281 lines
8.8 KiB
Plaintext
281 lines
8.8 KiB
Plaintext
# Copyright (c) 2022 Espressif Systems (Shanghai) Co., Ltd.
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
config SOC_ESP32S3
|
|
bool "ESP32S3"
|
|
select XTENSA
|
|
select CLOCK_CONTROL
|
|
select DYNAMIC_INTERRUPTS
|
|
select ARCH_SUPPORTS_COREDUMP
|
|
select PINCTRL
|
|
select XIP if !MCUBOOT
|
|
select HAS_ESPRESSIF_HAL
|
|
select CPU_HAS_FPU
|
|
|
|
if SOC_ESP32S3
|
|
|
|
config SOC_FAMILY_ESP32
|
|
bool
|
|
default y
|
|
|
|
config IDF_TARGET_ESP32S3
|
|
bool "ESP32S3 as target board"
|
|
default y
|
|
|
|
config ESPTOOLPY_FLASHFREQ_80M
|
|
bool
|
|
default y
|
|
|
|
config FLASH_SIZE
|
|
int
|
|
default $(dt_node_reg_size_int,/soc/flash-controller@60002000/flash@0,0)
|
|
|
|
config FLASH_BASE_ADDRESS
|
|
hex
|
|
default $(dt_node_reg_addr_hex,/soc/flash-controller@60002000/flash@0)
|
|
|
|
choice ESP32S3_RTC_CLK_SRC
|
|
prompt "RTC clock source"
|
|
default ESP32S3_RTC_CLK_SRC_INT_RC
|
|
help
|
|
Choose which clock is used as RTC clock source.
|
|
|
|
config ESP32S3_RTC_CLK_SRC_INT_RC
|
|
bool "Internal 150kHz RC oscillator"
|
|
config ESP32S3_RTC_CLK_SRC_EXT_CRYS
|
|
bool "External 32kHz crystal"
|
|
select ESP_SYSTEM_RTC_EXT_XTAL
|
|
config ESP32S3_RTC_CLK_SRC_EXT_OSC
|
|
bool "External 32kHz oscillator at 32K_XP pin"
|
|
select ESP_SYSTEM_RTC_EXT_OSC
|
|
config ESP32S3_RTC_CLK_SRC_INT_8MD256
|
|
bool "Internal 8MHz oscillator, divided by 256 (~32kHz)"
|
|
endchoice
|
|
|
|
config ESP32S3_RTC_CLK_CAL_CYCLES
|
|
int "Number of cycles for RTC_SLOW_CLK calibration"
|
|
default 3000 if ESP32S3_RTC_CLK_SRC_EXT_CRYS || ESP32S3_RTC_CLK_SRC_EXT_OSC || ESP32S3_RTC_CLK_SRC_INT_8MD256
|
|
default 1024 if ESP32S3_RTC_CLK_SRC_INT_RC
|
|
range 0 27000 if ESP32S3_RTC_CLK_SRC_EXT_CRYS || ESP32S3_RTC_CLK_SRC_EXT_OSC || ESP32S3_RTC_CLK_SRC_INT_8MD256
|
|
range 0 32766 if ESP32S3_RTC_CLK_SRC_INT_RC
|
|
help
|
|
When the startup code initializes RTC_SLOW_CLK, it can perform
|
|
calibration by comparing the RTC_SLOW_CLK frequency with main XTAL
|
|
frequency. This option sets the number of RTC_SLOW_CLK cycles measured
|
|
by the calibration routine. Higher numbers increase calibration
|
|
precision, which may be important for applications which spend a lot of
|
|
time in deep sleep. Lower numbers reduce startup time.
|
|
|
|
When this option is set to 0, clock calibration will not be performed at
|
|
startup, and approximate clock frequencies will be assumed:
|
|
|
|
- 150000 Hz if internal RC oscillator is used as clock source. For this use value 1024.
|
|
- 32768 Hz if the 32k crystal oscillator is used. For this use value 3000 or more.
|
|
In case more value will help improve the definition of the launch of the crystal.
|
|
If the crystal could not start, it will be switched to internal RC.
|
|
|
|
choice ESP32_UNIVERSAL_MAC_ADDRESSES
|
|
bool "Number of universally administered (by IEEE) MAC address"
|
|
default ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR
|
|
help
|
|
Configure the number of universally administered (by IEEE) MAC addresses.
|
|
During initialization, MAC addresses for each network interface are generated or
|
|
derived from a single base MAC address. If the number of universal MAC addresses is four,
|
|
all four interfaces (WiFi station, WiFi softap, Bluetooth and Ethernet) receive a universally
|
|
administered MAC address. These are generated sequentially by adding 0, 1, 2 and 3 (respectively)
|
|
to the final octet of the base MAC address. If the number of universal MAC addresses is two,
|
|
only two interfaces (WiFi station and Bluetooth) receive a universally administered MAC address.
|
|
These are generated sequentially by adding 0 and 1 (respectively) to the base MAC address.
|
|
The remaining two interfaces (WiFi softap and Ethernet) receive local MAC addresses.
|
|
These are derived from the universal WiFi station and Bluetooth MAC addresses, respectively.
|
|
When using the default (Espressif-assigned) base MAC address, either setting can be used.
|
|
When using a custom universal MAC address range, the correct setting will depend on the
|
|
allocation of MAC addresses in this range (either 2 or 4 per device.)
|
|
|
|
config ESP32_UNIVERSAL_MAC_ADDRESSES_TWO
|
|
bool "Two"
|
|
select ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
select ESP_MAC_ADDR_UNIVERSE_BT
|
|
|
|
config ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR
|
|
bool "Four"
|
|
select ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
select ESP_MAC_ADDR_UNIVERSE_WIFI_AP
|
|
select ESP_MAC_ADDR_UNIVERSE_BT
|
|
select ESP_MAC_ADDR_UNIVERSE_ETH
|
|
|
|
endchoice # ESP32_UNIVERSAL_MAC_ADDRESSES
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_WIFI_AP
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_WIFI_STA
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_BT
|
|
bool
|
|
|
|
config ESP_MAC_ADDR_UNIVERSE_ETH
|
|
bool
|
|
|
|
config ESP32_UNIVERSAL_MAC_ADDRESSES
|
|
int
|
|
default 2 if ESP32_UNIVERSAL_MAC_ADDRESSES_TWO
|
|
default 4 if ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR
|
|
|
|
config ESP32_PHY_MAX_WIFI_TX_POWER
|
|
int "Max WiFi/BLE TX power (dBm)"
|
|
range 10 20
|
|
default 20
|
|
help
|
|
Set maximum transmit power for WiFi radio. Actual transmit power for high
|
|
data rates may be lower than this setting.
|
|
|
|
config ESP32_PHY_MAX_TX_POWER
|
|
int
|
|
default ESP32_PHY_MAX_WIFI_TX_POWER
|
|
|
|
menu "Cache config"
|
|
|
|
choice ESP32S3_INSTRUCTION_CACHE_SIZE
|
|
prompt "Instruction cache size"
|
|
default ESP32S3_INSTRUCTION_CACHE_16KB
|
|
help
|
|
Instruction cache size to be set on application startup.
|
|
If you use 16KB instruction cache rather than 32KB instruction cache,
|
|
then the other 16KB will be managed by heap allocator.
|
|
|
|
config ESP32S3_INSTRUCTION_CACHE_16KB
|
|
bool "16KB"
|
|
config ESP32S3_INSTRUCTION_CACHE_32KB
|
|
bool "32KB"
|
|
endchoice
|
|
|
|
config ESP32S3_INSTRUCTION_CACHE_SIZE
|
|
hex
|
|
default 0x4000 if ESP32S3_INSTRUCTION_CACHE_16KB
|
|
default 0x8000 if ESP32S3_INSTRUCTION_CACHE_32KB
|
|
|
|
choice ESP32S3_ICACHE_ASSOCIATED_WAYS
|
|
prompt "Instruction cache associated ways"
|
|
default ESP32S3_INSTRUCTION_CACHE_8WAYS
|
|
help
|
|
Instruction cache associated ways to be set on application startup.
|
|
|
|
config ESP32S3_INSTRUCTION_CACHE_4WAYS
|
|
bool "4 ways"
|
|
config ESP32S3_INSTRUCTION_CACHE_8WAYS
|
|
bool "8 ways"
|
|
endchoice
|
|
|
|
config ESP32S3_ICACHE_ASSOCIATED_WAYS
|
|
int
|
|
default 4 if ESP32S3_INSTRUCTION_CACHE_4WAYS
|
|
default 8 if ESP32S3_INSTRUCTION_CACHE_8WAYS
|
|
|
|
choice ESP32S3_INSTRUCTION_CACHE_LINE_SIZE
|
|
prompt "Instruction cache line size"
|
|
default ESP32S3_INSTRUCTION_CACHE_LINE_32B
|
|
help
|
|
Instruction cache line size to be set on application startup.
|
|
|
|
config ESP32S3_INSTRUCTION_CACHE_LINE_16B
|
|
bool "16 Bytes"
|
|
depends on ESP32S3_INSTRUCTION_CACHE_16KB
|
|
config ESP32S3_INSTRUCTION_CACHE_LINE_32B
|
|
bool "32 Bytes"
|
|
endchoice
|
|
|
|
config ESP32S3_INSTRUCTION_CACHE_LINE_SIZE
|
|
int
|
|
default 16 if ESP32S3_INSTRUCTION_CACHE_LINE_16B
|
|
default 32 if ESP32S3_INSTRUCTION_CACHE_LINE_32B
|
|
|
|
config ESP32S3_INSTRUCTION_CACHE_WRAP
|
|
bool "Define instruction cache wrap mode"
|
|
help
|
|
If enabled, instruction cache will use wrap mode to read spi flash or spi ram.
|
|
The wrap length equals to ESP32S3_INSTRUCTION_CACHE_LINE_SIZE.
|
|
However, it depends on complex conditions.
|
|
|
|
choice ESP32S3_DATA_CACHE_SIZE
|
|
prompt "Data cache size"
|
|
default ESP32S3_DATA_CACHE_32KB
|
|
help
|
|
Data cache size to be set on application startup.
|
|
If you use 32KB data cache rather than 64KB data cache,
|
|
the other 32KB will be added to the heap.
|
|
|
|
config ESP32S3_DATA_CACHE_16KB
|
|
bool "16KB"
|
|
config ESP32S3_DATA_CACHE_32KB
|
|
bool "32KB"
|
|
config ESP32S3_DATA_CACHE_64KB
|
|
bool "64KB"
|
|
endchoice
|
|
|
|
config ESP32S3_DATA_CACHE_SIZE
|
|
hex
|
|
# For 16KB the actual configuration is 32kb cache, but 16kb will be reserved for heap at startup
|
|
default 0x8000 if ESP32S3_DATA_CACHE_16KB
|
|
default 0x8000 if ESP32S3_DATA_CACHE_32KB
|
|
default 0x10000 if ESP32S3_DATA_CACHE_64KB
|
|
|
|
choice ESP32S3_DCACHE_ASSOCIATED_WAYS
|
|
prompt "Data cache associated ways"
|
|
default ESP32S3_DATA_CACHE_8WAYS
|
|
help
|
|
Data cache associated ways to be set on application startup.
|
|
|
|
config ESP32S3_DATA_CACHE_4WAYS
|
|
bool "4 ways"
|
|
config ESP32S3_DATA_CACHE_8WAYS
|
|
bool "8 ways"
|
|
endchoice
|
|
|
|
config ESP32S3_DCACHE_ASSOCIATED_WAYS
|
|
int
|
|
default 4 if ESP32S3_DATA_CACHE_4WAYS
|
|
default 8 if ESP32S3_DATA_CACHE_8WAYS
|
|
|
|
choice ESP32S3_DATA_CACHE_LINE_SIZE
|
|
prompt "Data cache line size"
|
|
default ESP32S3_DATA_CACHE_LINE_32B
|
|
help
|
|
Data cache line size to be set on application startup.
|
|
|
|
config ESP32S3_DATA_CACHE_LINE_16B
|
|
bool "16 Bytes"
|
|
depends on ESP32S3_DATA_CACHE_16KB || ESP32S3_DATA_CACHE_32KB
|
|
config ESP32S3_DATA_CACHE_LINE_32B
|
|
bool "32 Bytes"
|
|
config ESP32S3_DATA_CACHE_LINE_64B
|
|
bool "64 Bytes"
|
|
endchoice
|
|
|
|
config ESP32S3_DATA_CACHE_LINE_SIZE
|
|
int
|
|
default 16 if ESP32S3_DATA_CACHE_LINE_16B
|
|
default 32 if ESP32S3_DATA_CACHE_LINE_32B
|
|
default 64 if ESP32S3_DATA_CACHE_LINE_64B
|
|
|
|
config ESP32S3_DATA_CACHE_WRAP
|
|
bool "Define data cache wrap mode"
|
|
help
|
|
If enabled, data cache will use wrap mode to read spi flash or spi ram.
|
|
The wrap length equals to ESP32S3_DATA_CACHE_LINE_SIZE.
|
|
However, it depends on complex conditions.
|
|
|
|
config MAC_BB_PD
|
|
bool "Power down MAC and baseband of Wi-Fi and Bluetooth when PHY is disabled"
|
|
depends on SOC_ESP32S3 && TICKLESS_KERNEL
|
|
default n
|
|
help
|
|
If enabled, the MAC and baseband of Wi-Fi and Bluetooth will be powered
|
|
down when PHY is disabled. Enabling this setting reduces power consumption
|
|
by a small amount but increases RAM use by approximat
|
|
|
|
endmenu # Cache config
|
|
|
|
endif # SOC_ESP32S3
|