246 lines
7.6 KiB
C
246 lines
7.6 KiB
C
/*
|
|
* Copyright (c) 2022 Vestas Wind Systems A/S
|
|
* Copyright (c) 2021 Alexander Wachter
|
|
* Copyright (c) 2022 Kamil Serwus
|
|
* Copyright (c) 2023 Sebastian Schlupp
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#include <zephyr/drivers/can.h>
|
|
#include <zephyr/drivers/can/can_mcan.h>
|
|
#include <zephyr/drivers/pinctrl.h>
|
|
#include <zephyr/irq.h>
|
|
#include <zephyr/kernel.h>
|
|
#include <zephyr/logging/log.h>
|
|
#include <soc.h>
|
|
|
|
LOG_MODULE_REGISTER(can_sam0, CONFIG_CAN_LOG_LEVEL);
|
|
|
|
#define DT_DRV_COMPAT atmel_sam0_can
|
|
|
|
struct can_sam0_config {
|
|
mm_reg_t base;
|
|
mem_addr_t mram;
|
|
void (*config_irq)(void);
|
|
const struct pinctrl_dev_config *pcfg;
|
|
volatile uint32_t *mclk;
|
|
uint32_t mclk_mask;
|
|
uint16_t gclk_core_id;
|
|
int divider;
|
|
};
|
|
|
|
static int can_sam0_read_reg(const struct device *dev, uint16_t reg, uint32_t *val)
|
|
{
|
|
const struct can_mcan_config *mcan_config = dev->config;
|
|
const struct can_sam0_config *sam_config = mcan_config->custom;
|
|
|
|
return can_mcan_sys_read_reg(sam_config->base, reg, val);
|
|
}
|
|
|
|
static int can_sam0_write_reg(const struct device *dev, uint16_t reg, uint32_t val)
|
|
{
|
|
const struct can_mcan_config *mcan_config = dev->config;
|
|
const struct can_sam0_config *sam_config = mcan_config->custom;
|
|
|
|
switch (reg) {
|
|
case CAN_MCAN_ILS:
|
|
/* All interrupts are assigned to MCAN_INT0 */
|
|
val = 0;
|
|
break;
|
|
case CAN_MCAN_ILE:
|
|
/* SAM0 has only one line to handle interrupts */
|
|
val = CAN_MCAN_ILE_EINT0;
|
|
break;
|
|
default:
|
|
/* No field remap needed */
|
|
break;
|
|
};
|
|
|
|
return can_mcan_sys_write_reg(sam_config->base, reg, val);
|
|
}
|
|
|
|
static int can_sam0_read_mram(const struct device *dev, uint16_t offset, void *dst, size_t len)
|
|
{
|
|
const struct can_mcan_config *mcan_config = dev->config;
|
|
const struct can_sam0_config *sam_config = mcan_config->custom;
|
|
|
|
return can_mcan_sys_read_mram(sam_config->mram, offset, dst, len);
|
|
}
|
|
|
|
static int can_sam0_write_mram(const struct device *dev, uint16_t offset, const void *src,
|
|
size_t len)
|
|
{
|
|
const struct can_mcan_config *mcan_config = dev->config;
|
|
const struct can_sam0_config *sam_config = mcan_config->custom;
|
|
|
|
return can_mcan_sys_write_mram(sam_config->mram, offset, src, len);
|
|
}
|
|
|
|
static int can_sam0_clear_mram(const struct device *dev, uint16_t offset, size_t len)
|
|
{
|
|
const struct can_mcan_config *mcan_config = dev->config;
|
|
const struct can_sam0_config *sam_config = mcan_config->custom;
|
|
|
|
return can_mcan_sys_clear_mram(sam_config->mram, offset, len);
|
|
}
|
|
|
|
void can_sam0_line_x_isr(const struct device *dev)
|
|
{
|
|
can_mcan_line_0_isr(dev);
|
|
can_mcan_line_1_isr(dev);
|
|
}
|
|
|
|
static int can_sam0_get_core_clock(const struct device *dev, uint32_t *rate)
|
|
{
|
|
const struct can_mcan_config *mcan_cfg = dev->config;
|
|
const struct can_sam0_config *sam_cfg = mcan_cfg->custom;
|
|
|
|
#if defined(CONFIG_SOC_SERIES_SAME51) || defined(CONFIG_SOC_SERIES_SAME54)
|
|
/*DFFL has to be used as clock source for the ATSAME51/54 family of SoCs*/
|
|
*rate = SOC_ATMEL_SAM0_DFLL48_FREQ_HZ / (sam_cfg->divider);
|
|
#elif defined(CONFIG_SOC_SERIES_SAMC21)
|
|
/*OSC48M has to be used as clock source for the ATSAMC21 family of SoCs*/
|
|
*rate = SOC_ATMEL_SAM0_OSC48M_FREQ_HZ / (sam_cfg->divider);
|
|
#endif
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void can_sam0_clock_enable(const struct can_sam0_config *cfg)
|
|
{
|
|
/* Enable the GLCK7 with DIV*/
|
|
#if defined(CONFIG_SOC_SERIES_SAME51) || defined(CONFIG_SOC_SERIES_SAME54)
|
|
/*DFFL has to be used as clock source for the ATSAME51/54 family of SoCs*/
|
|
GCLK->GENCTRL[7].reg = GCLK_GENCTRL_SRC(GCLK_GENCTRL_SRC_DFLL)
|
|
| GCLK_GENCTRL_DIV(cfg->divider)
|
|
| GCLK_GENCTRL_GENEN;
|
|
#elif defined(CONFIG_SOC_SERIES_SAMC21)
|
|
/*OSC48M has to be used as clock source for the ATSAMC21 family of SoCs*/
|
|
GCLK->GENCTRL[7].reg = GCLK_GENCTRL_SRC(GCLK_GENCTRL_SRC_OSC48M)
|
|
| GCLK_GENCTRL_DIV(cfg->divider)
|
|
| GCLK_GENCTRL_GENEN;
|
|
#endif
|
|
|
|
/* Route channel */
|
|
GCLK->PCHCTRL[cfg->gclk_core_id].reg = GCLK_PCHCTRL_GEN_GCLK7
|
|
| GCLK_PCHCTRL_CHEN;
|
|
|
|
/* Enable CAN clock in MCLK */
|
|
*cfg->mclk |= cfg->mclk_mask;
|
|
}
|
|
|
|
static int can_sam0_init(const struct device *dev)
|
|
{
|
|
const struct can_mcan_config *mcan_cfg = dev->config;
|
|
const struct can_sam0_config *sam_cfg = mcan_cfg->custom;
|
|
int ret;
|
|
|
|
can_sam0_clock_enable(sam_cfg);
|
|
|
|
ret = pinctrl_apply_state(sam_cfg->pcfg, PINCTRL_STATE_DEFAULT);
|
|
if (ret < 0) {
|
|
LOG_ERR("failed to apply pinctrl");
|
|
return ret;
|
|
}
|
|
|
|
ret = can_mcan_configure_mram(dev, 0U, sam_cfg->mram);
|
|
if (ret != 0) {
|
|
LOG_ERR("failed to configure message ram");
|
|
return ret;
|
|
}
|
|
|
|
ret = can_mcan_init(dev);
|
|
if (ret != 0) {
|
|
LOG_ERR("failed to mcan init");
|
|
return ret;
|
|
}
|
|
|
|
sam_cfg->config_irq();
|
|
|
|
return ret;
|
|
}
|
|
|
|
static const struct can_driver_api can_sam0_driver_api = {
|
|
.get_capabilities = can_mcan_get_capabilities,
|
|
.start = can_mcan_start,
|
|
.stop = can_mcan_stop,
|
|
.set_mode = can_mcan_set_mode,
|
|
.set_timing = can_mcan_set_timing,
|
|
.send = can_mcan_send,
|
|
.add_rx_filter = can_mcan_add_rx_filter,
|
|
.remove_rx_filter = can_mcan_remove_rx_filter,
|
|
.get_state = can_mcan_get_state,
|
|
#ifdef CONFIG_CAN_MANUAL_RECOVERY_MODE
|
|
.recover = can_mcan_recover,
|
|
#endif /* CONFIG_CAN_MANUAL_RECOVERY_MODE */
|
|
.get_core_clock = can_sam0_get_core_clock,
|
|
.get_max_filters = can_mcan_get_max_filters,
|
|
.set_state_change_callback = can_mcan_set_state_change_callback,
|
|
.timing_min = CAN_MCAN_TIMING_MIN_INITIALIZER,
|
|
.timing_max = CAN_MCAN_TIMING_MAX_INITIALIZER,
|
|
#ifdef CONFIG_CAN_FD_MODE
|
|
.set_timing_data = can_mcan_set_timing_data,
|
|
.timing_data_min = CAN_MCAN_TIMING_DATA_MIN_INITIALIZER,
|
|
.timing_data_max = CAN_MCAN_TIMING_DATA_MAX_INITIALIZER,
|
|
#endif /* CONFIG_CAN_FD_MODE */
|
|
};
|
|
|
|
static const struct can_mcan_ops can_sam0_ops = {
|
|
.read_reg = can_sam0_read_reg,
|
|
.write_reg = can_sam0_write_reg,
|
|
.read_mram = can_sam0_read_mram,
|
|
.write_mram = can_sam0_write_mram,
|
|
.clear_mram = can_sam0_clear_mram,
|
|
};
|
|
|
|
#define CAN_SAM0_IRQ_CFG_FUNCTION(inst) \
|
|
static void config_can_##inst##_irq(void) \
|
|
{ \
|
|
LOG_DBG("Enable CAN##inst## IRQ"); \
|
|
IRQ_CONNECT(DT_INST_IRQ_BY_NAME(inst, int0, irq), \
|
|
DT_INST_IRQ_BY_NAME(inst, int0, priority), can_sam0_line_x_isr, \
|
|
DEVICE_DT_INST_GET(inst), 0); \
|
|
irq_enable(DT_INST_IRQ_BY_NAME(inst, int0, irq)); \
|
|
}
|
|
|
|
#define CAN_SAM0_CFG_INST(inst) \
|
|
CAN_MCAN_DT_INST_CALLBACKS_DEFINE(inst, can_sam0_cbs_##inst); \
|
|
CAN_MCAN_DT_INST_MRAM_DEFINE(inst, can_sam0_mram_##inst); \
|
|
\
|
|
static const struct can_sam0_config can_sam0_cfg_##inst = { \
|
|
.base = CAN_MCAN_DT_INST_MCAN_ADDR(inst), \
|
|
.mram = (mem_addr_t)POINTER_TO_UINT(&can_sam0_mram_##inst), \
|
|
.mclk = (volatile uint32_t *)MCLK_MASK_DT_INT_REG_ADDR(inst), \
|
|
.mclk_mask = BIT(DT_INST_CLOCKS_CELL_BY_NAME(inst, mclk, bit)), \
|
|
.gclk_core_id = DT_INST_CLOCKS_CELL_BY_NAME(inst, gclk, periph_ch), \
|
|
.divider = DT_INST_PROP(inst, divider), \
|
|
.pcfg = PINCTRL_DT_INST_DEV_CONFIG_GET(inst), \
|
|
.config_irq = config_can_##inst##_irq, \
|
|
}; \
|
|
\
|
|
static const struct can_mcan_config can_mcan_cfg_##inst = \
|
|
CAN_MCAN_DT_CONFIG_INST_GET(inst, &can_sam0_cfg_##inst, &can_sam0_ops, \
|
|
&can_sam0_cbs_##inst);
|
|
|
|
#define CAN_SAM0_DATA_INST(inst) \
|
|
static struct can_mcan_data can_mcan_data_##inst = \
|
|
CAN_MCAN_DATA_INITIALIZER(NULL);
|
|
|
|
#define CAN_SAM0_DEVICE_INST(inst) \
|
|
CAN_DEVICE_DT_INST_DEFINE(inst, can_sam0_init, NULL, \
|
|
&can_mcan_data_##inst, \
|
|
&can_mcan_cfg_##inst, \
|
|
POST_KERNEL, CONFIG_CAN_INIT_PRIORITY, \
|
|
&can_sam0_driver_api);
|
|
|
|
#define CAN_SAM0_INST(inst) \
|
|
CAN_MCAN_DT_INST_BUILD_ASSERT_MRAM_CFG(inst); \
|
|
PINCTRL_DT_INST_DEFINE(inst); \
|
|
CAN_SAM0_IRQ_CFG_FUNCTION(inst) \
|
|
CAN_SAM0_CFG_INST(inst) \
|
|
CAN_SAM0_DATA_INST(inst) \
|
|
CAN_SAM0_DEVICE_INST(inst)
|
|
|
|
DT_INST_FOREACH_STATUS_OKAY(CAN_SAM0_INST)
|