338 lines
8.5 KiB
C
338 lines
8.5 KiB
C
/*
|
|
* Copyright (c) 2019 Brett Witherspoon
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#define DT_DRV_COMPAT ti_cc13xx_cc26xx_spi
|
|
|
|
#define LOG_LEVEL CONFIG_SPI_LOG_LEVEL
|
|
#include <zephyr/logging/log.h>
|
|
LOG_MODULE_REGISTER(spi_cc13xx_cc26xx);
|
|
|
|
#include <zephyr/drivers/spi.h>
|
|
#include <zephyr/drivers/spi/rtio.h>
|
|
#include <zephyr/drivers/pinctrl.h>
|
|
#include <zephyr/pm/device.h>
|
|
#include <zephyr/pm/policy.h>
|
|
|
|
#include <driverlib/prcm.h>
|
|
#include <driverlib/ssi.h>
|
|
|
|
#include <ti/drivers/Power.h>
|
|
#include <ti/drivers/power/PowerCC26X2.h>
|
|
|
|
#include "spi_context.h"
|
|
|
|
struct spi_cc13xx_cc26xx_config {
|
|
uint32_t base;
|
|
const struct pinctrl_dev_config *pcfg;
|
|
};
|
|
|
|
struct spi_cc13xx_cc26xx_data {
|
|
struct spi_context ctx;
|
|
};
|
|
|
|
#define CPU_FREQ DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
|
|
|
|
static int spi_cc13xx_cc26xx_configure(const struct device *dev,
|
|
const struct spi_config *config)
|
|
{
|
|
const struct spi_cc13xx_cc26xx_config *cfg = dev->config;
|
|
struct spi_cc13xx_cc26xx_data *data = dev->data;
|
|
struct spi_context *ctx = &data->ctx;
|
|
uint32_t prot;
|
|
int ret;
|
|
|
|
if (spi_context_configured(ctx, config)) {
|
|
return 0;
|
|
}
|
|
|
|
if (config->operation & SPI_HALF_DUPLEX) {
|
|
LOG_ERR("Half-duplex not supported");
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
/* Slave mode has not been implemented */
|
|
if (SPI_OP_MODE_GET(config->operation) != SPI_OP_MODE_MASTER) {
|
|
LOG_ERR("Slave mode is not supported");
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
/* Word sizes other than 8 bits has not been implemented */
|
|
if (SPI_WORD_SIZE_GET(config->operation) != 8) {
|
|
LOG_ERR("Word sizes other than 8 bits are not supported");
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
if (config->operation & SPI_TRANSFER_LSB) {
|
|
LOG_ERR("Transfer LSB first mode is not supported");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (IS_ENABLED(CONFIG_SPI_EXTENDED_MODES) &&
|
|
(config->operation & SPI_LINES_MASK) != SPI_LINES_SINGLE) {
|
|
LOG_ERR("Multiple lines are not supported");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (config->operation & SPI_CS_ACTIVE_HIGH && !spi_cs_is_gpio(config)) {
|
|
LOG_ERR("Active high CS requires emulation through a GPIO line.");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (config->frequency < 2000000) {
|
|
LOG_ERR("Frequencies lower than 2 MHz are not supported");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (2 * config->frequency > CPU_FREQ) {
|
|
LOG_ERR("Frequency greater than supported in master mode");
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (SPI_MODE_GET(config->operation) & SPI_MODE_CPOL) {
|
|
if (SPI_MODE_GET(config->operation) & SPI_MODE_CPHA) {
|
|
prot = SSI_FRF_MOTO_MODE_3;
|
|
} else {
|
|
prot = SSI_FRF_MOTO_MODE_2;
|
|
}
|
|
} else {
|
|
if (SPI_MODE_GET(config->operation) & SPI_MODE_CPHA) {
|
|
prot = SSI_FRF_MOTO_MODE_1;
|
|
} else {
|
|
prot = SSI_FRF_MOTO_MODE_0;
|
|
}
|
|
}
|
|
|
|
ret = pinctrl_apply_state(cfg->pcfg, PINCTRL_STATE_DEFAULT);
|
|
if (ret < 0) {
|
|
LOG_ERR("applying SPI pinctrl state failed");
|
|
return ret;
|
|
}
|
|
|
|
ctx->config = config;
|
|
|
|
/* Disable SSI before making configuration changes */
|
|
SSIDisable(cfg->base);
|
|
|
|
/* Configure SSI */
|
|
SSIConfigSetExpClk(cfg->base, CPU_FREQ, prot,
|
|
SSI_MODE_MASTER, config->frequency, 8);
|
|
|
|
if (SPI_MODE_GET(config->operation) & SPI_MODE_LOOP) {
|
|
sys_set_bit(cfg->base + SSI_O_CR1, 0);
|
|
}
|
|
|
|
/* Re-enable SSI after making configuration changes */
|
|
SSIEnable(cfg->base);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int spi_cc13xx_cc26xx_transceive(const struct device *dev,
|
|
const struct spi_config *config,
|
|
const struct spi_buf_set *tx_bufs,
|
|
const struct spi_buf_set *rx_bufs)
|
|
{
|
|
const struct spi_cc13xx_cc26xx_config *cfg = dev->config;
|
|
struct spi_cc13xx_cc26xx_data *data = dev->data;
|
|
struct spi_context *ctx = &data->ctx;
|
|
uint32_t txd, rxd;
|
|
int err;
|
|
|
|
spi_context_lock(ctx, false, NULL, NULL, config);
|
|
pm_policy_state_lock_get(PM_STATE_STANDBY, PM_ALL_SUBSTATES);
|
|
|
|
err = spi_cc13xx_cc26xx_configure(dev, config);
|
|
if (err) {
|
|
goto done;
|
|
}
|
|
|
|
spi_context_buffers_setup(ctx, tx_bufs, rx_bufs, 1);
|
|
|
|
spi_context_cs_control(ctx, true);
|
|
|
|
do {
|
|
if (spi_context_tx_buf_on(ctx)) {
|
|
txd = *ctx->tx_buf;
|
|
} else {
|
|
txd = 0U;
|
|
}
|
|
|
|
SSIDataPut(cfg->base, txd);
|
|
|
|
spi_context_update_tx(ctx, 1, 1);
|
|
|
|
SSIDataGet(cfg->base, &rxd);
|
|
|
|
if (spi_context_rx_buf_on(ctx)) {
|
|
*ctx->rx_buf = rxd;
|
|
}
|
|
|
|
spi_context_update_rx(ctx, 1, 1);
|
|
} while (spi_context_tx_on(ctx) || spi_context_rx_on(ctx));
|
|
|
|
spi_context_cs_control(ctx, false);
|
|
|
|
done:
|
|
pm_policy_state_lock_put(PM_STATE_STANDBY, PM_ALL_SUBSTATES);
|
|
spi_context_release(ctx, err);
|
|
return err;
|
|
}
|
|
|
|
static int spi_cc13xx_cc26xx_release(const struct device *dev,
|
|
const struct spi_config *config)
|
|
{
|
|
const struct spi_cc13xx_cc26xx_config *cfg = dev->config;
|
|
struct spi_cc13xx_cc26xx_data *data = dev->data;
|
|
struct spi_context *ctx = &data->ctx;
|
|
|
|
if (!spi_context_configured(ctx, config)) {
|
|
return -EINVAL;
|
|
}
|
|
|
|
if (SSIBusy(cfg->base)) {
|
|
return -EBUSY;
|
|
}
|
|
|
|
spi_context_unlock_unconditionally(ctx);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM_DEVICE
|
|
static int spi_cc13xx_cc26xx_pm_action(const struct device *dev,
|
|
enum pm_device_action action)
|
|
{
|
|
const struct spi_cc13xx_cc26xx_config *config = dev->config;
|
|
|
|
switch (action) {
|
|
case PM_DEVICE_ACTION_RESUME:
|
|
if (config->base == DT_INST_REG_ADDR(0)) {
|
|
Power_setDependency(PowerCC26XX_PERIPH_SSI0);
|
|
} else {
|
|
Power_setDependency(PowerCC26XX_PERIPH_SSI1);
|
|
}
|
|
break;
|
|
case PM_DEVICE_ACTION_SUSPEND:
|
|
SSIDisable(config->base);
|
|
/*
|
|
* Release power dependency
|
|
*/
|
|
if (config->base == DT_INST_REG_ADDR(0)) {
|
|
Power_releaseDependency(PowerCC26XX_PERIPH_SSI0);
|
|
} else {
|
|
Power_releaseDependency(PowerCC26XX_PERIPH_SSI1);
|
|
}
|
|
break;
|
|
default:
|
|
return -ENOTSUP;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif /* CONFIG_PM_DEVICE */
|
|
|
|
|
|
static const struct spi_driver_api spi_cc13xx_cc26xx_driver_api = {
|
|
.transceive = spi_cc13xx_cc26xx_transceive,
|
|
.release = spi_cc13xx_cc26xx_release,
|
|
#ifdef CONFIG_SPI_RTIO
|
|
.iodev_submit = spi_rtio_iodev_default_submit,
|
|
#endif
|
|
};
|
|
|
|
#ifdef CONFIG_PM
|
|
#define SPI_CC13XX_CC26XX_POWER_SPI(n) \
|
|
do { \
|
|
/* Set Power dependencies & constraints */ \
|
|
if (DT_INST_REG_ADDR(n) == 0x40000000) { \
|
|
Power_setDependency(PowerCC26XX_PERIPH_SSI0); \
|
|
} else { \
|
|
Power_setDependency(PowerCC26XX_PERIPH_SSI1); \
|
|
} \
|
|
} while (false)
|
|
#else
|
|
#define SPI_CC13XX_CC26XX_POWER_SPI(n) \
|
|
do { \
|
|
uint32_t domain, periph; \
|
|
\
|
|
/* Enable UART power domain */ \
|
|
if (DT_INST_REG_ADDR(n) == 0x40000000) { \
|
|
domain = PRCM_DOMAIN_SERIAL; \
|
|
periph = PRCM_PERIPH_SSI0; \
|
|
} else { \
|
|
domain = PRCM_DOMAIN_PERIPH; \
|
|
periph = PRCM_PERIPH_SSI1; \
|
|
} \
|
|
/* Enable SSI##n power domain */ \
|
|
PRCMPowerDomainOn(domain); \
|
|
\
|
|
/* Enable SSI##n peripherals */ \
|
|
PRCMPeripheralRunEnable(periph); \
|
|
PRCMPeripheralSleepEnable(periph); \
|
|
PRCMPeripheralDeepSleepEnable(periph); \
|
|
\
|
|
/* Load PRCM settings */ \
|
|
PRCMLoadSet(); \
|
|
while (!PRCMLoadGet()) { \
|
|
continue; \
|
|
} \
|
|
\
|
|
/* SSI should not be accessed until power domain is on. */\
|
|
while (PRCMPowerDomainsAllOn(domain) != \
|
|
PRCM_DOMAIN_POWER_ON) { \
|
|
continue; \
|
|
} \
|
|
} while (false)
|
|
#endif
|
|
|
|
#define SPI_CC13XX_CC26XX_DEVICE_INIT(n) \
|
|
PM_DEVICE_DT_INST_DEFINE(n, spi_cc13xx_cc26xx_pm_action); \
|
|
\
|
|
DEVICE_DT_INST_DEFINE(n, \
|
|
spi_cc13xx_cc26xx_init_##n, \
|
|
PM_DEVICE_DT_INST_GET(n), \
|
|
&spi_cc13xx_cc26xx_data_##n, &spi_cc13xx_cc26xx_config_##n, \
|
|
POST_KERNEL, CONFIG_SPI_INIT_PRIORITY, \
|
|
&spi_cc13xx_cc26xx_driver_api)
|
|
|
|
#define SPI_CC13XX_CC26XX_INIT_FUNC(n) \
|
|
static int spi_cc13xx_cc26xx_init_##n(const struct device *dev) \
|
|
{ \
|
|
struct spi_cc13xx_cc26xx_data *data = dev->data; \
|
|
int err; \
|
|
SPI_CC13XX_CC26XX_POWER_SPI(n); \
|
|
\
|
|
err = spi_context_cs_configure_all(&data->ctx); \
|
|
if (err < 0) { \
|
|
return err; \
|
|
} \
|
|
\
|
|
spi_context_unlock_unconditionally(&data->ctx); \
|
|
\
|
|
return 0; \
|
|
}
|
|
|
|
#define SPI_CC13XX_CC26XX_INIT(n) \
|
|
PINCTRL_DT_INST_DEFINE(n); \
|
|
SPI_CC13XX_CC26XX_INIT_FUNC(n) \
|
|
\
|
|
static const struct spi_cc13xx_cc26xx_config \
|
|
spi_cc13xx_cc26xx_config_##n = { \
|
|
.base = DT_INST_REG_ADDR(n), \
|
|
.pcfg = PINCTRL_DT_INST_DEV_CONFIG_GET(n) \
|
|
}; \
|
|
\
|
|
static struct spi_cc13xx_cc26xx_data \
|
|
spi_cc13xx_cc26xx_data_##n = { \
|
|
SPI_CONTEXT_INIT_LOCK(spi_cc13xx_cc26xx_data_##n, ctx), \
|
|
SPI_CONTEXT_INIT_SYNC(spi_cc13xx_cc26xx_data_##n, ctx), \
|
|
SPI_CONTEXT_CS_GPIOS_INITIALIZE(DT_DRV_INST(n), ctx) \
|
|
}; \
|
|
\
|
|
SPI_CC13XX_CC26XX_DEVICE_INIT(n);
|
|
|
|
DT_INST_FOREACH_STATUS_OKAY(SPI_CC13XX_CC26XX_INIT)
|