76 lines
3.0 KiB
ReStructuredText
76 lines
3.0 KiB
ReStructuredText
.. _bluetooth_direction_finding_peripheral:
|
|
|
|
Bluetooth: Direction Finding Peripheral
|
|
#######################################
|
|
|
|
Overview
|
|
********
|
|
|
|
A simple application demonstrating the BLE Direction Finding CTE transmission in
|
|
connected mode by response to a request received from connected peer device.
|
|
|
|
Requirements
|
|
************
|
|
|
|
* Nordic nRF SoC based board with Direction Finding support (example boards:
|
|
:ref:`nrf52833dk_nrf52833`, :ref:`nrf52833dk_nrf52820`, :ref:`nrf5340dk_nrf5340`)
|
|
* Antenna matrix for AoA (optional)
|
|
|
|
Check your SoC's product specification for Direction Finding support if you are
|
|
unsure.
|
|
|
|
Building and Running
|
|
********************
|
|
|
|
By default the application supports Angle of Arrival and Angle of Departure mode.
|
|
|
|
To use Angle of Arrival mode only, build this application as follows,
|
|
changing ``nrf52833dk_nrf52833`` as needed for your board:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/bluetooth/direction_finding_peripheral
|
|
:host-os: unix
|
|
:board: nrf52833dk_nrf52833
|
|
:gen-args: -DOVERLAY_CONFIG=overlay-aoa.conf
|
|
:goals: build flash
|
|
:compact:
|
|
|
|
To run the application on nRF5340DK, a Bluetooth controller application must
|
|
also run on the network core. The :ref:`bluetooth-hci-rpmsg-sample` sample
|
|
application may be used. To build this sample with direction finding support
|
|
enabled:
|
|
|
|
* Copy
|
|
:zephyr_file:`samples/bluetooth/direction_finding_peripheral/boards/nrf52833dk_nrf52833.overlay`
|
|
to a new file,
|
|
:file:`samples/bluetooth/hci_rpmsg/boards/nrf5340dk_nrf5340_cpunet.overlay`.
|
|
* Make sure the same GPIO pins are assigned to Direction Finding Extension in file
|
|
:zephyr_file:`samples/bluetooth/direction_finding_peripheral/boards/nrf5340dk_nrf5340_cpuapp.overlay`.
|
|
as those in the created file :file:`samples/bluetooth/hci_rpmsg/boards/nrf5340dk_nrf5340_cpunet.overlay`.
|
|
* Copy
|
|
:zephyr_file:`samples/bluetooth/direction_finding_peripheral/boards/nrf52833dk_nrf52833.conf`
|
|
to a new file,
|
|
:file:`samples/bluetooth/hci_rpmsg/boards/nrf5340dk_nrf5340_cpunet.conf`.
|
|
|
|
Antenna matrix configuration
|
|
****************************
|
|
|
|
To use this sample with Angle of Departure enabled on Nordic SoCs, additional
|
|
configuration must be provided via :ref:`devicetree <dt-guide>` to enable
|
|
control of the antenna array.
|
|
|
|
An example devicetree overlay is in
|
|
:zephyr_file:`samples/bluetooth/direction_finding_peripheral/boards/nrf52833dk_nrf52833.overlay`.
|
|
You can customize this overlay when building for the same board, or create your
|
|
own board-specific overlay in the same directory for a different board. See
|
|
:dtcompatible:`nordic,nrf-radio` for documentation on the properties used in
|
|
this overlay. See :ref:`set-devicetree-overlays` for information on setting up
|
|
and using overlays.
|
|
|
|
Note that antenna matrix configuration for the nRF5340 SoC is part of the
|
|
network core application. When :ref:`bluetooth-hci-rpmsg-sample` is used as the
|
|
network core application, the antenna matrix configuration should be stored in
|
|
the file
|
|
:file:`samples/bluetooth/hci_rpmsg/boards/nrf5340dk_nrf5340_cpunet.overlay`
|
|
instead.
|