99 lines
2.1 KiB
Plaintext
99 lines
2.1 KiB
Plaintext
# Kconfig - USB device configuration options
|
|
|
|
#
|
|
# Copyright (c) 2016 Wind River Systems, Inc.
|
|
#
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
#
|
|
|
|
if USB
|
|
|
|
config USB_DEVICE_DRIVER
|
|
bool
|
|
|
|
config USB_DW
|
|
bool
|
|
prompt "Designware USB Device Controller Driver"
|
|
select USB_DEVICE_DRIVER
|
|
help
|
|
Designware USB Device Controller Driver.
|
|
|
|
config USB_DW_IRQ_PRI
|
|
int "DesignWare USB Driver Interrupt priority"
|
|
depends on USB_DW
|
|
help
|
|
USB interrupt priority.
|
|
|
|
config USB_DW_USB_2_0
|
|
bool
|
|
prompt "DesignWare Controller and PHY support for USB specification 2.0"
|
|
depends on USB_DW
|
|
help
|
|
Indicates whether or not USB specification version 2.0 is supported
|
|
|
|
config USB_DC_STM32
|
|
bool
|
|
prompt "USB device controller driver for STM32 devices"
|
|
depends on SOC_FAMILY_STM32
|
|
select USB_DEVICE_DRIVER
|
|
select USE_STM32_LL_USB if !SOC_SERIES_STM32F0X && !SOC_SERIES_STM32F3X && !SOC_SERIES_STM32L0X
|
|
select USE_STM32_HAL_PCD
|
|
select USE_STM32_HAL_PCD_EX
|
|
select HAS_DTS_USB
|
|
help
|
|
Enable USB support on the STM32 F0, F1, F3, F4, F7, L0 and L4 family of
|
|
processors.
|
|
|
|
config USB_DC_SAM0
|
|
bool
|
|
prompt "SAM0 series USB Device Controller driver"
|
|
depends on SOC_FAMILY_SAM0
|
|
select USB_DEVICE_DRIVER
|
|
help
|
|
SAM0 family USB device controller Driver.
|
|
|
|
config USB_NRF52840
|
|
bool
|
|
prompt "Nordic Semiconductor nRF52840 USB Device Controller Driver"
|
|
depends on SOC_NRF52840
|
|
select USB_DEVICE_DRIVER
|
|
select HAS_DTS_USB
|
|
help
|
|
nRF52840 USB Device Controller Driver
|
|
|
|
config USB_KINETIS
|
|
bool
|
|
prompt "Kinetis USB Device Controller Driver"
|
|
select USB_DEVICE_DRIVER
|
|
help
|
|
Kinetis USB Device Controller Driver.
|
|
|
|
config SYS_LOG_USB_DRIVER_LEVEL
|
|
int
|
|
prompt "USB driver log level"
|
|
depends on SYS_LOG
|
|
default 0
|
|
help
|
|
Sets log level for USB driver
|
|
|
|
Levels are:
|
|
|
|
- 0 OFF, do not write
|
|
|
|
- 1 ERROR, only write SYS_LOG_ERR
|
|
|
|
- 2 WARNING, write SYS_LOG_WRN in addition to previous level
|
|
|
|
- 3 INFO, write SYS_LOG_INF in addition to previous levels
|
|
|
|
- 4 DEBUG, write SYS_LOG_DBG in addition to previous levels
|
|
|
|
config USB_DC_STM32_DISCONN_ENABLE
|
|
bool
|
|
depends on USB_DC_STM32
|
|
help
|
|
Say Y if your board uses USB DISCONNECT pin to enable the
|
|
pull-up resistor on USB DP.
|
|
|
|
endif # USB
|