73 lines
2.2 KiB
C
73 lines
2.2 KiB
C
/*
|
|
* Copyright (c) 2016 Jean-Paul Etienne <fractalclone@gmail.com>
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the "License");
|
|
* you may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*/
|
|
|
|
#ifndef __INC_BOARD_H
|
|
#define __INC_BOARD_H
|
|
|
|
#include <soc.h>
|
|
#include <gpio.h>
|
|
|
|
/* LEDS configuration */
|
|
#define LED0_GPIO_PORT "gpio0"
|
|
#define LED1_GPIO_PORT "gpio0"
|
|
#define LED2_GPIO_PORT "gpio0"
|
|
#define LED3_GPIO_PORT "gpio0"
|
|
#define LED4_GPIO_PORT "gpio0"
|
|
#define LED5_GPIO_PORT "gpio0"
|
|
#define LED6_GPIO_PORT "gpio0"
|
|
#define LED7_GPIO_PORT "gpio0"
|
|
|
|
#define LED0_GPIO_PIN 8
|
|
#define LED1_GPIO_PIN 9
|
|
#define LED2_GPIO_PIN 10
|
|
#define LED3_GPIO_PIN 11
|
|
#define LED4_GPIO_PIN 12
|
|
#define LED5_GPIO_PIN 13
|
|
#define LED6_GPIO_PIN 14
|
|
#define LED7_GPIO_PIN 15
|
|
|
|
/* Push buttons configuration */
|
|
#define SW0_GPIO_NAME "gpio0"
|
|
#define SW1_GPIO_NAME "gpio0"
|
|
#define SW2_GPIO_NAME "gpio0"
|
|
#define SW3_GPIO_NAME "gpio0"
|
|
#define SW4_GPIO_NAME "gpio0"
|
|
|
|
#define SW0_GPIO_PIN 16
|
|
#define SW1_GPIO_PIN 17
|
|
#define SW2_GPIO_PIN 18
|
|
#define SW3_GPIO_PIN 19
|
|
#define SW4_GPIO_PIN 20
|
|
|
|
/*
|
|
* GPIO PULL-UP config does not exist in pulpino
|
|
* set all to 1 for buttons to compile against apps.
|
|
*/
|
|
#define SW0_GPIO_PULL_UP 1
|
|
#define SW1_GPIO_PULL_UP 1
|
|
#define SW2_GPIO_PULL_UP 1
|
|
#define SW3_GPIO_PULL_UP 1
|
|
#define SW4_GPIO_PULL_UP 1
|
|
|
|
/* Interrupt config for push buttons */
|
|
#define SW0_GPIO_INT_CONF (GPIO_INT_EDGE | GPIO_INT_ACTIVE_HIGH)
|
|
#define SW1_GPIO_INT_CONF SW0_GPIO_INT_CONF
|
|
#define SW2_GPIO_INT_CONF SW0_GPIO_INT_CONF
|
|
#define SW3_GPIO_INT_CONF SW0_GPIO_INT_CONF
|
|
#define SW4_GPIO_INT_CONF SW0_GPIO_INT_CONF
|
|
|
|
#endif /* __INC_BOARD_H */
|