUS_VECTOR
|
|
bool "Handle LOAPIC spurious interrupts"
|
|
default n
|
|
depends on LOAPIC
|
|
help
|
|
A special situation may occur when a processor raises its task
|
|
priority to be greater than or equal to the level of the
|
|
interrupt for which the processor INTR signal is currently being
|
|
asserted. If at the time the INTA cycle is issued, the
|
|
interrupt that was to be dispensed has become masked (programmed
|
|
by software), the local APIC will deliver a spurious-interrupt
|
|
vector. Dispensing the spurious-interrupt vector does not affect
|
|
the ISR, so the handler for this vector should return without an EOI.
|
|
From x86 manual Volume 3 Section 10.9.
|
|
|
|
config LOAPIC_SPURIOUS_VECTOR_ID
|
|
int "LOAPIC spurious vector ID"
|
|
default -1
|
|
depends on LOAPIC_SPURIOUS_VECTOR
|
|
help
|
|
IDT vector to use for spurious LOAPIC interrupts. Note that some
|
|
arches (P6, Pentium) ignore the low 4 bits and fix them at 0xF.
|
|
If this value is left at -1 the last entry in the IDT will be used.
|
|
|
|
config IOAPIC
|
|
bool "IO-APIC"
|
|
default y
|
|
depends on LOAPIC
|
|
help
|
|
This option signifies that the target has an IO-APIC device. This
|
|
capability allows IO-APIC-dependent code to be included.
|
|
|
|
config IOAPIC_DEBUG
|
|
bool "IO-APIC Debugging"
|
|
default n
|
|
depends on IOAPIC
|
|
help
|
|
Enable debugging for IO-APIC driver.
|
|
|
|
config IOAPIC_BASE_ADDRESS
|
|
hex "IO-APIC Base Address"
|
|
default 0xFEC00000
|
|
depends on IOAPIC
|
|
help
|
|
This option specifies the base address of the IO-APIC device.
|
|
|
|
config IOAPIC_NUM_RTES
|
|
int "Number of Redirection Table Entries available"
|
|
default 24
|
|
depends on IOAPIC
|
|
help
|
|
This option indicates the maximum number of Redirection Table Entries
|
|
(RTEs) (one per IRQ available to the IO-APIC) made available to the
|
|
kernel, regardless of the number provided by the hardware itself. For
|
|
most efficient usage of memory, it should match the number of IRQ lines
|
|
needed by devices connected to the IO-APIC.
|
|
|
|
config IOAPIC_MASK_RTE
|
|
bool "Mask out RTE entries on boot"
|
|
default y
|
|
depends on IOAPIC
|
|
help
|
|
At boot, mask all IOAPIC RTEs if they may be in an undefined state.
|
|
You don't need this if the RTEs are either all guaranteed to be masked
|
|
when the OS starts up, or a previous boot stage has done some IOAPIC
|
|
configuration that needs to be preserved.
|
|
|
|
config MVIC
|
|
bool "Intel Quark D2000 Interrupt Controller (MVIC)"
|
|
default n
|
|
depends on X86
|
|
select X86_FIXED_IRQ_MAPPING
|
|
help
|
|
The MVIC (Intel Quark microcontroller D2000 Interrupt Controller) is
|
|
configured by default to support 32 external interrupt lines. Unlike the
|
|
traditional IA LAPIC/IOAPIC, the interrupt vectors in MVIC are fixed and
|
|
not programmable. In addition, the priorities of these interrupt
|
|
lines are also fixed.
|
|
|
|
config MVIC_TIMER_IRQ
|
|
int "IRQ line to use for timer interrupt"
|
|
range 0 15
|
|
default 10
|
|
depends on MVIC
|
|
help
|
|
Specify the IRQ line to use for the timer interrupt. This should be
|
|
an IRQ line unused by any hardware. If nested interrupts are enabled,
|
|
higher interrupt lines have priority.
|
|
|
|
config ARCV2_INTERRUPT_UNIT
|
|
bool "ARCv2 Interrupt Unit"
|
|
default y
|
|
depends on ARC
|
|
help
|
|
The ARCv2 interrupt unit has 16 allocated exceptions associated with
|
|
vectors 0 to 15 and 240 interrupts associated with vectors 16 to 255.
|
|
The interrupt unit is optional in the ARCv2-based processors. When
|
|
building a processor, you can configure the processor to include an
|
|
interrupt unit. The ARCv2 interrupt unit is highly programmable.
|
|
|
|
config PLIC_FE310
|
|
bool "SiFive Freedom E310 Platform Level Interrupt Controller (PLIC)"
|
|
default y
|
|
depends on SOC_RISCV32_FE310
|
|
select RISCV_HAS_PLIC
|
|
help
|
|
SiFive Freedom E310 Platform Level Interrupt Controller provides support
|
|
for external interrupt lines defined by the FE310 SOC;
|
|
|
|
source "drivers/interrupt_controller/Kconfig.stm32"
|
|
|
|
endmenu
|