268 lines
9.5 KiB
ReStructuredText
268 lines
9.5 KiB
ReStructuredText
.. _tlsr9518adk80d:
|
||
|
||
Telink TLSR9518ADK80D
|
||
#####################
|
||
|
||
Overview
|
||
********
|
||
|
||
The TLSR9518A Generic Starter Kit is a hardware platform which
|
||
can be used to verify the `Telink TLSR951x series chipset`_ and develop applications
|
||
for several 2.4 GHz air interface standards including Bluetooth 5.2 (Basic data
|
||
rate, Enhanced data rate, LE, Indoor positioning and BLE Mesh),
|
||
Zigbee 3.0, Homekit, 6LoWPAN, Thread and 2.4 Ghz proprietary.
|
||
|
||
.. figure:: img/tlsr9518adk80d.jpg
|
||
:align: center
|
||
:alt: TLSR9518ADK80D
|
||
|
||
More information about the board can be found at the `Telink B91 Generic Starter Kit Hardware Guide`_ website.
|
||
|
||
Hardware
|
||
********
|
||
|
||
The TLSR9518A SoC integrates a powerful 32-bit RISC-V MCU, DSP, AI Engine, 2.4 GHz ISM Radio, 256
|
||
KB SRAM (128 KB of Data Local Memory and 128 KB of Instruction Local Memory), external Flash memory,
|
||
stereo audio codec, 14 bit AUX ADC, analog and digital Microphone input, PWM, flexible IO interfaces,
|
||
and other peripheral blocks required for advanced IoT, hearable, and wearable devices.
|
||
|
||
.. figure:: img/tlsr9518_block_diagram.jpg
|
||
:align: center
|
||
:alt: TLSR9518ADK80D_SOC
|
||
|
||
The TLSR9518ADK80D default board configuration provides the following hardware components:
|
||
|
||
- RF conducted antenna
|
||
- 1 MB External Flash memory with reset button
|
||
- Chip reset button
|
||
- Mini USB interface
|
||
- 4-wire JTAG
|
||
- 4 LEDs, Key matrix up to 4 keys
|
||
- 2 line-in function (Dual Analog microphone supported when switching jumper from microphone path)
|
||
- Dual Digital microphone
|
||
- Stereo line-out
|
||
|
||
Supported Features
|
||
==================
|
||
|
||
The Zephyr TLSR9518ADK80D board configuration supports the following hardware features:
|
||
|
||
+----------------+------------+------------------------------+
|
||
| Interface | Controller | Driver/Component |
|
||
+================+============+==============================+
|
||
| PLIC | on-chip | interrupt_controller |
|
||
+----------------+------------+------------------------------+
|
||
| RISC-V Machine | on-chip | timer |
|
||
| Timer (32 KHz) | | |
|
||
+----------------+------------+------------------------------+
|
||
| PINCTRL | on-chip | pinctrl |
|
||
+----------------+------------+------------------------------+
|
||
| GPIO | on-chip | gpio |
|
||
+----------------+------------+------------------------------+
|
||
| UART | on-chip | serial |
|
||
+----------------+------------+------------------------------+
|
||
| PWM | on-chip | pwm |
|
||
+----------------+------------+------------------------------+
|
||
| TRNG | on-chip | entropy |
|
||
+----------------+------------+------------------------------+
|
||
| FLASH (MSPI) | on-chip | flash |
|
||
+----------------+------------+------------------------------+
|
||
| RADIO | on-chip | Bluetooth, |
|
||
| | | ieee802154, OpenThread |
|
||
+----------------+------------+------------------------------+
|
||
| SPI (Master) | on-chip | spi |
|
||
+----------------+------------+------------------------------+
|
||
| I2C (Master) | on-chip | i2c |
|
||
+----------------+------------+------------------------------+
|
||
| ADC | on-chip | adc |
|
||
+----------------+------------+------------------------------+
|
||
|
||
.. note::
|
||
To support "button" example project PC3-KEY3 (J20-19, J20-20) jumper needs to be removed and KEY3 (J20-19) should be connected to VDD3_DCDC (J51-13) externally.
|
||
|
||
For the rest example projects use the default jumpers configuration.
|
||
|
||
Other hardware features and example projects are not supported yet.
|
||
|
||
Limitations
|
||
-----------
|
||
|
||
- Maximum 3 GPIO pins could be configured to generate interrupts simultaneously. All pins must be related to different ports and use different IRQ numbers.
|
||
- DMA mode is not supported by I2C, SPI and Serial Port.
|
||
- UART hardware flow control is not implemented.
|
||
- SPI Slave mode is not implemented.
|
||
- I2C Slave mode is not implemented.
|
||
|
||
Default configuration and IOs
|
||
=============================
|
||
|
||
System Clock
|
||
------------
|
||
|
||
The TLSR9518ADK80D board is configured to use the 24 MHz external crystal oscillator
|
||
with the on-chip PLL/DIV generating the 48 MHz system clock.
|
||
The following values also could be assigned to the system clock in the board DTS file
|
||
:zephyr_file:`boards/telink/tlsr9518adk80d/tlsr9518adk80d.dts`:
|
||
|
||
- 16000000
|
||
- 24000000
|
||
- 32000000
|
||
- 48000000
|
||
- 64000000
|
||
- 96000000
|
||
|
||
.. code-block::
|
||
|
||
&cpu0 {
|
||
clock-frequency = <48000000>;
|
||
};
|
||
|
||
PINs Configuration
|
||
------------------
|
||
|
||
The TLSR9518A SoC has five GPIO controllers (PORT_A to PORT_E), but only two are
|
||
currently enabled (PORT_B for LEDs control and PORT_C for buttons) in the board DTS file:
|
||
|
||
- LED0 (blue): PB4, LED1 (green): PB5, LED2 (white): PB6, LED3 (red): PB7
|
||
- Key Matrix SW0: PC2_PC3, SW1: PC2_PC1, SW2: PC0_PC3, SW3: PC0_PC1
|
||
|
||
Peripheral's pins on the SoC are mapped to the following GPIO pins in the
|
||
:zephyr_file:`boards/telink/tlsr9518adk80d/tlsr9518adk80d.dts` file:
|
||
|
||
- UART0 TX: PB2, RX: PB3
|
||
- UART1 TX: PC6, RX: PC7
|
||
- PWM Channel 0: PB4
|
||
- PSPI CS0: PC4, CLK: PC5, MISO: PC6, MOSI: PC7
|
||
- HSPI CS0: PA1, CLK: PA2, MISO: PA3, MOSI: PA4
|
||
- I2C SCL: PE1, SDA: PE3
|
||
|
||
Serial Port
|
||
-----------
|
||
|
||
The TLSR9518A SoC has 2 UARTs. The Zephyr console output is assigned to UART0.
|
||
The default settings are 115200 8N1.
|
||
|
||
Programming and debugging
|
||
*************************
|
||
|
||
Building
|
||
========
|
||
|
||
.. important::
|
||
|
||
These instructions assume you've set up a development environment as
|
||
described in the :ref:`getting_started`.
|
||
|
||
To build applications using the default RISC-V toolchain from Zephyr SDK, just run the west build command.
|
||
Here is an example for the "hello_world" application.
|
||
|
||
.. code-block:: console
|
||
|
||
# From the root of the zephyr repository
|
||
west build -b tlsr9518adk80d samples/hello_world
|
||
|
||
To use `Telink RISC-V Linux Toolchain`_, ``ZEPHYR_TOOLCHAIN_VARIANT`` and ``CROSS_COMPILE`` variables need to be set.
|
||
In addition ``CONFIG_FPU=y`` must be selected in :zephyr_file:`boards/telink/tlsr9518adk80d/tlsr9518adk80d_defconfig` file since this
|
||
toolchain is compatible only with the float point unit usage.
|
||
|
||
.. code-block:: console
|
||
|
||
# Set Zephyr toolchain variant to cross-compile
|
||
export ZEPHYR_TOOLCHAIN_VARIANT=cross-compile
|
||
# Specify the Telink RISC-V Toolchain location
|
||
export CROSS_COMPILE=~/toolchains/nds32le-elf-mculib-v5f/bin/riscv32-elf-
|
||
# From the root of the zephyr repository
|
||
west build -b tlsr9518adk80d samples/hello_world
|
||
|
||
`Telink RISC-V Linux Toolchain`_ is available on the `Burning and Debugging Tools for TLSR9 Series in Linux`_ page.
|
||
|
||
Open a serial terminal with the following settings:
|
||
|
||
- Speed: 115200
|
||
- Data: 8 bits
|
||
- Parity: None
|
||
- Stop bits: 1
|
||
|
||
Flash the board, reset and observe the following messages on the selected
|
||
serial port:
|
||
|
||
.. code-block:: console
|
||
|
||
*** Booting Zephyr OS version 2.5.0 ***
|
||
Hello World! tlsr9518adk80d
|
||
|
||
|
||
Flashing
|
||
========
|
||
|
||
To flash the TLSR9518ADK80D board see the sources below:
|
||
|
||
- `Burning and Debugging Tools for all Series`_
|
||
- `Burning and Debugging Tools for TLSR9 Series`_
|
||
- `Burning and Debugging Tools for TLSR9 Series in Linux`_
|
||
|
||
It is also possible to use the west flash command, but additional steps are required to set it up:
|
||
|
||
- Download `Telink RISC-V Linux Toolchain`_. The toolchain contains tools for the board flashing as well.
|
||
- Since the ICEman tool is created for the 32-bit OS version it is necessary to install additional packages in case of the 64-bit OS version.
|
||
|
||
.. code-block:: console
|
||
|
||
sudo dpkg --add-architecture i386
|
||
sudo apt-get update
|
||
sudo apt-get install -y libc6:i386 libncurses5:i386 libstdc++6:i386
|
||
|
||
- Run the "ICEman.sh" script.
|
||
|
||
.. code-block:: console
|
||
|
||
# From the root of the {path to the Telink RISC-V Linux Toolchain}/ice repository
|
||
sudo ./ICEman.sh
|
||
|
||
- Now you should be able to run the west flash command with the toolchain path specified (TELINK_TOOLCHAIN_PATH).
|
||
|
||
.. code-block:: console
|
||
|
||
west flash --telink-tools-path=$TELINK_TOOLCHAIN_PATH
|
||
|
||
- You can also run the west flash command without toolchain path specification if add SPI_burn and ICEman to PATH.
|
||
|
||
.. code-block:: console
|
||
|
||
export PATH=$TELINK_TOOLCHAIN_PATH/flash/bin:"$PATH"
|
||
export PATH=$TELINK_TOOLCHAIN_PATH/ice:"$PATH"
|
||
|
||
Debugging
|
||
=========
|
||
|
||
This port supports UART debug and OpenOCD+GDB. The `west debug` command also supported. You may run
|
||
it in a simple way, like:
|
||
|
||
.. code-block:: console
|
||
|
||
west debug
|
||
|
||
Or with additional arguments, like:
|
||
|
||
.. code-block:: console
|
||
|
||
west debug --gdb-port=<port_number> --gdb-ex=<additional_ex_arguments>
|
||
|
||
Example:
|
||
|
||
.. code-block:: console
|
||
|
||
west debug --gdb-port=1111 --gdb-ex="-ex monitor reset halt -ex b main -ex continue"
|
||
|
||
References
|
||
**********
|
||
|
||
.. target-notes::
|
||
|
||
.. _Telink TLSR951x series chipset: https://wiki.telink-semi.cn/wiki/chip-series/TLSR951x-Series/
|
||
.. _Telink B91 Generic Starter Kit Hardware Guide: https://wiki.telink-semi.cn/wiki/Hardware/B91_Generic_Starter_Kit_Hardware_Guide/
|
||
.. _Telink RISC-V Linux Toolchain: https://wiki.telink-semi.cn/tools_and_sdk/Tools/IDE/telink_riscv_linux_toolchain.zip
|
||
.. _Burning and Debugging Tools for all Series: https://wiki.telink-semi.cn/wiki/IDE-and-Tools/Burning-and-Debugging-Tools-for-all-Series/
|
||
.. _Burning and Debugging Tools for TLSR9 Series: https://wiki.telink-semi.cn/wiki/IDE-and-Tools/Burning-and-Debugging-Tools-for-TLSR9-Series/
|
||
.. _Burning and Debugging Tools for TLSR9 Series in Linux: https://wiki.telink-semi.cn/wiki/IDE-and-Tools/BDT_for_TLSR9_Series_in_Linux/
|