268 lines
5.3 KiB
Plaintext
268 lines
5.3 KiB
Plaintext
# Kconfig - Bosch BMI160 inertial measurement configuration options
|
|
|
|
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
#
|
|
|
|
menuconfig BMI160
|
|
bool "Bosch BMI160 inertial measurement unit"
|
|
depends on SPI
|
|
depends on SPI_LEGACY_API
|
|
default n
|
|
help
|
|
Enable Bosch BMI160 inertial measurement unit that provides acceleration
|
|
and angular rate measurements.
|
|
|
|
config BMI160_NAME
|
|
string "Driver's name"
|
|
depends on BMI160
|
|
default "BMI160"
|
|
|
|
config BMI160_SPI_PORT_NAME
|
|
string "SPI master controller port name"
|
|
depends on BMI160
|
|
default ""
|
|
help
|
|
Master SPI port name through which BMI160 chip is accessed.
|
|
|
|
config BMI160_SLAVE
|
|
hex "BMI160 SPI slave select pin"
|
|
depends on BMI160
|
|
default 0
|
|
help
|
|
BMI160 chip select pin.
|
|
|
|
config BMI160_SPI_BUS_FREQ
|
|
int "BMI160 SPI bus speed in Hz"
|
|
default 640000
|
|
depends on BMI160
|
|
help
|
|
This is the maximum supported SPI bus frequency. The chip supports a
|
|
frequency up to 10MHz.
|
|
|
|
choice
|
|
prompt "Trigger mode"
|
|
depends on BMI160
|
|
default BMI160_TRIGGER_GLOBAL_THREAD
|
|
help
|
|
Specify the type of triggering to be used by the driver.
|
|
|
|
config BMI160_TRIGGER_NONE
|
|
bool
|
|
prompt "No trigger"
|
|
|
|
config BMI160_TRIGGER_GLOBAL_THREAD
|
|
bool "Use global thread"
|
|
select BMI160_TRIGGER
|
|
|
|
config BMI160_TRIGGER_OWN_THREAD
|
|
bool "Use own thread"
|
|
select BMI160_TRIGGER
|
|
endchoice
|
|
|
|
config BMI160_TRIGGER
|
|
bool
|
|
depends on BMI160
|
|
|
|
config BMI160_THREAD_PRIORITY
|
|
int "Own thread priority"
|
|
depends on BMI160 && BMI160_TRIGGER_OWN_THREAD
|
|
default 10
|
|
help
|
|
The priority of the thread used for handling interrupts.
|
|
|
|
config BMI160_THREAD_STACK_SIZE
|
|
int "Own thread stack size"
|
|
depends on BMI160 && BMI160_TRIGGER_OWN_THREAD
|
|
default 1024
|
|
help
|
|
The thread stack size.
|
|
|
|
config BMI160_GPIO_DEV_NAME
|
|
string "Gpio device"
|
|
default "GPIO_1"
|
|
depends on BMI160 && BMI160_TRIGGER
|
|
help
|
|
The name of the GPIO device to which the BMI160 interrupt pin is
|
|
connected.
|
|
|
|
config BMI160_GPIO_PIN_NUM
|
|
int "Interrupt GPIO pin number"
|
|
default 4
|
|
depends on BMI160 && BMI160_TRIGGER
|
|
help
|
|
The number of the GPIO pin which is connected to BMI160 interrupt pin.
|
|
|
|
choice
|
|
prompt "Accelerometer power mode"
|
|
depends on BMI160
|
|
default BMI160_ACCEL_PMU_RUNTIME
|
|
|
|
config BMI160_ACCEL_PMU_RUNTIME
|
|
bool "Set at runtime."
|
|
depends on BMI160
|
|
|
|
config BMI160_ACCEL_PMU_SUSPEND
|
|
bool "suspended/not used"
|
|
depends on BMI160
|
|
|
|
config BMI160_ACCEL_PMU_NORMAL
|
|
bool "normal"
|
|
depends on BMI160
|
|
|
|
config BMI160_ACCEL_PMU_LOW_POWER
|
|
bool "low power"
|
|
depends on BMI160
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Accelerometer range setting"
|
|
depends on BMI160 && (BMI160_ACCEL_PMU_RUNTIME || BMI160_ACCEL_PMU_NORMAL || BMI160_ACCEL_PMU_LOW_POWER)
|
|
default BMI160_ACCEL_RANGE_RUNTIME
|
|
|
|
config BMI160_ACCEL_RANGE_RUNTIME
|
|
bool "Set at runtime."
|
|
|
|
config BMI160_ACCEL_RANGE_2G
|
|
bool "2G"
|
|
|
|
config BMI160_ACCEL_RANGE_4G
|
|
bool "4G"
|
|
|
|
config BMI160_ACCEL_RANGE_8G
|
|
bool "8G"
|
|
|
|
config BMI160_ACCEL_RANGE_16G
|
|
bool "16G"
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Accelerometer sampling frequency."
|
|
depends on BMI160 && (BMI160_ACCEL_PMU_RUNTIME || BMI160_ACCEL_PMU_NORMAL || BMI160_ACCEL_PMU_LOW_POWER)
|
|
default BMI160_ACCEL_ODR_RUNTIME
|
|
|
|
config BMI160_ACCEL_ODR_RUNTIME
|
|
bool "Set at runtime."
|
|
|
|
config BMI160_ACCEL_ODR_25_32
|
|
depends on BMI160_ACCEL_PMU_LOW_POWER
|
|
bool "0.78 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_25_16
|
|
depends on BMI160_ACCEL_PMU_LOW_POWER
|
|
bool "1.56 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_25_8
|
|
depends on BMI160_ACCEL_PMU_LOW_POWER
|
|
bool "3.125 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_25_4
|
|
depends on BMI160_ACCEL_PMU_LOW_POWER
|
|
bool "6.25 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_25_2
|
|
bool "12.5 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_25
|
|
bool "25 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_50
|
|
bool "50 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_100
|
|
bool "100 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_200
|
|
bool "200 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_400
|
|
bool "400 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_800
|
|
bool "800 Hz"
|
|
|
|
config BMI160_ACCEL_ODR_1600
|
|
bool "1600 Hz"
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Gyroscope power mode"
|
|
depends on BMI160
|
|
default BMI160_GYRO_PMU_RUNTIME
|
|
|
|
config BMI160_GYRO_PMU_RUNTIME
|
|
bool "Set at runtime."
|
|
depends on BMI160
|
|
|
|
config BMI160_GYRO_PMU_SUSPEND
|
|
bool "suspended/not used"
|
|
depends on BMI160
|
|
|
|
config BMI160_GYRO_PMU_NORMAL
|
|
bool "normal"
|
|
depends on BMI160
|
|
|
|
config BMI160_GYRO_PMU_FAST_STARTUP
|
|
bool "fast start-up"
|
|
depends on BMI160
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Gyroscope range setting."
|
|
depends on BMI160 && (BMI160_GYRO_PMU_RUNTIME || BMI160_GYRO_PMU_NORMAL || BMI160_GYRO_PMU_FAST_STARTUP)
|
|
default BMI160_GYRO_RANGE_RUNTIME
|
|
|
|
config BMI160_GYRO_RANGE_RUNTIME
|
|
bool "Set at runtime."
|
|
|
|
config BMI160_GYRO_RANGE_2000DPS
|
|
bool "2000 DPS"
|
|
|
|
config BMI160_GYRO_RANGE_1000DPS
|
|
bool "1000 DPS"
|
|
|
|
config BMI160_GYRO_RANGE_500DPS
|
|
bool "500 DPS"
|
|
|
|
config BMI160_GYRO_RANGE_250DPS
|
|
bool "250 DPS"
|
|
|
|
config BMI160_GYRO_RANGE_125DPS
|
|
bool "125 DPS"
|
|
endchoice
|
|
|
|
choice
|
|
prompt "Gyroscope sampling frequency."
|
|
depends on BMI160 && (BMI160_GYRO_PMU_RUNTIME || BMI160_GYRO_PMU_NORMAL || BMI160_GYRO_PMU_FAST_STARTUP)
|
|
default BMI160_GYRO_ODR_RUNTIME
|
|
|
|
config BMI160_GYRO_ODR_RUNTIME
|
|
bool "Set at runtime."
|
|
|
|
config BMI160_GYRO_ODR_25
|
|
bool "25 Hz"
|
|
|
|
config BMI160_GYRO_ODR_50
|
|
bool "50 Hz"
|
|
|
|
config BMI160_GYRO_ODR_100
|
|
bool "100 Hz"
|
|
|
|
config BMI160_GYRO_ODR_200
|
|
bool "200 Hz"
|
|
|
|
config BMI160_GYRO_ODR_400
|
|
bool "400 Hz"
|
|
|
|
config BMI160_GYRO_ODR_800
|
|
bool "800 Hz"
|
|
|
|
config BMI160_GYRO_ODR_1600
|
|
bool "1600 Hz"
|
|
|
|
config BMI160_GYRO_ODR_3200
|
|
bool "3200 Hz"
|
|
endchoice
|