OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/drivers/regulator/regulator_pca9420.c

559 lines
19 KiB
C
Raw Blame History

/*
* Copyright (c) 2021 NXP
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT nxp_pca9420
#include <errno.h>
#include <zephyr/kernel.h>
#include <zephyr/drivers/i2c.h>
#include <zephyr/drivers/regulator.h>
#include <zephyr/drivers/regulator/pca9420.h>
#include <zephyr/sys/linear_range.h>
#include <zephyr/sys/util.h>
/** Register memory map. See datasheet for more details. */
/** General purpose registers */
/** @brief Top level system ctrl 0 */
#define PCA9420_TOP_CNTL0 0x09U
/** @brief Top level system ctrl 2 */
#define PCA9420_TOP_CNTL2 0x0BU
/** @brief Top level system ctrl 3 */
#define PCA9420_TOP_CNTL3 0x0CU
/** Regulator status indication registers */
/** @brief Active Discharge configuration for mode 0_0 */
#define PCA9420_ACT_DISCHARGE_CNTL 0x21U
/** @brief Mode configuration for mode 0_0 */
#define PCA9420_MODECFG_0_0 0x22U
/** @brief Mode configuration for mode 0_1 */
#define PCA9420_MODECFG_0_1 0x23U
/** @brief Mode configuration for mode 0_2 */
#define PCA9420_MODECFG_0_2 0x24U
/** @brief Mode configuration for mode 0_3 */
#define PCA9420_MODECFG_0_3 0x25U
/** @brief VIN input current limit selection */
#define PCA9420_TOP_CNTL0_VIN_ILIM_SEL_POS 5U
#define PCA9420_TOP_CNTL0_VIN_ILIM_SEL_MASK 0xE0U
#define PCA9420_TOP_CNTL0_VIN_ILIM_SEL_DISABLED 0x7U
/** @brief ASYS UVLO threshold selection */
#define PCA9420_TOP_CNTL2_ASYS_UVLO_SEL_POS 6U
#define PCA9420_TOP_CNTL2_ASYS_UVLO_SEL_MASK 0xC0U
/** @brief I2C Mode control mask */
#define PCA9420_TOP_CNTL3_MODE_I2C_POS 3U
#define PCA9420_TOP_CNTL3_MODE_I2C_MASK 0x18U
/*
* @brief Mode control selection mask. When this bit is set, the external
* PMIC pins MODESEL0 and MODESEL1 can be used to select the active mode
*/
#define PCA9420_MODECFG_0_X_EN_MODE_SEL_BY_PIN 0x40U
/*
* @brief Mode configuration upon falling edge applied to ON pin. If set,
* the device will switch to mode 0 when a valid falling edge is applied.
* to the ON pin
*/
/** @brief Mode output voltage mask */
#define PCA9420_MODECFG_0_SW1_OUT_MASK 0x3FU
#define PCA9420_MODECFG_0_SW1_OUT_POS 0U
/** @brief SW2_OUT offset and voltage level mask */
#define PCA9420_MODECFG_1_SW2_OUT_MASK 0x3FU
#define PCA9420_MODECFG_1_SW2_OUT_POS 0U
/** @brief LDO1_OUT voltage level mask */
#define PCA9420_MODECFG_2_LDO1_OUT_MASK 0xF0U
#define PCA9420_MODECFG_2_LDO1_OUT_POS 4U
/** @brief SW1 Enable */
#define PCA9420_MODECFG_2_SW1_EN_MASK 0x08U
#define PCA9420_MODECFG_2_SW1_EN_VAL 0x08U
/** @brief SW2 Enable */
#define PCA9420_MODECFG_2_SW2_EN_MASK 0x04U
#define PCA9420_MODECFG_2_SW2_EN_VAL 0x04U
/** @brief LDO1 Enable */
#define PCA9420_MODECFG_2_LDO1_EN_MASK 0x02U
#define PCA9420_MODECFG_2_LDO1_EN_VAL 0x02U
/** @brief LDO2 Enable */
#define PCA9420_MODECFG_2_LDO2_EN_MASK 0x01U
#define PCA9420_MODECFG_2_LDO2_EN_VAL 0x01U
/** @brief LDO2_OUT offset and voltage level mask */
#define PCA9420_MODECFG_3_LDO2_OUT_MASK 0x3FU
#define PCA9420_MODECFG_3_LDO2_OUT_POS 0U
/** @brief SW1 active discharge control */
#define PCA9420_ACT_DISCHARGE_CNTL_SW1_MASK 0x08U
#define PCA9420_ACT_DISCHARGE_CNTL_SW1_POS 4U
/** @brief SW2 active discharge control */
#define PCA9420_ACT_DISCHARGE_CNTL_SW2_MASK 0x04U
#define PCA9420_ACT_DISCHARGE_CNTL_SW2_POS 3U
/** @brief LDO1 active discharge control */
#define PCA9420_ACT_DISCHARGE_CNTL_LDO1_MASK 0x02U
#define PCA9420_ACT_DISCHARGE_CNTL_LDO1_POS 2U
/** @brief LDO2 active discharge control */
#define PCA9420_ACT_DISCHARGE_CNTL_LDO2_MASK 0x01U
#define PCA9420_ACT_DISCHARGE_CNTL_LDO2_POS 1U
/** VIN ILIM resolution, uA/LSB */
#define PCA9420_VIN_ILIM_UA_LSB 170000
/** VIN ILIM minimum value, uA */
#define PCA9420_VIN_ILIM_MIN_UA 85000
/** Number of modes */
#define PCA9420_NUM_MODES 4U
/** Offset applied to MODECFG* registers for a given mode */
#define PCA9420_MODECFG_OFFSET(mode) ((mode) * 4U)
struct regulator_pca9420_desc {
uint8_t enable_reg;
uint8_t enable_mask;
uint8_t enable_val;
uint8_t vsel_reg;
uint8_t vsel_mask;
uint8_t vsel_pos;
uint8_t ad_mask;
uint8_t ad_pos;
int32_t max_ua;
uint8_t num_ranges;
const struct linear_range *ranges;
};
struct regulator_pca9420_common_config {
struct i2c_dt_spec i2c;
int32_t vin_ilim_ua;
bool enable_modesel_pins;
uint8_t asys_uvlo_sel_mv;
};
struct regulator_pca9420_common_data {
regulator_dvs_state_t dvs_state;
};
struct regulator_pca9420_config {
struct regulator_common_config common;
bool enable_inverted;
int32_t modes_uv[4];
const struct regulator_pca9420_desc *desc;
const struct device *parent;
};
struct regulator_pca9420_data {
struct regulator_common_data data;
};
static const struct linear_range buck1_ranges[] = {
LINEAR_RANGE_INIT(500000, 25000U, 0x0U, 0x28U),
LINEAR_RANGE_INIT(1500000, 0U, 0x29U, 0x3E),
LINEAR_RANGE_INIT(1800000, 0U, 0x3FU, 0x3FU),
};
static const struct linear_range buck2_ranges[] = {
LINEAR_RANGE_INIT(1500000, 25000U, 0x0U, 0x18U),
LINEAR_RANGE_INIT(2100000, 0U, 0x19U, 0x1F),
LINEAR_RANGE_INIT(2700000, 25000U, 0x20U, 0x38U),
LINEAR_RANGE_INIT(3300000, 0U, 0x39U, 0x3F),
};
static const struct linear_range ldo1_ranges[] = {
LINEAR_RANGE_INIT(1700000, 25000U, 0x0U, 0x9U),
LINEAR_RANGE_INIT(1900000, 0U, 0x9U, 0xFU),
};
static const struct linear_range ldo2_ranges[] = {
LINEAR_RANGE_INIT(1500000, 25000U, 0x0U, 0x18U),
LINEAR_RANGE_INIT(2100000, 0U, 0x19U, 0x1FU),
LINEAR_RANGE_INIT(2700000, 25000U, 0x20U, 0x38U),
LINEAR_RANGE_INIT(3300000, 0U, 0x39U, 0x3FU),
};
static const struct regulator_pca9420_desc buck1_desc = {
.enable_reg = PCA9420_MODECFG_0_2,
.enable_mask = PCA9420_MODECFG_2_SW1_EN_MASK,
.enable_val = PCA9420_MODECFG_2_SW1_EN_VAL,
.vsel_mask = PCA9420_MODECFG_0_SW1_OUT_MASK,
.vsel_pos = PCA9420_MODECFG_0_SW1_OUT_POS,
.vsel_reg = PCA9420_MODECFG_0_0,
.ad_mask = PCA9420_ACT_DISCHARGE_CNTL_SW1_MASK,
.ad_pos = PCA9420_ACT_DISCHARGE_CNTL_SW1_POS,
.max_ua = 250000,
.ranges = buck1_ranges,
.num_ranges = ARRAY_SIZE(buck1_ranges),
};
static const struct regulator_pca9420_desc buck2_desc = {
.enable_reg = PCA9420_MODECFG_0_2,
.enable_mask = PCA9420_MODECFG_2_SW2_EN_MASK,
.enable_val = PCA9420_MODECFG_2_SW2_EN_VAL,
.vsel_mask = PCA9420_MODECFG_1_SW2_OUT_MASK,
.vsel_pos = PCA9420_MODECFG_1_SW2_OUT_POS,
.vsel_reg = PCA9420_MODECFG_0_1,
.ad_mask = PCA9420_ACT_DISCHARGE_CNTL_SW2_MASK,
.ad_pos = PCA9420_ACT_DISCHARGE_CNTL_SW2_POS,
.max_ua = 500000,
.ranges = buck2_ranges,
.num_ranges = ARRAY_SIZE(buck2_ranges),
};
static const struct regulator_pca9420_desc ldo1_desc = {
.enable_reg = PCA9420_MODECFG_0_2,
.enable_mask = PCA9420_MODECFG_2_LDO1_EN_MASK,
.enable_val = PCA9420_MODECFG_2_LDO1_EN_VAL,
.vsel_mask = PCA9420_MODECFG_2_LDO1_OUT_MASK,
.vsel_pos = PCA9420_MODECFG_2_LDO1_OUT_POS,
.vsel_reg = PCA9420_MODECFG_0_2,
.ad_mask = PCA9420_ACT_DISCHARGE_CNTL_LDO1_MASK,
.ad_pos = PCA9420_ACT_DISCHARGE_CNTL_LDO1_POS,
.max_ua = 1000,
.ranges = ldo1_ranges,
.num_ranges = ARRAY_SIZE(ldo1_ranges),
};
static const struct regulator_pca9420_desc ldo2_desc = {
.enable_reg = PCA9420_MODECFG_0_2,
.enable_mask = PCA9420_MODECFG_2_LDO2_EN_MASK,
.enable_val = PCA9420_MODECFG_2_LDO2_EN_VAL,
.vsel_reg = PCA9420_MODECFG_0_3,
.vsel_mask = PCA9420_MODECFG_3_LDO2_OUT_MASK,
.vsel_pos = PCA9420_MODECFG_3_LDO2_OUT_POS,
.ad_mask = PCA9420_ACT_DISCHARGE_CNTL_LDO2_MASK,
.ad_pos = PCA9420_ACT_DISCHARGE_CNTL_LDO2_POS,
.max_ua = 250000,
.ranges = ldo2_ranges,
.num_ranges = ARRAY_SIZE(ldo2_ranges),
};
static unsigned int regulator_pca9420_count_voltages(const struct device *dev)
{
const struct regulator_pca9420_config *config = dev->config;
return linear_range_group_values_count(config->desc->ranges,
config->desc->num_ranges);
}
static int regulator_pca9420_list_voltage(const struct device *dev,
unsigned int idx, int32_t *volt_uv)
{
const struct regulator_pca9420_config *config = dev->config;
return linear_range_group_get_value(config->desc->ranges,
config->desc->num_ranges, idx,
volt_uv);
}
static int regulator_pca9420_set_voltage(const struct device *dev,
int32_t min_uv, int32_t max_uv)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
struct regulator_pca9420_common_data *cdata = config->parent->data;
uint16_t idx;
int ret;
ret = linear_range_group_get_win_index(config->desc->ranges,
config->desc->num_ranges, min_uv,
max_uv, &idx);
if (ret == -EINVAL) {
return ret;
}
idx <<= config->desc->vsel_pos;
return i2c_reg_update_byte_dt(&cconfig->i2c, config->desc->vsel_reg +
PCA9420_MODECFG_OFFSET(cdata->dvs_state),
config->desc->vsel_mask, (uint8_t)idx);
}
static int regulator_pca9420_get_voltage(const struct device *dev,
int32_t *volt_uv)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
struct regulator_pca9420_common_data *cdata = config->parent->data;
int ret;
uint8_t raw_reg;
ret = i2c_reg_read_byte_dt(&cconfig->i2c, config->desc->vsel_reg +
PCA9420_MODECFG_OFFSET(cdata->dvs_state),
&raw_reg);
if (ret < 0) {
return ret;
}
raw_reg = (raw_reg & config->desc->vsel_mask) >> config->desc->vsel_pos;
return linear_range_group_get_value(config->desc->ranges,
config->desc->num_ranges, raw_reg,
volt_uv);
}
static int regulator_pca9420_get_current_limit(const struct device *dev,
int32_t *curr_ua)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
if (cconfig->vin_ilim_ua == 0U) {
*curr_ua = config->desc->max_ua;
} else {
*curr_ua = MIN(config->desc->max_ua, cconfig->vin_ilim_ua);
}
return 0;
}
static int regulator_pca9420_set_active_discharge(const struct device *dev,
bool active_discharge)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
uint8_t dis_val;
dis_val = (!active_discharge) << config->desc->ad_pos;
return i2c_reg_update_byte_dt(&cconfig->i2c, PCA9420_ACT_DISCHARGE_CNTL,
config->desc->ad_mask, dis_val);
}
static int regulator_pca9420_get_active_discharge(const struct device *dev,
bool *active_discharge)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
uint8_t raw_reg;
int ret;
ret = i2c_reg_read_byte_dt(&cconfig->i2c, PCA9420_ACT_DISCHARGE_CNTL, &raw_reg);
if (ret < 0) {
return ret;
}
*active_discharge = !((raw_reg & config->desc->ad_mask) >> config->desc->ad_pos);
return 0;
}
static int regulator_pca9420_enable(const struct device *dev)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
struct regulator_pca9420_common_data *cdata = config->parent->data;
uint8_t en_val;
en_val = config->enable_inverted ? 0 : config->desc->enable_val;
return i2c_reg_update_byte_dt(&cconfig->i2c, config->desc->enable_reg
+ PCA9420_MODECFG_OFFSET(cdata->dvs_state),
config->desc->enable_mask, en_val);
}
static int regulator_pca9420_disable(const struct device *dev)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
struct regulator_pca9420_common_data *cdata = config->parent->data;
uint8_t dis_val;
dis_val = config->enable_inverted ? config->desc->enable_val : 0;
return i2c_reg_update_byte_dt(&cconfig->i2c, config->desc->enable_reg
+ PCA9420_MODECFG_OFFSET(cdata->dvs_state),
config->desc->enable_mask, dis_val);
}
static const struct regulator_driver_api api = {
.enable = regulator_pca9420_enable,
.disable = regulator_pca9420_disable,
.count_voltages = regulator_pca9420_count_voltages,
.list_voltage = regulator_pca9420_list_voltage,
.set_voltage = regulator_pca9420_set_voltage,
.get_voltage = regulator_pca9420_get_voltage,
.get_current_limit = regulator_pca9420_get_current_limit,
.set_active_discharge = regulator_pca9420_set_active_discharge,
.get_active_discharge = regulator_pca9420_get_active_discharge,
};
static int regulator_pca9420_init(const struct device *dev)
{
const struct regulator_pca9420_config *config = dev->config;
const struct regulator_pca9420_common_config *cconfig = config->parent->config;
regulator_common_data_init(dev);
if (!device_is_ready(config->parent)) {
return -ENODEV;
}
/* configure mode voltages */
for (uint8_t i = 0U; i < ARRAY_SIZE(config->modes_uv); i++) {
int ret;
if (config->modes_uv[i] == 0) {
/* disable mode if voltage is 0 */
ret = i2c_reg_update_byte_dt(
&cconfig->i2c,
config->desc->enable_reg + PCA9420_MODECFG_OFFSET(i),
config->desc->enable_mask, 0U);
if (ret < 0) {
return ret;
}
} else if (config->modes_uv[i] > 0) {
uint16_t idx;
/* program mode voltage */
ret = linear_range_group_get_win_index(
config->desc->ranges, config->desc->num_ranges,
config->modes_uv[i], config->modes_uv[i], &idx);
if (ret == -EINVAL) {
return ret;
}
idx <<= config->desc->vsel_pos;
ret = i2c_reg_update_byte_dt(
&cconfig->i2c,
config->desc->vsel_reg + PCA9420_MODECFG_OFFSET(i),
config->desc->vsel_mask, (uint8_t)idx);
if (ret < 0) {
return ret;
}
}
}
return regulator_common_init(dev, false);
}
int regulator_pca9420_dvs_state_set(const struct device *dev,
regulator_dvs_state_t state)
{
const struct regulator_pca9420_common_config *config = dev->config;
struct regulator_pca9420_common_data *data = dev->data;
int ret;
if (state >= PCA9420_NUM_MODES) {
return -ENOTSUP;
}
if (config->enable_modesel_pins) {
/*
* The user cannot set DVS state via this API,
* but they may want to query/set voltages for another mode.
* Return -EPERM to indicate change failed, but change the
* dvs_state variable so the user can access the alternative
* dvs mode settings.
*/
data->dvs_state = state;
return -EPERM;
}
ret = i2c_reg_update_byte_dt(&config->i2c, PCA9420_TOP_CNTL3,
PCA9420_TOP_CNTL3_MODE_I2C_MASK,
state << PCA9420_TOP_CNTL3_MODE_I2C_POS);
if (ret < 0) {
return ret;
}
/* Record new DVS state */
data->dvs_state = state;
return 0;
}
static const struct regulator_parent_driver_api parent_api = {
.dvs_state_set = regulator_pca9420_dvs_state_set,
};
static int regulator_pca9420_common_init(const struct device *dev)
{
const struct regulator_pca9420_common_config *config = dev->config;
uint8_t reg_val = PCA9420_TOP_CNTL0_VIN_ILIM_SEL_DISABLED;
int ret;
if (!device_is_ready(config->i2c.bus)) {
return -ENODEV;
}
if (config->enable_modesel_pins) {
/* enable MODESEL0/1 pins for each mode */
for (uint8_t i = 0U; i < PCA9420_NUM_MODES; i++) {
ret = i2c_reg_update_byte_dt(
&config->i2c,
PCA9420_MODECFG_0_0 +
PCA9420_MODECFG_OFFSET(i),
PCA9420_MODECFG_0_X_EN_MODE_SEL_BY_PIN,
PCA9420_MODECFG_0_X_EN_MODE_SEL_BY_PIN);
if (ret < 0) {
return ret;
}
}
}
/* configure VIN current limit */
if (config->vin_ilim_ua != 0U) {
reg_val = (config->vin_ilim_ua - PCA9420_VIN_ILIM_MIN_UA) /
PCA9420_VIN_ILIM_UA_LSB;
}
ret = i2c_reg_update_byte_dt(
&config->i2c, PCA9420_TOP_CNTL0,
PCA9420_TOP_CNTL0_VIN_ILIM_SEL_MASK,
reg_val << PCA9420_TOP_CNTL0_VIN_ILIM_SEL_POS);
if (ret != 0) {
return ret;
}
/* configure ASYS UVLO threshold */
return i2c_reg_update_byte_dt(&config->i2c, PCA9420_TOP_CNTL2,
PCA9420_TOP_CNTL2_ASYS_UVLO_SEL_MASK,
config->asys_uvlo_sel_mv <<
PCA9420_TOP_CNTL2_ASYS_UVLO_SEL_POS);
}
#define REGULATOR_PCA9420_DEFINE(node_id, id, name, _parent) \
static struct regulator_pca9420_data data_##id; \
\
static const struct regulator_pca9420_config config_##id = { \
.common = REGULATOR_DT_COMMON_CONFIG_INIT(node_id), \
.enable_inverted = DT_PROP(node_id, enable_inverted), \
.modes_uv = { \
DT_PROP_OR(node_id, nxp_mode0_microvolt, -1), \
DT_PROP_OR(node_id, nxp_mode1_microvolt, -1), \
DT_PROP_OR(node_id, nxp_mode2_microvolt, -1), \
DT_PROP_OR(node_id, nxp_mode3_microvolt, -1), \
}, \
.desc = &name ## _desc, \
.parent = _parent, \
}; \
\
DEVICE_DT_DEFINE(node_id, regulator_pca9420_init, NULL, &data_##id, \
&config_##id, POST_KERNEL, \
CONFIG_REGULATOR_PCA9420_INIT_PRIORITY, &api);
#define REGULATOR_PCA9420_DEFINE_COND(inst, child, parent) \
COND_CODE_1(DT_NODE_EXISTS(DT_INST_CHILD(inst, child)), \
(REGULATOR_PCA9420_DEFINE(DT_INST_CHILD(inst, child), \
child ## inst, child, parent)), \
())
#define REGULATOR_PCA9420_DEFINE_ALL(inst) \
static const struct regulator_pca9420_common_config config_##inst = { \
.i2c = I2C_DT_SPEC_INST_GET(inst), \
.vin_ilim_ua = DT_INST_PROP(inst, nxp_vin_ilim_microamp), \
.enable_modesel_pins = \
DT_INST_PROP(inst, nxp_enable_modesel_pins), \
.asys_uvlo_sel_mv = \
DT_INST_ENUM_IDX(inst, nxp_asys_uvlo_sel_millivolt), \
}; \
\
static struct regulator_pca9420_common_data data_##inst; \
\
DEVICE_DT_INST_DEFINE(inst, regulator_pca9420_common_init, NULL, \
&data_##inst, \
&config_##inst, POST_KERNEL, \
CONFIG_REGULATOR_PCA9420_COMMON_INIT_PRIORITY, \
&parent_api); \
\
REGULATOR_PCA9420_DEFINE_COND(inst, buck1, DEVICE_DT_INST_GET(inst)) \
REGULATOR_PCA9420_DEFINE_COND(inst, buck2, DEVICE_DT_INST_GET(inst)) \
REGULATOR_PCA9420_DEFINE_COND(inst, ldo1, DEVICE_DT_INST_GET(inst)) \
REGULATOR_PCA9420_DEFINE_COND(inst, ldo2, DEVICE_DT_INST_GET(inst))
DT_INST_FOREACH_STATUS_OKAY(REGULATOR_PCA9420_DEFINE_ALL)
Reference in New Issue View Git Blame Copy Permalink