239 lines
7.6 KiB
ReStructuredText
239 lines
7.6 KiB
ReStructuredText
.. _nucleo_l4r5zi_board:
|
|
|
|
ST Nucleo L4R5ZI
|
|
################
|
|
|
|
Overview
|
|
********
|
|
|
|
The Nucleo L4R5ZI board features an ARM Cortex-M4 based STM32L4R5ZI MCU
|
|
with a wide range of connectivity support and configurations. Here are
|
|
some highlights of the Nucleo L4R5ZI board:
|
|
|
|
|
|
- STM32 microcontroller in LQFP144 package
|
|
- Two types of extension resources:
|
|
|
|
- Arduino Uno V3 connectivity
|
|
- ST morpho extension pin headers for full access to all STM32 I/Os
|
|
|
|
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
|
|
- Flexible board power supply:
|
|
|
|
- USB VBUS or external source(3.3V, 5V, 7 - 12V)
|
|
- Power management access point
|
|
|
|
- Three User LEDs: LD1 (Green), LD2 (Blue), LD3 (Red)
|
|
- Two push-buttons: USER and RESET
|
|
|
|
.. image:: img/nucleo144_ulp_logo_1024.jpg
|
|
:width: 250px
|
|
:align: center
|
|
:height: 250px
|
|
:alt: Nucleo L4R5ZI
|
|
|
|
More information about the board can be found at the `Nucleo L4R5ZI website`_.
|
|
|
|
Hardware
|
|
********
|
|
|
|
The STM32L4R5ZI SoC provides the following hardware IPs:
|
|
|
|
- Ultra-low-power with FlexPowerControl (down to 130 nA Standby mode
|
|
and 100 uA/MHz run mode)
|
|
- Core: ARM |reg| 32-bit Cortex |reg|-M4 CPU with FPU, adaptive
|
|
real-time accelerator (ART Accelerator) allowing 0-wait-state
|
|
execution from Flash memory, frequency up to 120 MHz, MPU, 150
|
|
DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions
|
|
- Clock Sources:
|
|
|
|
- 4 to 48 MHz crystal oscillator
|
|
- 32 kHz crystal oscillator for RTC (LSE)
|
|
- Internal 16 MHz factory-trimmed RC ( |plusminus| 1%)
|
|
- Internal low-power 32 kHz RC ( |plusminus| 5%)
|
|
- Internal multispeed 100 kHz to 48 MHz oscillator, auto-trimmed by
|
|
LSE (better than |plusminus| 0.25 % accuracy)
|
|
- Internal 48 MHz with clock recovery
|
|
- 3 PLLs for system clock, USB, audio, ADC
|
|
|
|
- RTC with HW calendar, alarms and calibration
|
|
- Up to 24 capacitive sensing channels: support touchkey, linear and
|
|
rotary touch sensors
|
|
- Advanced graphics features
|
|
|
|
- Chrom-ART Accelerator™ (DMA2D) for enhanced graphic content creation
|
|
- Chrom-GRC™ (GFXMMU) allowing up to 20% of graphic resources optimization
|
|
- MIPI® DSI Host controller with two DSI lanes running at up to 500
|
|
Mbits/s each
|
|
- LCD-TFT controller
|
|
|
|
- 16x timers
|
|
|
|
- 2 x 16-bit advanced motor-control
|
|
- 2 x 32-bit and 5 x 16-bit general purpose
|
|
- 2x 16-bit basic
|
|
- 2x low-power 16-bit timers (available in Stop mode)
|
|
- 2x watchdogs
|
|
- SysTick timer
|
|
|
|
- Up to 136 fast I/Os, most 5 V-tolerant, up to 14 I/Os with
|
|
independent supply down to 1.08 V
|
|
- Memories
|
|
|
|
- 2-Mbyte Flash, 2 banks read-while-write, proprietary code readout protection
|
|
- 640 Kbytes of SRAM including 64 Kbytes with hardware parity check
|
|
- External memory interface for static memories supporting SRAM,
|
|
PSRAM, NOR, NAND and FRAM memories
|
|
- 2 x OctoSPI memory interface
|
|
|
|
- 4x digital filters for sigma delta modulator
|
|
- Rich analog peripherals (independent supply)
|
|
|
|
- 12-bit ADC 5 Msps, up to 16-bit with hardware oversampling, 200 μA/Msps
|
|
- 2x 12-bit DAC, low-power sample and hold
|
|
- 2x operational amplifiers with built-in PGA
|
|
- 2x ultra-low-power comparators
|
|
|
|
- 20x communication interfaces
|
|
|
|
- USB OTG 2.0 full-speed, LPM and BCD
|
|
- 2x SAIs (serial audio interface)
|
|
- 4x I2C FM+(1 Mbit/s), SMBus/PMBus
|
|
- 6x USARTs (ISO 7816, LIN, IrDA, modem)
|
|
- 3x SPIs (5x SPIs with the dual OctoSPI)
|
|
- CAN (2.0B Active) and SDMMC
|
|
|
|
- 14-channel DMA controller
|
|
- True random number generator
|
|
- CRC calculation unit, 96-bit unique ID
|
|
- 8- to 14-bit camera interface up to 32 MHz (black and white) or 10 MHz (color)
|
|
- Development support: serial wire debug (SWD), JTAG, Embedded Trace
|
|
Macrocell (ETM)
|
|
|
|
More information about STM32L4R5ZI can be found here:
|
|
|
|
- `STM32L4R5ZI on www.st.com`_
|
|
- `STM32L4R5 reference manual`_
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The Zephyr nucleo_l4r5zi board configuration supports the following
|
|
hardware features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| I2C | on-chip | i2c |
|
|
+-----------+------------+-------------------------------------+
|
|
| PWM | on-chip | pwm |
|
|
+-----------+------------+-------------------------------------+
|
|
| SPI | on-chip | spi |
|
|
+-----------+------------+-------------------------------------+
|
|
| USB | on-chip | usb |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
Other hardware features are not yet supported on this Zephyr port.
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
``boards/arm/nucleo_l4r5zi/nucleo_l4r5zi_defconfig``
|
|
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
Nucleo L4R5ZI Board has 8 GPIO controllers. These controllers are
|
|
responsible for pin muxing, input/output, pull-up, etc.
|
|
|
|
Available pins:
|
|
---------------
|
|
.. image:: img/nucleo144_layout.jpg
|
|
:width: 720px
|
|
:align: center
|
|
:height: 540px
|
|
:alt: Nucleo L4R5ZI Arduino connectors
|
|
|
|
For mode details please refer to `STM32 Nucleo-144 board User Manual`_.
|
|
|
|
Default Zephyr Peripheral Mapping:
|
|
----------------------------------
|
|
|
|
- UART_1_TX : PA9
|
|
- UART_1_RX : PA10
|
|
- UART_2_TX : PA2
|
|
- UART_2_RX : PA3
|
|
- UART_3_TX : PB10
|
|
- UART_3_RX : PB11
|
|
- I2C_1_SCL : PB6
|
|
- I2C_1_SDA : PB7
|
|
- SPI_1_NSS : PA4
|
|
- SPI_1_SCK : PB3
|
|
- SPI_1_MISO : PA6
|
|
- SPI_1_MOSI : PA7
|
|
- SPI_2_NSS : PB12
|
|
- SPI_2_SCK : PB13
|
|
- SPI_2_MISO : PB14
|
|
- SPI_2_MOSI : PB15
|
|
- SPI_3_NSS : PB12
|
|
- SPI_3_SCK : PC10
|
|
- SPI_3_MISO : PC11
|
|
- SPI_3_MOSI : PC12
|
|
- PWM_2_CH1 : PA0
|
|
- USER_PB : PC13
|
|
- LD1 : PC7
|
|
- LD2 : PB7
|
|
- LD3 : PB14
|
|
- USB DM : PA11
|
|
- USB DP : PA12
|
|
|
|
System Clock
|
|
------------
|
|
|
|
Nucleo L4R5ZI System Clock could be driven by internal or external
|
|
oscillator, as well as main PLL clock. By default, the System clock is
|
|
driven by the PLL clock at 80MHz, driven by a 16MHz high speed
|
|
internal oscillator. The clock can be boosted to 120MHz if boost mode
|
|
is selected.
|
|
|
|
Serial Port
|
|
-----------
|
|
|
|
Nucleo L4R5ZI board has 5 U(S)ARTs. The Zephyr console output is
|
|
assigned to UART2. Default settings are 115200 8N1.
|
|
|
|
Network interface
|
|
-----------------
|
|
|
|
Ethernet over USB is configured as the default network interface (EEM)
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
Currently, the usual way of programming and debugging does not
|
|
exist. This will hopefully be added to a future version of the SDK. In
|
|
the meantime, the `STM32 ST-LINK utility`_ program can be used by
|
|
connecting CN1 to your PC and selecting the zephyr.bin file to flash.
|
|
|
|
.. _Nucleo L4R5ZI website:
|
|
http://www.st.com/en/evaluation-tools/nucleo-l4r5zi.html
|
|
|
|
.. _STM32 Nucleo-144 board User Manual:
|
|
http://www.st.com/resource/en/user_manual/dm00368330.pdf
|
|
|
|
.. _STM32L4R5ZI on www.st.com:
|
|
http://www.st.com/en/microcontrollers/stm32l4r5zi.html
|
|
|
|
.. _STM32L4R5 reference manual:
|
|
http://www.st.com/resource/en/reference_manual/DM00310109.pdf
|
|
|
|
.. _STM32 ST-LINK utility:
|
|
http://www.st.com/content/st_com/en/products/development-tools/software-development-tools/stm32-software-development-tools/stm32-programmers/stsw-link004.html |