137 lines
2.5 KiB
Plaintext
137 lines
2.5 KiB
Plaintext
/*
|
|
* Copyright (c) 2017 RnDity Sp. z o.o.
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/f0/stm32f030X8.dtsi>
|
|
#include <st/f0/stm32f030r8tx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
#include "st_morpho_connector.dtsi"
|
|
#include <zephyr/dt-bindings/input/input-event-codes.h>
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32F030R8-NUCLEO board";
|
|
compatible = "st,stm32f030r8-nucleo";
|
|
|
|
chosen {
|
|
zephyr,console = &usart2;
|
|
zephyr,shell-uart = &usart2;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
green_led_2: led_2 {
|
|
gpios = <&gpioa 5 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
|
|
zephyr,code = <INPUT_KEY_0>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led_2;
|
|
sw0 = &user_button;
|
|
watchdog0 = &iwdg;
|
|
die-temp0 = &die_temp;
|
|
volt-sensor0 = &vref;
|
|
};
|
|
};
|
|
|
|
&clk_hse {
|
|
hse-bypass;
|
|
clock-frequency = <DT_FREQ_M(8)>; /* STLink 8MHz clock */
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
prediv = <1>;
|
|
mul = <6>;
|
|
clocks = <&clk_hse>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rcc {
|
|
clocks = <&pll>;
|
|
clock-frequency = <DT_FREQ_M(48)>;
|
|
ahb-prescaler = <1>;
|
|
apb1-prescaler = <1>;
|
|
};
|
|
|
|
/* Due to limited available memory, don't enable gpiod and gpiof */
|
|
/* (Test cases fail due to 'SRAM' region overflow) */
|
|
&gpiod {status = "disabled";};
|
|
&gpiof {status = "disabled";};
|
|
|
|
&usart1 {
|
|
pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart2 {
|
|
pinctrl-0 = <&usart2_tx_pa2 &usart2_rx_pa3>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&i2c2 {
|
|
pinctrl-0 = <&i2c2_scl_pb10 &i2c2_sda_pb11>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&spi1 {
|
|
pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>;
|
|
pinctrl-names = "default";
|
|
cs-gpios = <&gpiob 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&spi2 {
|
|
pinctrl-0 = <&spi2_nss_pb12 &spi2_sck_pb13
|
|
&spi2_miso_pb14 &spi2_mosi_pb15>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&adc1 {
|
|
pinctrl-0 = <&adc_in0_pa0>;
|
|
pinctrl-names = "default";
|
|
st,adc-clock-source = <SYNC>;
|
|
st,adc-prescaler = <4>;
|
|
status = "okay";
|
|
};
|
|
|
|
&iwdg {
|
|
status = "okay";
|
|
};
|
|
|
|
&die_temp {
|
|
status = "okay";
|
|
};
|
|
|
|
&vref {
|
|
status = "okay";
|
|
};
|