146 lines
3.4 KiB
Plaintext
146 lines
3.4 KiB
Plaintext
# Thingy53 NRF5340 board configuration
|
|
|
|
# Copyright (c) 2021 Nordic Semiconductor ASA
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
if BOARD_THINGY53_NRF5340_CPUAPP || BOARD_THINGY53_NRF5340_CPUAPP_NS
|
|
|
|
# Code Partition:
|
|
#
|
|
# For the secure version of the board the firmware is linked at the beginning
|
|
# of the flash, or into the code-partition defined in DT if it is intended to
|
|
# be loaded by MCUboot. If the secure firmware is to be combined with a non-
|
|
# secure image (TRUSTED_EXECUTION_SECURE=y), the secure FW image shall always
|
|
# be restricted to the size of its code partition.
|
|
#
|
|
# For the non-secure version of the board, the firmware
|
|
# must be linked into the code-partition (non-secure) defined in DT, regardless.
|
|
# Apply this configuration below by setting the Kconfig symbols used by
|
|
# the linker according to the information extracted from DT partitions.
|
|
|
|
# SRAM Partition:
|
|
#
|
|
# If the secure firmware is to be combined with a non-secure image
|
|
# (TRUSTED_EXECUTION_SECURE=y), the secure FW image SRAM shall always
|
|
# be restricted to the secure image SRAM partition (sram-secure-partition).
|
|
# Otherwise (if TRUSTED_EXECUTION_SECURE is not set) the whole zephyr,sram
|
|
# may be used by the image.
|
|
#
|
|
# For the non-secure version of the board, the firmware image SRAM is
|
|
# always restricted to the allocated non-secure SRAM partition.
|
|
#
|
|
# Workaround for not being able to have commas in macro arguments
|
|
DT_CHOSEN_Z_CODE_PARTITION := zephyr,code-partition
|
|
DT_CHOSEN_Z_SRAM_PARTITION := zephyr,sram-secure-partition
|
|
|
|
if BOARD_THINGY53_NRF5340_CPUAPP && TRUSTED_EXECUTION_SECURE
|
|
|
|
config FLASH_LOAD_SIZE
|
|
default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
config SRAM_SIZE
|
|
default $(dt_chosen_reg_size_int,$(DT_CHOSEN_Z_SRAM_PARTITION),0,K)
|
|
|
|
endif # BOARD_THINGY53_NRF5340_CPUAPP && TRUSTED_EXECUTION_SECURE
|
|
|
|
if BOARD_THINGY53_NRF5340_CPUAPP_NS
|
|
|
|
config FLASH_LOAD_OFFSET
|
|
default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
config FLASH_LOAD_SIZE
|
|
default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
endif # BOARD_THINGY53_NRF5340_CPUAPP_NS
|
|
|
|
if !TRUSTED_EXECUTION_SECURE
|
|
|
|
config BT_HCI_IPC
|
|
default y if BT
|
|
|
|
config HEAP_MEM_POOL_ADD_SIZE_BOARD
|
|
int
|
|
default 4096 if BT_HCI_IPC
|
|
|
|
config BT_HAS_HCI_VS
|
|
default BT
|
|
|
|
config USB_NRFX_ATTACHED_EVENT_DELAY
|
|
default 700 if USB_DEVICE_DRIVER
|
|
|
|
config I2C
|
|
default y
|
|
|
|
config SPI
|
|
default y
|
|
|
|
config REGULATOR
|
|
default y
|
|
|
|
endif # !TRUSTED_EXECUTION_SECURE
|
|
|
|
if BOARD_SERIAL_BACKEND_CDC_ACM
|
|
|
|
config USB_DEVICE_PRODUCT
|
|
default "Thingy:53 Application"
|
|
|
|
config USB_DEVICE_VID
|
|
default 0x1915
|
|
|
|
config USB_DEVICE_PID
|
|
default 0x530C
|
|
|
|
config USB_DEVICE_STACK
|
|
default y
|
|
|
|
config USB_CDC_ACM
|
|
default y
|
|
|
|
config UART_CONSOLE
|
|
default CONSOLE
|
|
|
|
config USB_DEVICE_INITIALIZE_AT_BOOT
|
|
default y if !MCUBOOT
|
|
|
|
config SHELL_BACKEND_SERIAL_CHECK_DTR
|
|
default SHELL
|
|
depends on UART_LINE_CTRL
|
|
|
|
config UART_LINE_CTRL
|
|
default SHELL
|
|
|
|
config USB_DEVICE_REMOTE_WAKEUP
|
|
default n
|
|
|
|
if LOG
|
|
|
|
# Logger cannot use itself to log
|
|
choice USB_CDC_ACM_LOG_LEVEL_CHOICE
|
|
default USB_CDC_ACM_LOG_LEVEL_OFF
|
|
endchoice
|
|
|
|
# Set USB log level to error only
|
|
choice USB_DEVICE_LOG_LEVEL_CHOICE
|
|
default USB_DEVICE_LOG_LEVEL_ERR
|
|
endchoice
|
|
|
|
# Wait 4000ms at startup for logging
|
|
config LOG_PROCESS_THREAD_STARTUP_DELAY_MS
|
|
default 4000
|
|
|
|
endif # LOG
|
|
|
|
endif # BOARD_SERIAL_BACKEND_CDC_ACM
|
|
|
|
endif # BOARD_THINGY53_NRF5340_CPUAPP || BOARD_THINGY53_NRF5340_CPUAPP_NS
|
|
|
|
if BOARD_THINGY53_NRF5340_CPUNET
|
|
|
|
config BT_CTLR
|
|
default BT
|
|
|
|
config BT_ECC
|
|
default BT
|
|
|
|
endif # BOARD_THINGY53_NRF5340_CPUNET
|