132 lines
3.3 KiB
Plaintext
132 lines
3.3 KiB
Plaintext
# BL5340-DVK board configuration
|
|
|
|
# Copyright (c) 2019-2020 Nordic Semiconductor ASA
|
|
# Copyright (c) 2021-2023 Laird Connectivity
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
if BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
config BOARD
|
|
default "bl5340_dvk_cpuapp" if BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
|
|
config I2C
|
|
default GPIO || DAC
|
|
|
|
# Code Partition:
|
|
#
|
|
# For the secure version of the board the firmware is linked at the beginning
|
|
# of the flash, or into the code-partition defined in DT if it is intended to
|
|
# be loaded by MCUboot. If the secure firmware is to be combined with a non-
|
|
# secure image (TRUSTED_EXECUTION_SECURE=y), the secure FW image shall always
|
|
# be restricted to the size of its code partition.
|
|
#
|
|
# For the non-secure version of the board, the firmware
|
|
# must be linked into the code-partition (non-secure) defined in DT, regardless.
|
|
# Apply this configuration below by setting the Kconfig symbols used by
|
|
# the linker according to the information extracted from DT partitions.
|
|
|
|
# SRAM Partition:
|
|
#
|
|
# If the secure firmware is to be combined with a non-secure image
|
|
# (TRUSTED_EXECUTION_SECURE=y), the secure FW image SRAM shall always
|
|
# be restricted to the secure image SRAM partition (sram-secure-partition).
|
|
# Otherwise (if TRUSTED_EXECUTION_SECURE is not set) the whole zephyr,sram
|
|
# may be used by the image.
|
|
#
|
|
# For the non-secure version of the board, the firmware image SRAM is
|
|
# always restricted to the allocated non-secure SRAM partition.
|
|
#
|
|
# Workaround for not being able to have commas in macro arguments
|
|
DT_CHOSEN_Z_CODE_PARTITION := zephyr,code-partition
|
|
DT_CHOSEN_Z_SRAM_PARTITION := zephyr,sram-secure-partition
|
|
|
|
if BOARD_BL5340_DVK_CPUAPP && TRUSTED_EXECUTION_SECURE
|
|
|
|
config FLASH_LOAD_SIZE
|
|
default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
config SRAM_SIZE
|
|
default $(dt_chosen_reg_size_int,$(DT_CHOSEN_Z_SRAM_PARTITION),0,K)
|
|
|
|
endif # BOARD_BL5340_DVK_CPUAPP && TRUSTED_EXECUTION_SECURE
|
|
|
|
if BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
config FLASH_LOAD_OFFSET
|
|
default $(dt_chosen_reg_addr_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
config FLASH_LOAD_SIZE
|
|
default $(dt_chosen_reg_size_hex,$(DT_CHOSEN_Z_CODE_PARTITION))
|
|
|
|
endif # BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
endif # BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
config BOARD
|
|
default "bl5340_dvk_cpunet" if BOARD_BL5340_DVK_CPUNET
|
|
|
|
config IPM_NRFX
|
|
default IPM
|
|
|
|
config MBOX_NRFX_IPC
|
|
default MBOX
|
|
|
|
if BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
choice BT_HCI_BUS_TYPE
|
|
default BT_HCI_IPC if BT
|
|
endchoice
|
|
|
|
config HEAP_MEM_POOL_ADD_SIZE_BOARD
|
|
int
|
|
default 4096 if BT_HCI_IPC
|
|
|
|
config BT_HCI_VS
|
|
default y if BT
|
|
|
|
# 2.8" TFT Touch Shield for Arduino w/Capacitive Touch Screen Module
|
|
# is mounted to the DVK using standoffs.
|
|
# https://www.buydisplay.com/2-8-inch-tft-touch-shield-for-arduino-w-capacitive-touch-screen-module
|
|
if DISPLAY
|
|
|
|
config INPUT_FT5336_INTERRUPT
|
|
default y
|
|
|
|
|
|
if LVGL
|
|
|
|
config LV_Z_VDB_SIZE
|
|
default 64
|
|
|
|
config LV_Z_BITS_PER_PIXEL
|
|
default 16
|
|
|
|
choice LV_COLOR_DEPTH
|
|
default LV_COLOR_DEPTH_16
|
|
endchoice
|
|
|
|
config LV_COLOR_16_SWAP
|
|
default y
|
|
|
|
config INPUT
|
|
default y
|
|
|
|
endif # LVGL
|
|
|
|
endif # DISPLAY
|
|
|
|
endif # BOARD_BL5340_DVK_CPUAPP || BOARD_BL5340_DVK_CPUAPP_NS
|
|
|
|
if BOARD_BL5340_DVK_CPUNET
|
|
|
|
# BT_CTLR depends on BT. When BT is enabled we should default to also
|
|
# enabling the controller.
|
|
config BT_CTLR
|
|
default y if BT
|
|
|
|
config BT_ECC
|
|
default y if BT
|
|
|
|
endif # BOARD_BL5340_DVK_CPUNET
|