OrgZephyr/zephyr
OrgZephyr
/
zephyr
mirror of https://github.com/zephyrproject-rtos/zephyr.git
1
0
Fork 0
Code Issues Releases Wiki Activity
zephyr/boards/nxp/mimxrt1024_evk/doc/index.rst

296 lines
11 KiB
ReStructuredText
Raw Blame History

.. _mimxrt1024_evk:
NXP MIMXRT1024-EVK
##################
Overview
********
The i.MX RT1024 expands the i.MX RT crossover processor families by providing
high-performance feature set in low-cost LQFP packages, further simplifying
board design and layout for customers. The i.MX RT1024 runs on the Arm®
Cortex®-M7 core at 500 MHz.
.. image:: mimxrt1024_evk.jpg
:align: center
:alt: MIMXRT1024-EVK
Hardware
********
- MIMXRT1024DAG5A MCU (600 MHz, 256 KB on-chip memory, 4096KB on-chip QSPI
flash)
- Memory
- 256 Mbit SDRAM
- 32 Mbit QSPI Flash
- TF socket for SD card
- Connectivity
- 10/100 Mbit/s Ethernet PHY
- Micro USB host and OTG connectors
- CAN transceivers
- Arduino interface
- Audio
- Audio Codec
- 4-pole audio headphone jack
- Microphone
- External speaker connection
- Power
- 5 V DC jack
- Debug
- JTAG 10-pin connector
- OpenSDA with DAPLink
- Sensor
- 6-axis FXOS8700CQ digital accelerometer and magnetometer
For more information about the MIMXRT1024 SoC and MIMXRT1024-EVK board, see
these references:
- `i.MX RT1024 Website`_
- `i.MX RT1024 Datasheet`_
- `i.MX RT1024 Reference Manual`_
- `MIMXRT1024-EVK Website`_
- `MIMXRT1024-EVK User Guide`_
- `MIMXRT1024-EVK Design Files`_
External Memory
===============
This platform has the following external memories:
+----------------+------------+-------------------------------------+
| Device | Controller | Status |
+================+============+=====================================+
| MT48LC16M16A2P | SEMC | Enabled via device configuration |
| | | data block, which sets up SEMC at |
| | | boot time |
+----------------+------------+-------------------------------------+
Supported Features
==================
The mimxrt1024_evk board configuration supports the hardware features listed
below. For additional features not yet supported, please also refer to the
:ref:`mimxrt1064_evk` , which is the superset board in NXP's i.MX RT10xx family.
NXP prioritizes enabling the superset board with NXP's Full Platform Support for
Zephyr. Therefore, the mimxrt1064_evk board may have additional features
already supported, which can also be re-used on this mimxrt1024_evk board:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| SYSTICK | on-chip | systick |
+-----------+------------+-------------------------------------+
| FLASH | on-chip | QSPI flash |
+-----------+------------+-------------------------------------+
| GPIO | on-chip | gpio |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
| SPI | on-chip | spi |
+-----------+------------+-------------------------------------+
| ENET | on-chip | ethernet |
+-----------+------------+-------------------------------------+
| CAN | on-chip | can |
+-----------+------------+-------------------------------------+
| WATCHDOG | on-chip | watchdog |
+-----------+------------+-------------------------------------+
| HWINFO | on-chip | reset cause |
+-----------+------------+-------------------------------------+
| DMA | on-chip | dma |
+-----------+------------+-------------------------------------+
| ADC | on-chip | adc |
+-----------+------------+-------------------------------------+
| GPT | on-chip | gpt |
+-----------+------------+-------------------------------------+
| USB | on-chip | USB |
+-----------+------------+-------------------------------------+
| TRNG | on-chip | entropy |
+-----------+------------+-------------------------------------+
| FLEXSPI | on-chip | flash programming |
+-----------+------------+-------------------------------------+
The default configuration can be found in
:zephyr_file:`boards/nxp/mimxrt1024_evk/mimxrt1024_evk_defconfig`
Other hardware features are not currently supported by the port.
Connections and I/Os
====================
The MIMXRT1024 SoC has five pairs of pinmux/gpio controllers.
+---------------+-----------------+---------------------------+
| Name | Function | Usage |
+===============+=================+===========================+
| GPIO_AD_B1_08 | GPIO | LED |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_06 | LPUART1_TX | UART Console |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_07 | LPUART1_RX | UART Console |
+---------------+-----------------+---------------------------+
| WAKEUP | GPIO | SW4 |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_04 | ENET_RST | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_08 | ENET_REF_CLK | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_09 | ENET_RX_DATA01 | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_10 | ENET_RX_DATA00/LPSPI1_SCK | Ethernet/SPI |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_11 | ENET_RX_EN/LPSPI1_PCS0 | Ethernet/SPI |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_12 | ENET_RX_ER/LPSPI1_SDO | Ethernet/SPI |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_13 | ENET_TX_EN/LPSPI1_SDI | Ethernet/SPI |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_14 | ENET_TX_DATA00 | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_AD_B0_15 | ENET_TX_DATA01 | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_AD_B1_06 | ENET_INT | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_EMC_41 | ENET_MDC | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_EMC_40 | ENET_MDIO | Ethernet |
+---------------+-----------------+---------------------------+
| GPIO_SD_B1_00 | FLEXCAN1_TX | CAN TX |
+---------------+-----------------+---------------------------+
| GPIO_SD_B1_01 | FLEXCAN1_RX | CAN RX |
+---------------+-----------------+---------------------------+
| GPIO_SD_B1_02 | LPI2C4_SCL | I2C SCL |
+---------------+-----------------+---------------------------+
| GPIO_SD_B1_03 | LPI2C4_SDA | I2C SDA |
+---------------+-----------------+---------------------------+
| GPIO_SD_B1_05 | DQS | QSPI flash |
+---------------+-----------------+---------------------------+
| GPIO_AD_B1_11 | ADC1 | ADC1 Channel 11 |
+---------------+-----------------+---------------------------+
| GPIO_AD_B1_10 | ADC1 | ADC1 Channel 10 |
+---------------+-----------------+---------------------------+
| GPIO_AD_B1_10 | FLEXPWM1 | FLEXPWM1 Channel A2 |
+---------------+-----------------+---------------------------+
System Clock
============
The MIMXRT1024 SoC is configured to use SysTick as the system clock source,
running at 500MHz.
When power management is enabled, the 32 KHz low frequency
oscillator on the board will be used as a source for the GPT timer to
generate a system clock. This clock enables lower power states, at the
cost of reduced resolution
Serial Port
===========
The MIMXRT1024 SoC has eight UARTs. One is configured for the console and the
remaining are not used.
Programming and Debugging
*************************
This board supports 2 debug host tools. Please install your preferred host
tool, then follow the instructions in `Configuring a Debug Probe`_ to
configure the board appropriately.
* :ref:`jlink-debug-host-tools` (Default, Supported by NXP)
* :ref:`pyocd-debug-host-tools` (Not supported by NXP)
Configuring a Debug Probe
=========================
For the RT1024, J47/J48 are the SWD isolation jumpers, J42 is the DFU
mode jumper, and J55 is the 10 pin JTAG/SWD header.
.. include:: ../../common/rt1xxx-lpclink2-debug.rst
:start-after: rt1xxx-lpclink2-probes
Configuring a Console
=====================
Regardless of your choice in debug probe, we will use the OpenSDA
microcontroller as a usb-to-serial adapter for the serial console. Check that
jumpers J50 and J46 are **on** (they are on by default when boards ship from
the factory) to connect UART signals to the OpenSDA microcontroller.
Connect a USB cable from your PC to J23.
Use the following settings with your serial terminal of choice (minicom, putty,
etc.):
- Speed: 115200
- Data: 8 bits
- Parity: None
- Stop bits: 1
Flashing
========
Here is an example for the :ref:`hello_world` application.
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: mimxrt1024_evk
:goals: flash
Open a serial terminal, reset the board (press the SW9 button), and you should
see the following message in the terminal:
.. code-block:: console
***** Booting Zephyr OS v2.4.0-rc1 *****
Hello World! mimxrt1024_evk
Debugging
=========
Here is an example for the :ref:`hello_world` application.
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: mimxrt1024_evk
:goals: debug
Open a serial terminal, step through the application in your debugger, and you
should see the following message in the terminal:
.. code-block:: console
***** Booting Zephyr OS v2.4.0-rc1 *****
Hello World! mimxrt1024_evk
.. _MIMXRT1024-EVK Website:
https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt1024-evaluation-kit:MIMXRT1024-EVK
.. _MIMXRT1024-EVK User Guide:
https://www.nxp.com/webapp/Download?colCode=MIMXRT1024EVKHUG
.. _MIMXRT1024-EVK Design Files:
https://www.nxp.com/webapp/Download?colCode=MIMXRT1024-EVK-Design-Files
.. _i.MX RT1024 Website:
https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/i-mx-rt-crossover-mcus/i-mx-rt1024-crossover-processor-with-arm-cortex-m7-core:i.MX-RT1024
.. _i.MX RT1024 Datasheet:
https://www.nxp.com.cn/docs/en/data-sheet/IMXRT1024CEC.pdf
.. _i.MX RT1024 Reference Manual:
https://www.nxp.com/webapp/Download?colCode=IMXRT1024RM
Reference in New Issue View Git Blame Copy Permalink