178 lines
4.4 KiB
Plaintext
178 lines
4.4 KiB
Plaintext
# Kconfig - console driver configuration options
|
|
|
|
#
|
|
# Copyright (c) 2014-2015 Wind River Systems, Inc.
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
menuconfig CONSOLE
|
|
bool
|
|
prompt "Console drivers"
|
|
|
|
if CONSOLE
|
|
|
|
config CONSOLE_HAS_DRIVER
|
|
bool
|
|
default n
|
|
help
|
|
This is an option to be enabled by console drivers to signal
|
|
that some kind of console exists.
|
|
|
|
config CONSOLE_HANDLER
|
|
bool
|
|
prompt "Enable console input handler"
|
|
depends on UART_CONSOLE
|
|
select UART_INTERRUPT_DRIVEN
|
|
default n
|
|
help
|
|
This option enables console input handler allowing to write simple
|
|
interaction between serial console and the OS.
|
|
|
|
config CONSOLE_HANDLER_SHELL
|
|
bool
|
|
prompt "Enable console input handler [ Experimental ]"
|
|
default n
|
|
depends on CONSOLE_HANDLER
|
|
help
|
|
Shell implementation based on CONSOLE_HANDLER.
|
|
|
|
config CONSOLE_HANDLER_SHELL_STACKSIZE
|
|
int
|
|
prompt "Console handler shell stack size"
|
|
default 2000
|
|
depends on CONSOLE_HANDLER_SHELL
|
|
help
|
|
Stack size for the console handler shell.
|
|
|
|
config UART_CONSOLE
|
|
bool
|
|
prompt "Use UART for console"
|
|
default n
|
|
depends on SERIAL && SERIAL_HAS_DRIVER
|
|
select CONSOLE_HAS_DRIVER
|
|
help
|
|
Enable this option to use one UART for console. Make sure
|
|
CONFIG_UART_CONSOLE_ON_DEV_NAME is also set correctly.
|
|
|
|
config UART_CONSOLE_ON_DEV_NAME
|
|
string "Device Name of UART Device for UART Console"
|
|
default "UART_0"
|
|
depends on UART_CONSOLE
|
|
help
|
|
This option specifies the name of UART device to be used for
|
|
UART console.
|
|
|
|
config UART_CONSOLE_IRQ
|
|
int "IRQ of UART Device for UART Console"
|
|
depends on UART_CONSOLE
|
|
help
|
|
This option specifies the IRQ of UART device to be used for
|
|
UART console.
|
|
|
|
config UART_CONSOLE_IRQ_PRI
|
|
int "IRQ of UART Device for UART Console"
|
|
depends on UART_CONSOLE
|
|
help
|
|
This option specifies the IRQ priorityof UART device to be
|
|
used for UART console.
|
|
|
|
config UART_CONSOLE_PRIORITY
|
|
int
|
|
prompt "Init priority"
|
|
default 60
|
|
depends on UART_CONSOLE
|
|
help
|
|
Device driver initialization priority.
|
|
Console has to be initialized after the UART driver
|
|
it uses.
|
|
|
|
config RAM_CONSOLE
|
|
bool
|
|
prompt "Use RAM console"
|
|
select CONSOLE_HAS_DRIVER
|
|
default n
|
|
help
|
|
Emit console messages to a RAM buffer "ram_console" which can
|
|
be examined at runtime with a debugger. Useful in board bring-up
|
|
if there aren't any working serial drivers.
|
|
|
|
config RAM_CONSOLE_BUFFER_SIZE
|
|
int "Ram Console buffer size"
|
|
default 1024
|
|
depends on RAM_CONSOLE
|
|
help
|
|
Size of the RAM console buffer. Messages will wrap around if the
|
|
length is exceeded.
|
|
|
|
config IPM_CONSOLE_SENDER
|
|
bool
|
|
prompt "Inter-processor Mailbox console sender"
|
|
select CONSOLE_HAS_DRIVER
|
|
default n
|
|
help
|
|
Enable the sending side of IPM console
|
|
|
|
config IPM_CONSOLE_RECEIVER
|
|
bool
|
|
prompt "Inter-processor Mailbox console receiver"
|
|
select RING_BUFFER
|
|
default n
|
|
help
|
|
Enable the receiving side of IPM console
|
|
|
|
config IPM_CONSOLE_PRIORITY
|
|
int
|
|
prompt "IPM console init priority"
|
|
default 60
|
|
depends on IPM_CONSOLE_SENDER || IPM_CONSOLE_RECEIVER
|
|
help
|
|
Device driver initialization priority.
|
|
Console has to be initialized after the IPM subsystem
|
|
it uses.
|
|
|
|
config UART_PIPE
|
|
bool
|
|
prompt "Enable pipe UART driver"
|
|
select UART_INTERRUPT_DRIVEN
|
|
default n
|
|
help
|
|
Enable pipe UART driver. This driver allows application to communicate
|
|
over UART with custom defined protocol. Driver doesn't inspect received
|
|
data (as contrary to console UART driver) and all aspects of received
|
|
protocol data are handled by application provided callback.
|
|
|
|
config UART_PIPE_ON_DEV_NAME
|
|
string "Device Name of UART Device for pipe UART"
|
|
default "UART_0"
|
|
depends on UART_PIPE
|
|
help
|
|
This option specifies the name of UART device to be used
|
|
for pipe UART.
|
|
|
|
config UART_PIPE_IRQ
|
|
int "IRQ for pipe UART"
|
|
depends on UART_PIPE
|
|
help
|
|
This option specifies the IRQ of UART device to be used
|
|
for pipe UART.
|
|
|
|
config UART_PIPE_IRQ_PRI
|
|
int "IRQ Priority for pipe UART"
|
|
depends on UART_PIPE
|
|
help
|
|
This option specifies the IRQ priority of UART device
|
|
to be used for pipe UART.
|
|
|
|
endif
|