133 lines
2.4 KiB
Plaintext
133 lines
2.4 KiB
Plaintext
/*
|
|
* Copyright (c) 2017 Florian Vaussard, HEIG-VD
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/f4/stm32f413Xh.dtsi>
|
|
#include <st/f4/stm32f413z(g-h)tx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
#include <zephyr/dt-bindings/input/input-event-codes.h>
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32F413ZH-NUCLEO board";
|
|
compatible = "st,stm32f413zh-nucleo";
|
|
|
|
chosen {
|
|
zephyr,console = &usart3;
|
|
zephyr,shell-uart = &usart3;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
green_led_1: led_1 {
|
|
gpios = <&gpiob 0 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD1";
|
|
};
|
|
blue_led_1: led_2 {
|
|
gpios = <&gpiob 7 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
red_led_1: led_3 {
|
|
gpios = <&gpiob 14 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD3";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_ACTIVE_HIGH>;
|
|
zephyr,code = <INPUT_KEY_0>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led_1;
|
|
led1 = &blue_led_1;
|
|
led2 = &red_led_1;
|
|
sw0 = &user_button;
|
|
};
|
|
};
|
|
|
|
&clk_lsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&clk_hse {
|
|
hse-bypass;
|
|
clock-frequency = <DT_FREQ_M(8)>; /* STLink 8MHz clock */
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
div-m = <8>;
|
|
mul-n = <384>;
|
|
div-p = <4>;
|
|
div-q = <8>;
|
|
clocks = <&clk_hse>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rcc {
|
|
clocks = <&pll>;
|
|
clock-frequency = <DT_FREQ_M(96)>;
|
|
ahb-prescaler = <1>;
|
|
apb1-prescaler = <2>;
|
|
apb2-prescaler = <1>;
|
|
};
|
|
|
|
&usart3 {
|
|
pinctrl-0 = <&usart3_tx_pd8 &usart3_rx_pd9>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart6 {
|
|
pinctrl-0 = <&usart6_tx_pg14 &usart6_rx_pg9>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&spi1 {
|
|
pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>;
|
|
pinctrl-names = "default";
|
|
cs-gpios = <&gpiod 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
|
|
status = "okay";
|
|
};
|
|
|
|
zephyr_udc0: &usbotg_fs {
|
|
pinctrl-0 = <&usb_otg_fs_dm_pa11 &usb_otg_fs_dp_pa12>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&timers2 {
|
|
status = "okay";
|
|
|
|
pwm2: pwm {
|
|
status = "okay";
|
|
pinctrl-0 = <&tim2_ch1_pa0>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&rtc {
|
|
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
|
|
<&rcc STM32_SRC_LSI RTC_SEL(2)>;
|
|
status = "okay";
|
|
};
|