183 lines
6.5 KiB
ReStructuredText
183 lines
6.5 KiB
ReStructuredText
.. _bluetooth-dev:
|
|
|
|
Developing Bluetooth Applications
|
|
#################################
|
|
|
|
Bluetooth applications are developed using the common infrastructure and
|
|
approach that is described in the :ref:`application` section of the
|
|
documentation.
|
|
|
|
Additional information that is only relevant to Bluetooth applications can be
|
|
found in this page.
|
|
|
|
.. _bluetooth-hw-setup:
|
|
|
|
Hardware setup
|
|
**************
|
|
|
|
This section describes the options you have when building and debugging Bluetooth
|
|
applications with Zephyr. Depending on the hardware that is available to you,
|
|
the requirements you have and the type of development you prefer you may pick
|
|
one or another setup to match your needs.
|
|
|
|
There are 4 possible hardware setups to use with Zephyr and Bluetooth:
|
|
|
|
#. Embedded
|
|
#. QEMU with an external Controller
|
|
#. Native POSIX with an external Controller
|
|
#. Simulated nRF52 with BabbleSim
|
|
|
|
Embedded
|
|
========
|
|
|
|
This setup relies on all software running directly on the embedded platform(s)
|
|
that the application is targeting.
|
|
All the :ref:`bluetooth-configs` and :ref:`bluetooth-build-types` are supported
|
|
but you might need to build Zephyr more than once if you are using a dual-chip
|
|
configuration or if you have multiple cores in your SoC each running a different
|
|
build type (e.g., one running the Host, the other the Controller).
|
|
|
|
To start developing using this setup follow the :ref:`Getting Started Guide
|
|
<getting_started>`, choose one (or more if you are using a dual-chip solution)
|
|
boards that support Bluetooth and then :ref:`run the application
|
|
<application_run_board>`).
|
|
|
|
.. _bluetooth-hci-tracing:
|
|
|
|
Embedded HCI tracing
|
|
--------------------
|
|
|
|
When running both Host and Controller in actual Integrated Circuits, you will
|
|
only see normal log messages on the console by default, without any way of
|
|
accessing the HCI traffic between the Host and the Controller. However, there
|
|
is a special Bluetooth logging mode that converts the console to use a binary
|
|
protocol that interleaves both normal log messages as well as the HCI traffic.
|
|
Set the following Kconfig options to enable this protocol before building your
|
|
application:
|
|
|
|
.. code-block:: console
|
|
|
|
CONFIG_BT_DEBUG_MONITOR=y
|
|
CONFIG_UART_CONSOLE=n
|
|
|
|
Setting :option:`CONFIG_BT_DEBUG_MONITOR` to ``y`` replaces the
|
|
:option:`CONFIG_BT_DEBUG_LOG` option, and setting :option:`CONFIG_UART_CONSOLE`
|
|
to ``n`` disables the default ``printk``/``printf`` hooks.
|
|
|
|
To decode the binary protocol that will now be sent to the console UART you need
|
|
to use the btmon tool from :ref:`BlueZ <bluetooth_bluez>`:
|
|
|
|
.. code-block:: console
|
|
|
|
$ btmon --tty <console TTY> --tty-speed 115200
|
|
|
|
Host on Linux with an external Controller
|
|
=========================================
|
|
|
|
.. note::
|
|
This is currently only available on GNU/Linux
|
|
|
|
This setup relies on a "dual-chip" :ref:`configuration <bluetooth-configs>`
|
|
which is comprised of the following devices:
|
|
|
|
#. A :ref:`Host-only <bluetooth-build-types>` application running in the
|
|
:ref:`QEMU <application_run_qemu>` emulator or the ``native_posix`` native
|
|
port of Zephyr
|
|
#. A Controller, which can be one of two types:
|
|
|
|
* A commercially available Controller
|
|
* A :ref:`Controller-only <bluetooth-build-types>` build of Zephyr
|
|
|
|
.. warning::
|
|
Certain external Controllers are either unable to accept the Host to
|
|
Controller flow control parameters that Zephyr sets by default (Qualcomm), or
|
|
do not transmit any data from the Controller to the Host (Realtek). If you
|
|
see a message similar to::
|
|
|
|
<wrn> bt_hci_core: opcode 0x0c33 status 0x12
|
|
|
|
when booting your sample of choice (make sure you have enabled
|
|
:option:`CONFIG_BT_DEBUG_LOG` in your :file:`prj.conf` before running the
|
|
sample), or if there is no data flowing from the Controller to the Host, then
|
|
you need to disable Host to Controller flow control. To do so, set
|
|
``CONFIG_BT_HCI_ACL_FLOW_CONTROL=n`` in your :file:`prj.conf`.
|
|
|
|
QEMU
|
|
----
|
|
|
|
You can run the Zephyr Host on the :ref:`QEMU emulator<application_run_qemu>`
|
|
and have it interact with a physical external Bluetooth Controller.
|
|
Refer to :ref:`bluetooth_qemu_posix` for full instructions on how to build and
|
|
run an application in this setup.
|
|
|
|
Native POSIX
|
|
------------
|
|
|
|
.. note::
|
|
This is currently only available on GNU/Linux
|
|
|
|
The :ref:`Native POSIX <native_posix>` target builds your Zephyr application
|
|
with the Zephyr kernel, and some minimal HW emulation as a native Linux
|
|
executable.
|
|
This executable is a normal Linux program, which can be debugged and
|
|
instrumented like any other, and it communicates with a physical external
|
|
Controller.
|
|
|
|
Refer to :ref:`bluetooth_qemu_posix` for full instructions on how to build and
|
|
run an application in this setup.
|
|
|
|
Simulated nRF52 with BabbleSim
|
|
==============================
|
|
|
|
.. note::
|
|
This is currently only available on GNU/Linux
|
|
|
|
The :ref:`nrf52_bsim board <nrf52_bsim>`, is a simulated target board
|
|
which emulates the necessary peripherals of a nrf52 SOC to be able to develop
|
|
and test BLE applications.
|
|
This board, uses:
|
|
|
|
* `BabbleSim`_ to simulate the nrf52 modem and the radio environment.
|
|
* The POSIX arch to emulate the processor.
|
|
* `Models of the nrf52 HW <https://github.com/BabbleSim/ext_NRF52_hw_models/>`_
|
|
|
|
Just like with the ``native_posix`` target, the build result is a normal Linux
|
|
executable.
|
|
You can find more information on how to run simulations with one or several
|
|
devices in
|
|
:ref:`this board's documentation <nrf52bsim_build_and_run>`
|
|
|
|
Currently, only :ref:`Combined builds
|
|
<bluetooth-build-types>` are possible, as this board does not yet have
|
|
any models of a UART, or USB which could be used for an HCI interface towards
|
|
another real or simulated device.
|
|
|
|
|
|
Initialization
|
|
**************
|
|
|
|
The Bluetooth subsystem is initialized using the :c:func:`bt_enable`
|
|
function. The caller should ensure that function succeeds by checking
|
|
the return code for errors. If a function pointer is passed to
|
|
:c:func:`bt_enable`, the initialization happens asynchronously, and the
|
|
completion is notified through the given function.
|
|
|
|
Bluetooth Application Example
|
|
*****************************
|
|
|
|
A simple Bluetooth beacon application is shown below. The application
|
|
initializes the Bluetooth Subsystem and enables non-connectable
|
|
advertising, effectively acting as a Bluetooth Low Energy broadcaster.
|
|
|
|
.. literalinclude:: ../../../samples/bluetooth/beacon/src/main.c
|
|
:language: c
|
|
:lines: 19-
|
|
:linenos:
|
|
|
|
The key APIs employed by the beacon sample are :c:func:`bt_enable`
|
|
that's used to initialize Bluetooth and then :c:func:`bt_le_adv_start`
|
|
that's used to start advertising a specific combination of advertising
|
|
and scan response data.
|
|
|
|
.. _BabbleSim: https://babblesim.github.io/
|