112 lines
3.1 KiB
Plaintext
112 lines
3.1 KiB
Plaintext
# Copyright (c) 2023 Espressif Systems (Shanghai) Co., Ltd.
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
config SOC_SERIES_ESP32
|
|
select XTENSA
|
|
select CLOCK_CONTROL
|
|
select DYNAMIC_INTERRUPTS
|
|
select ARCH_HAS_GDBSTUB
|
|
select ARCH_SUPPORTS_COREDUMP
|
|
select PINCTRL
|
|
select HAS_ESPRESSIF_HAL
|
|
select CPU_HAS_FPU
|
|
select HAS_PM
|
|
select HAS_POWEROFF
|
|
|
|
if SOC_SERIES_ESP32
|
|
|
|
config ESP32_APPCPU_IRAM
|
|
hex "ESP32 APPCPU IRAM size"
|
|
depends on SOC_ESP32_PROCPU || SOC_ESP32_APPCPU
|
|
default 0x20000
|
|
help
|
|
Defines APPCPU IRAM area in bytes.
|
|
|
|
config ESP32_APPCPU_DRAM
|
|
hex "ESP32 APPCPU DRAM size"
|
|
depends on SOC_ESP32_PROCPU || SOC_ESP32_APPCPU
|
|
default 0x10000
|
|
help
|
|
Defines APPCPU DRAM area in bytes.
|
|
|
|
config SOC_ENABLE_APPCPU
|
|
bool
|
|
default y
|
|
depends on IPM && SOC_ESP32_PROCPU
|
|
depends on MBOX && SOC_ESP32_PROCPU
|
|
help
|
|
This hidden configuration lets PROCPU core to map and start APPCPU whenever IPM is enabled.
|
|
|
|
config ESP32_BT_RESERVE_DRAM
|
|
hex "Bluetooth controller reserved RAM region"
|
|
default 0xdb5c if BT
|
|
default 0
|
|
|
|
config ESP_HEAP_MEM_POOL_REGION_1_SIZE
|
|
int "Internal DRAM region 1 mempool size"
|
|
default 0 if MCUBOOT
|
|
default 1024 if SOC_ESP32_PROCPU
|
|
default 49152
|
|
help
|
|
ESP32 has two banks of size 192K and 128K which can be used
|
|
as DRAM, system heap allocates area from region 0.
|
|
This configuration can be used to add memory from region 1
|
|
to heap and can be allocated using k_malloc.
|
|
|
|
config ESP32_DEEP_SLEEP_WAKEUP_DELAY
|
|
int "Extra delay in deep sleep wake stub (in us)"
|
|
default 2000
|
|
range 0 5000
|
|
help
|
|
When ESP32 exits deep sleep, the CPU and the flash chip are powered on
|
|
at the same time. CPU will run deep sleep stub first, and then
|
|
proceed to load code from flash. Some flash chips need sufficient
|
|
time to pass between power on and first read operation. By default,
|
|
without any extra delay, this time is approximately 900us, although
|
|
some flash chip types need more than that.
|
|
|
|
By default extra delay is set to 2000us. When optimizing startup time
|
|
for applications which require it, this value may be reduced.
|
|
|
|
If you are seeing "flash read err, 1000" message printed to the
|
|
console after deep sleep reset, try increasing this value.
|
|
|
|
config ESP32_EMAC
|
|
bool
|
|
default y if ETH_ESP32
|
|
default y if MDIO_ESP32
|
|
default n
|
|
help
|
|
Hidden option to enable the ESP32 Ethernet MAC driver.
|
|
Both Ethernet and MDIO depend on this driver.
|
|
This option allows enabling MDIO independently of Ethernet.
|
|
|
|
if ESP32_EMAC
|
|
|
|
config ETH_DMA_BUFFER_SIZE
|
|
int "Ethernet DMA buffer size (Byte)"
|
|
range 256 1600
|
|
default 512
|
|
help
|
|
Set the size of each buffer used by Ethernet MAC DMA.
|
|
|
|
config ETH_DMA_RX_BUFFER_NUM
|
|
int "Amount of Ethernet DMA Rx buffers"
|
|
range 3 30
|
|
default 10
|
|
help
|
|
Number of DMA receive buffers. Each buffer's size is ETH_DMA_BUFFER_SIZE.
|
|
Larger number of buffers could increase throughput somehow.
|
|
|
|
config ETH_DMA_TX_BUFFER_NUM
|
|
int "Amount of Ethernet DMA Tx buffers"
|
|
range 3 30
|
|
default 10
|
|
help
|
|
Number of DMA transmit buffers. Each buffer's size is ETH_DMA_BUFFER_SIZE.
|
|
Larger number of buffers could increase throughput somehow.
|
|
|
|
endif # ESP32_EMAC config
|
|
|
|
endif # SOC_SERIES_ESP32
|