361 lines
7.6 KiB
C
361 lines
7.6 KiB
C
/*
|
|
* Copyright (c) 2015 Intel Corporation.
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the "License");
|
|
* you may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*/
|
|
|
|
/**
|
|
* @file Driver for the MMIO-based GPIO driver.
|
|
*/
|
|
|
|
#include <errno.h>
|
|
|
|
#include <nanokernel.h>
|
|
|
|
#include <gpio.h>
|
|
|
|
#include "gpio_mmio.h"
|
|
|
|
#if defined(CONFIG_GPIO_MMIO_0_ACCESS_MM) \
|
|
|| defined(CONFIG_GPIO_MMIO_1_ACCESS_MM)
|
|
|
|
static uint32_t _mm_set_bit(uint32_t addr, uint32_t bit, uint32_t value)
|
|
{
|
|
if (!value) {
|
|
sys_clear_bit(addr, bit);
|
|
} else {
|
|
sys_set_bit(addr, bit);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static uint32_t _mm_read(uint32_t addr, uint32_t bit, uint32_t value)
|
|
{
|
|
ARG_UNUSED(bit);
|
|
ARG_UNUSED(value);
|
|
|
|
return sys_read32(addr);
|
|
}
|
|
|
|
static uint32_t _mm_write(uint32_t addr, uint32_t bit, uint32_t value)
|
|
{
|
|
ARG_UNUSED(bit);
|
|
|
|
sys_write32(value, addr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#endif /* if direct memory access is needed */
|
|
|
|
#if defined(CONFIG_GPIO_MMIO_0_ACCESS_IO) \
|
|
|| defined(CONFIG_GPIO_MMIO_1_ACCESS_IO)
|
|
|
|
static uint32_t _io_set_bit(uint32_t addr, uint32_t bit, uint32_t value)
|
|
{
|
|
if (!value) {
|
|
sys_io_clear_bit(addr, bit);
|
|
} else {
|
|
sys_io_set_bit(addr, bit);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static uint32_t _io_read(uint32_t addr, uint32_t bit, uint32_t value)
|
|
{
|
|
ARG_UNUSED(bit);
|
|
ARG_UNUSED(value);
|
|
|
|
return sys_in32(addr);
|
|
}
|
|
|
|
static uint32_t _io_write(uint32_t addr, uint32_t bit, uint32_t value)
|
|
{
|
|
ARG_UNUSED(bit);
|
|
|
|
sys_out32(value, addr);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#endif /* if io port access is needed */
|
|
|
|
/**
|
|
* @brief Configurate pin or port
|
|
*
|
|
* @param dev Device struct
|
|
* @param access_op Access operation (pin or port)
|
|
* @param pin The pin number
|
|
* @param flags Flags of pin or port
|
|
*
|
|
* @return 0 if successful, failed otherwise
|
|
*/
|
|
static int gpio_mmio_config(struct device *dev,
|
|
int access_op, uint32_t pin, int flags)
|
|
{
|
|
const struct gpio_mmio_config * const cfg =
|
|
dev->config->config_info;
|
|
uint32_t value = 0;
|
|
|
|
/* Setup direction register */
|
|
|
|
if (!cfg->reg.dir) {
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (cfg->cfg_flags & GPIO_MMIO_CFG_DIR_MASK) {
|
|
/* Direction register is inverse
|
|
* INV: 0 - pin is input, 1 - pin is output
|
|
*/
|
|
if ((flags & GPIO_DIR_MASK) == GPIO_DIR_IN) {
|
|
value = 0x0;
|
|
} else {
|
|
value = 0xFFFFFFFF;
|
|
}
|
|
} else {
|
|
/* Direction register is normal.
|
|
* NORMAL: 0 - pin is output, 1 - pin is input
|
|
*/
|
|
if ((flags & GPIO_DIR_MASK) == GPIO_DIR_IN) {
|
|
value = 0xFFFFFFFF;
|
|
} else {
|
|
value = 0x0;
|
|
}
|
|
}
|
|
|
|
switch (access_op) {
|
|
case GPIO_ACCESS_BY_PIN:
|
|
cfg->access.set_bit(cfg->reg.dir, pin, value);
|
|
break;
|
|
case GPIO_ACCESS_BY_PORT:
|
|
cfg->access.write(cfg->reg.dir, 0, value);
|
|
break;
|
|
default:
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
/*
|
|
* Enable the GPIO pin(s), since the direction is
|
|
* also being setup. This indicates pin(s) is being used.
|
|
*
|
|
* This is not really necessary, so don't fail if
|
|
* register is not defined.
|
|
*/
|
|
|
|
if (!cfg->reg.en) {
|
|
return 0;
|
|
}
|
|
|
|
if (cfg->cfg_flags & GPIO_MMIO_CFG_EN_MASK) {
|
|
/* INV: 0 - enable, 1 - disable */
|
|
value = 0x0;
|
|
} else {
|
|
/* NORMAL: 0 - disable, 1 - enable */
|
|
value = 0xFFFFFFFF;
|
|
}
|
|
|
|
switch (access_op) {
|
|
case GPIO_ACCESS_BY_PIN:
|
|
cfg->access.set_bit(cfg->reg.en, pin, value);
|
|
break;
|
|
case GPIO_ACCESS_BY_PORT:
|
|
cfg->access.write(cfg->reg.en, 0, value);
|
|
break;
|
|
default:
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* @brief Set the pin or port output
|
|
*
|
|
* @param dev Device struct
|
|
* @param access_op Access operation (pin or port)
|
|
* @param pin The pin number
|
|
* @param value Value to set (0 or 1)
|
|
*
|
|
* @return 0 if successful, failed otherwise
|
|
*/
|
|
static int gpio_mmio_write(struct device *dev, int access_op,
|
|
uint32_t pin, uint32_t value)
|
|
{
|
|
const struct gpio_mmio_config * const cfg =
|
|
dev->config->config_info;
|
|
|
|
if (!cfg->reg.output) {
|
|
return -EINVAL;
|
|
}
|
|
|
|
switch (access_op) {
|
|
case GPIO_ACCESS_BY_PIN:
|
|
cfg->access.set_bit(cfg->reg.output, pin, value);
|
|
break;
|
|
case GPIO_ACCESS_BY_PORT:
|
|
cfg->access.write(cfg->reg.output, 0, value);
|
|
break;
|
|
default:
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* @brief Read the pin or port status
|
|
*
|
|
* @param dev Device struct
|
|
* @param access_op Access operation (pin or port)
|
|
* @param pin The pin number
|
|
* @param value Value of input pin(s)
|
|
*
|
|
* @return 0 if successful, failed otherwise
|
|
*/
|
|
static int gpio_mmio_read(struct device *dev,
|
|
int access_op, uint32_t pin, uint32_t *value)
|
|
{
|
|
const struct gpio_mmio_config * const cfg =
|
|
dev->config->config_info;
|
|
|
|
if (!cfg->reg.input) {
|
|
return -EINVAL;
|
|
}
|
|
|
|
switch (access_op) {
|
|
case GPIO_ACCESS_BY_PIN:
|
|
*value = cfg->access.read(cfg->reg.input, 0, 0);
|
|
*value &= BIT(pin) >> pin;
|
|
break;
|
|
case GPIO_ACCESS_BY_PORT:
|
|
*value = cfg->access.read(cfg->reg.input, 0, 0);
|
|
break;
|
|
default:
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int gpio_mmio_set_callback(struct device *dev, gpio_callback_t callback)
|
|
{
|
|
ARG_UNUSED(dev);
|
|
ARG_UNUSED(callback);
|
|
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
static int gpio_mmio_enable_callback(struct device *dev,
|
|
int access_op, uint32_t pin)
|
|
{
|
|
ARG_UNUSED(dev);
|
|
ARG_UNUSED(access_op);
|
|
ARG_UNUSED(pin);
|
|
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
static int gpio_mmio_disable_callback(struct device *dev,
|
|
int access_op, uint32_t pin)
|
|
{
|
|
ARG_UNUSED(dev);
|
|
ARG_UNUSED(access_op);
|
|
ARG_UNUSED(pin);
|
|
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
static struct gpio_driver_api gpio_mmio_drv_api_funcs = {
|
|
.config = gpio_mmio_config,
|
|
.write = gpio_mmio_write,
|
|
.read = gpio_mmio_read,
|
|
.set_callback = gpio_mmio_set_callback,
|
|
.enable_callback = gpio_mmio_enable_callback,
|
|
.disable_callback = gpio_mmio_disable_callback,
|
|
};
|
|
|
|
/**
|
|
* @brief Initialization function of MMIO
|
|
*
|
|
* @param dev Device struct
|
|
* @return 0 if successful, failed otherwise.
|
|
*/
|
|
int gpio_mmio_init(struct device *dev)
|
|
{
|
|
dev->driver_api = &gpio_mmio_drv_api_funcs;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/* Initialization for MMIO_0 */
|
|
#ifdef CONFIG_GPIO_MMIO_0
|
|
#include <device.h>
|
|
#include <init.h>
|
|
|
|
static struct gpio_mmio_config gpio_mmio_0_cfg = {
|
|
.cfg_flags = CONFIG_GPIO_MMIO_0_CFG,
|
|
|
|
.reg.en = CONFIG_GPIO_MMIO_0_EN,
|
|
.reg.dir = CONFIG_GPIO_MMIO_0_DIR,
|
|
.reg.input = CONFIG_GPIO_MMIO_0_INPUT,
|
|
.reg.output = CONFIG_GPIO_MMIO_0_OUTPUT,
|
|
|
|
#ifdef CONFIG_GPIO_MMIO_0_ACCESS_IO
|
|
.access.set_bit = _io_set_bit,
|
|
.access.read = _io_read,
|
|
.access.write = _io_write,
|
|
#else /* below is for CONFIG_GPIO_MMIO_0_ACCESS_MM=y or else */
|
|
.access.set_bit = _mm_set_bit,
|
|
.access.read = _mm_read,
|
|
.access.write = _mm_write,
|
|
#endif
|
|
};
|
|
|
|
DEVICE_INIT(gpio_mmio_0, CONFIG_GPIO_MMIO_0_DEV_NAME, gpio_mmio_init,
|
|
NULL, &gpio_mmio_0_cfg,
|
|
SECONDARY, CONFIG_GPIO_MMIO_INIT_PRIORITY);
|
|
|
|
#endif /* CONFIG_GPIO_MMIO_0 */
|
|
|
|
/* Initialization for MMIO_1 */
|
|
#ifdef CONFIG_GPIO_MMIO_1
|
|
#include <device.h>
|
|
#include <init.h>
|
|
|
|
static struct gpio_mmio_config gpio_mmio_1_cfg = {
|
|
.cfg_flags = CONFIG_GPIO_MMIO_0_CFG,
|
|
|
|
.reg.en = CONFIG_GPIO_MMIO_1_EN,
|
|
.reg.dir = CONFIG_GPIO_MMIO_1_DIR,
|
|
.reg.input = CONFIG_GPIO_MMIO_1_INPUT,
|
|
.reg.output = CONFIG_GPIO_MMIO_1_OUTPUT,
|
|
|
|
#ifdef CONFIG_GPIO_MMIO_1_ACCESS_IO
|
|
.access.set_bit = _io_set_bit,
|
|
.access.read = _io_read,
|
|
.access.write = _io_write,
|
|
#else /* below is for CONFIG_GPIO_MMIO_1_ACCESS_MM=y or else */
|
|
.access.set_bit = _mm_set_bit,
|
|
.access.read = _mm_read,
|
|
.access.write = _mm_write,
|
|
#endif
|
|
};
|
|
|
|
DEVICE_INIT(gpio_mmio_1, CONFIG_GPIO_MMIO_1_DEV_NAME, gpio_mmio_init,
|
|
NULL, &gpio_mmio_1_cfg,
|
|
SECONDARY, CONFIG_GPIO_MMIO_INIT_PRIORITY);
|
|
|
|
#endif /* CONFIG_GPIO_MMIO_1 */
|