235 lines
7.0 KiB
Plaintext
235 lines
7.0 KiB
Plaintext
# Kconfig - timer driver configuration options
|
|
|
|
#
|
|
# Copyright (c) 2014-2015 Wind River Systems, Inc.
|
|
# Copyright (c) 2016 Cadence Design Systems, Inc.
|
|
#
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
#
|
|
|
|
|
|
menu "Timer Drivers"
|
|
|
|
menuconfig HPET_TIMER
|
|
bool "HPET timer"
|
|
depends on (X86 || X86_64)
|
|
select IOAPIC if X86
|
|
select LOAPIC if X86
|
|
select TIMER_READS_ITS_FREQUENCY_AT_RUNTIME
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
This option selects High Precision Event Timer (HPET) as a
|
|
system timer.
|
|
|
|
if HPET_TIMER
|
|
config HPET_TIMER_BASE_ADDRESS
|
|
hex "HPET Base Address"
|
|
default 0xFED00000
|
|
help
|
|
This options specifies the base address of the HPET timer device.
|
|
|
|
config HPET_TIMER_IRQ
|
|
int "HPET Timer IRQ"
|
|
default 2
|
|
help
|
|
This option specifies the IRQ used by the HPET timer.
|
|
|
|
config HPET_TIMER_IRQ_PRIORITY
|
|
int "HPET Timer IRQ Priority"
|
|
default 4
|
|
help
|
|
This option specifies the IRQ priority used by the HPET timer.
|
|
|
|
endif #HPET_TIMER
|
|
|
|
menuconfig LOAPIC_TIMER
|
|
bool "LOAPIC timer"
|
|
depends on LOAPIC && X86
|
|
help
|
|
This option selects LOAPIC timer as a system timer.
|
|
|
|
if LOAPIC_TIMER
|
|
config LOAPIC_TIMER_IRQ
|
|
int "Local APIC Timer IRQ"
|
|
default 24
|
|
help
|
|
This option specifies the IRQ used by the LOAPIC timer.
|
|
|
|
config LOAPIC_TIMER_IRQ_PRIORITY
|
|
int "Local APIC Timer IRQ Priority"
|
|
default 2
|
|
help
|
|
This options specifies the IRQ priority used by the LOAPIC timer.
|
|
|
|
config TSC_CYCLES_PER_SEC
|
|
int "Frequency of x86 CPU timestamp counter"
|
|
default 0
|
|
help
|
|
The x86 implementation of LOAPIC k_cycle_get_32() relies on the x86 TSC.
|
|
This runs at the CPU speed and not the bus speed. If set to 0, the
|
|
value of CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC will be used instead;
|
|
many MCUs these values are the same.
|
|
|
|
endif #LOAPIC_TIMER
|
|
|
|
menuconfig ARCV2_TIMER
|
|
bool "ARC Timer"
|
|
default y
|
|
depends on ARC
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
This module implements a kernel device driver for the ARCv2 processor timer 0
|
|
and provides the standard "system clock driver" interfaces.
|
|
|
|
config ARCV2_TIMER_IRQ_PRIORITY
|
|
int "ARC timer interrupt priority"
|
|
default 0
|
|
depends on ARCV2_TIMER
|
|
help
|
|
This option specifies the IRQ priority used by the ARC timer. Lower
|
|
values have higher priority.
|
|
|
|
config CORTEX_M_SYSTICK
|
|
bool "Cortex-M SYSTICK timer"
|
|
depends on CPU_CORTEX_M_HAS_SYSTICK
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
This module implements a kernel device driver for the Cortex-M processor
|
|
SYSTICK timer and provides the standard "system clock driver" interfaces.
|
|
|
|
config ALTERA_AVALON_TIMER
|
|
bool "Altera Avalon Interval Timer"
|
|
default y
|
|
depends on NIOS2
|
|
help
|
|
This module implements a kernel device driver for the Altera Avalon
|
|
Interval Timer as described in the Embedded IP documentation, for use
|
|
with Nios II and possibly other Altera soft CPUs. It provides the
|
|
standard "system clock driver" interfaces.
|
|
|
|
config NRF_RTC_TIMER
|
|
bool "nRF Real Time Counter (NRF_RTC1) Timer"
|
|
depends on CLOCK_CONTROL
|
|
depends on SOC_COMPATIBLE_NRF
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
This module implements a kernel device driver for the nRF Real Time
|
|
Counter NRF_RTC1 and provides the standard "system clock driver"
|
|
interfaces.
|
|
|
|
config RISCV_MACHINE_TIMER
|
|
bool "RISCV Machine Timer"
|
|
depends on SOC_FAMILY_RISCV_PRIVILEGE
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
This module implements a kernel device driver for the generic RISCV machine
|
|
timer driver. It provides the standard "system clock driver" interfaces.
|
|
|
|
config RV32M1_LPTMR_TIMER
|
|
bool "RV32M1 LPTMR system timer driver"
|
|
default y
|
|
depends on SOC_OPENISA_RV32M1_RISCV32
|
|
depends on !TICKLESS_IDLE
|
|
depends on RV32M1_INTMUX
|
|
help
|
|
This module implements a kernel device driver for using the LPTMR
|
|
peripheral as the system clock. It provides the standard "system clock
|
|
driver" interfaces.
|
|
|
|
config LITEX_TIMER
|
|
bool "LiteX Timer"
|
|
default y
|
|
depends on !TICKLESS_IDLE
|
|
depends on SOC_RISCV32_LITEX_VEXRISCV
|
|
help
|
|
This module implements a kernel device driver for LiteX Timer.
|
|
|
|
config NATIVE_POSIX_TIMER
|
|
bool "(POSIX) native_posix timer driver"
|
|
default y
|
|
depends on BOARD_NATIVE_POSIX
|
|
help
|
|
This module implements a kernel device driver for the native_posix HW timer
|
|
model
|
|
|
|
config XTENSA_TIMER
|
|
bool "Xtensa timer support"
|
|
depends on XTENSA
|
|
default y
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
Enables a system timer driver for Xtensa based on the CCOUNT
|
|
and CCOMPARE special registers.
|
|
|
|
config XTENSA_TIMER_ID
|
|
int "System timer CCOMPAREn register index"
|
|
default 1
|
|
depends on XTENSA_TIMER
|
|
help
|
|
Index of the CCOMPARE register (and associated interrupt)
|
|
used for the system timer. Xtensa CPUs have hard-configured
|
|
interrupt priorities associated with each timer, and some of
|
|
them can be unmaskable (and thus not usable by OS code that
|
|
need synchronization, like the timer subsystem!). Choose
|
|
carefully. Generally you want the timer with the highest
|
|
priority maskable interrupt.
|
|
|
|
config SAM0_RTC_TIMER
|
|
bool "Atmel SAM0 series RTC timer"
|
|
depends on SOC_FAMILY_SAM0
|
|
select TICKLESS_CAPABLE
|
|
help
|
|
This module implements a kernel device driver for the Atmel SAM0
|
|
series Real Time Counter and provides the standard "system clock
|
|
driver" interfaces.
|
|
|
|
config SYSTEM_CLOCK_DISABLE
|
|
bool "API to disable system clock"
|
|
help
|
|
This option enables the sys_clock_disable() API in the kernel. It is
|
|
needed by some subsystems (which will automatically select it), but is
|
|
rarely needed by applications.
|
|
|
|
config TIMER_READS_ITS_FREQUENCY_AT_RUNTIME
|
|
bool "Timer queries its hardware to find its frequency at runtime"
|
|
help
|
|
The drivers select this option automatically when needed. Do not modify
|
|
this unless you have a very good reason for it.
|
|
|
|
config SYSTEM_CLOCK_INIT_PRIORITY
|
|
int "System clock driver initialization priority"
|
|
default 0
|
|
help
|
|
This options can be used to set a specific initialization priority
|
|
value for the system clock driver. As driver initialization might need
|
|
the clock to be running already, you should let the default value as it
|
|
is (0).
|
|
|
|
config TICKLESS_CAPABLE
|
|
bool "Timer driver supports tickless operation"
|
|
help
|
|
Timer drivers should select this flag if they are capable of
|
|
supporting tickless operation. That is, a call to
|
|
z_clock_set_timeout() with a number of ticks greater than
|
|
one should be expected not to produce a call to
|
|
z_clock_announce() (really, not to produce an interrupt at
|
|
all) until the specified expiration.
|
|
|
|
config QEMU_TICKLESS_WORKAROUND
|
|
bool "Disable tickless on qemu due to asynchrony bug"
|
|
depends on QEMU_TARGET && TICKLESS_KERNEL
|
|
help
|
|
Qemu (without -icount) has trouble keeping time when the
|
|
host process needs to timeshare. The host OS will routinely
|
|
schedule out a process at timescales equivalent to the guest
|
|
tick rate. With traditional ticks delivered regularly by
|
|
the hardware, that's mostly OK as it looks like a late
|
|
interrupt. But in tickless mode, the driver needs some CPU
|
|
in order to schedule the tick in the first place. If that
|
|
gets delayed across a tick boundary, time gets wonky. This
|
|
tunable is a hint to the driver to disable tickless
|
|
accounting on qemu. Use it only on tests that are known to
|
|
have problems.
|
|
|
|
endmenu
|