179 lines
5.5 KiB
ReStructuredText
179 lines
5.5 KiB
ReStructuredText
.. _nucleo_l053r8_board:
|
|
|
|
ST Nucleo L053R8
|
|
################
|
|
|
|
Overview
|
|
********
|
|
The STM32 Nucleo-64 development board with STM32L053R8 MCU, supports Arduino and ST morpho connectivity.
|
|
|
|
The STM32 Nucleo board provides an affordable, and flexible way for users to try out new concepts,
|
|
and build prototypes with the STM32 microcontroller, choosing from the various
|
|
combinations of performance, power consumption, and features.
|
|
|
|
The Arduino* Uno V3 connectivity support and the ST morpho headers allow easy functionality
|
|
expansion of the STM32 Nucleo open development platform with a wide choice of
|
|
specialized shields.
|
|
|
|
The STM32 Nucleo board integrates the ST-LINK/V2-1 debugger and programmer.
|
|
|
|
The STM32 Nucleo board comes with the STM32 comprehensive software HAL library together
|
|
with various packaged software examples.
|
|
|
|
.. image:: img/nucleo_l053r8.jpg
|
|
:width: 500px
|
|
:height: 367px
|
|
:align: center
|
|
:alt: Nucleo L053R8
|
|
|
|
More information about the board can be found at the `Nucleo L053R8 website`_.
|
|
|
|
Hardware
|
|
********
|
|
Nucleo L053R8 provides the following hardware components:
|
|
|
|
- STM32 microcontroller in QFP64 package
|
|
- Two types of extension resources:
|
|
|
|
- Arduino* Uno V3 connectivity
|
|
- ST morpho extension pin headers for full access to all STM32 I/Os
|
|
|
|
- ARM* mbed*
|
|
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector:
|
|
|
|
- Selection-mode switch to use the kit as a standalone ST-LINK/V2-1
|
|
|
|
- Flexible board power supply:
|
|
|
|
- USB VBUS or external source (3.3V, 5V, 7 - 12V)
|
|
- Power management access point
|
|
|
|
- Three LEDs:
|
|
|
|
- USB communication (LD1), user LED (LD2), power LED (LD3)
|
|
|
|
- Two push-buttons: USER and RESET
|
|
- USB re-enumeration capability. Three different interfaces supported on USB:
|
|
|
|
- Virtual COM port
|
|
- Mass storage
|
|
- Debug port
|
|
|
|
- Support of wide choice of Integrated Development Environments (IDEs) including:
|
|
|
|
- IAR
|
|
- ARM Keil
|
|
- GCC-based IDEs
|
|
|
|
More information about STM32L053R8 can be found in the
|
|
`STM32L0x3 reference manual`_
|
|
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The Zephyr nucleo_l053r8 board configuration supports the following hardware features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| CLOCK | on-chip | reset and clock control |
|
|
+-----------+------------+-------------------------------------+
|
|
| I2C | on-chip | i2c controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| SPI | on-chip | spi controller |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
Other hardware features are not yet supported in this Zephyr port.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
``boards/arm/nucleo_l053r8/nucleo_l053r8_defconfig``
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as
|
|
input (with or without pull-up or pull-down), or as peripheral alternate function. Most of the
|
|
GPIO pins are shared with digital or analog alternate functions. All GPIOs are high current
|
|
capable except for analog inputs.
|
|
|
|
Board connectors:
|
|
-----------------
|
|
.. image:: img/nucleo_l053r8_connectors.png
|
|
:width: 800px
|
|
:align: center
|
|
:height: 619px
|
|
:alt: Nucleo L053R8 connectors
|
|
|
|
Default Zephyr Peripheral Mapping:
|
|
----------------------------------
|
|
|
|
- UART_1 TX/RX : PB6/PB7
|
|
- UART_2 TX/RX : PA2/PA3 (ST-Link Virtual Port Com)
|
|
- I2C1 SCL/SDA : PB8/PB9 (Arduino I2C)
|
|
- SPI1 SCK/MISO/MOSI : PA5/PA6/PA7 (Arduino SPI)
|
|
- USER_PB : PC13
|
|
- LD2 : PA5
|
|
|
|
For mode details please refer to `STM32 Nucleo-64 board User Manual`_.
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Applications for the ``nucleo_l053r8`` board configuration can be built and
|
|
flashed in the usual way (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Flashing
|
|
========
|
|
|
|
Nucleo L053R8 board includes an ST-LINK/V2-1 embedded debug tool interface.
|
|
This interface is supported by the openocd version included in the Zephyr SDK.
|
|
|
|
Flashing an application to Nucleo L053R8
|
|
----------------------------------------
|
|
|
|
Here is an example for the :ref:`blinky-sample` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/basic/blinky
|
|
:board: nucleo_l053r8
|
|
:goals: build flash
|
|
|
|
You will see the LED blinking every second.
|
|
|
|
Debugging
|
|
=========
|
|
|
|
You can debug an application in the usual way. Here is an example for the
|
|
:ref:`hello_world` application.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: nucleo_l053r8
|
|
:maybe-skip-config:
|
|
:goals: debug
|
|
|
|
References
|
|
**********
|
|
|
|
.. target-notes::
|
|
|
|
.. _Nucleo L053R8 website:
|
|
http://www.st.com/en/evaluation-tools/nucleo-l053r8.html
|
|
|
|
.. _STM32L0x3 reference manual:
|
|
http://www.st.com/resource/en/reference_manual/dm00095744.pdf
|
|
|
|
.. _STM32 Nucleo-64 board User Manual:
|
|
http://www.st.com/resource/en/user_manual/dm00105823.pdf
|