104 lines
3.5 KiB
ReStructuredText
104 lines
3.5 KiB
ReStructuredText
.. _spi_flash_at45_sample:
|
|
|
|
AT45 DataFlash driver sample
|
|
#############################
|
|
|
|
Overview
|
|
********
|
|
|
|
This sample shows how to use the AT45 family DataFlash driver and how to
|
|
specify devicetree nodes that enable flash chip instances to be handled
|
|
by the driver (an overlay with two sample nodes is provided).
|
|
The sample writes a defined test region in the flash memory with bytes of
|
|
increasing (and overflowing at the 8-bit range) values and then reads it back
|
|
to check if the write was successful. The starting value is also increased
|
|
in consecutive runs of the sample.
|
|
|
|
The sample have two config overlays.
|
|
The :zephyr_file:`samples/drivers/spi_flash_at45/overlay-pm.conf` enables the
|
|
device power management API which allows set device into a low power state.
|
|
The :zephyr_file:`samples/drivers/spi_flash_at45/overlay-page_layout.conf`
|
|
enables the flash page layout API which allow show the flash information.
|
|
|
|
In the default configuration, the AT45 flash driver is configured to use
|
|
the Read-Modify-Write functionality of DataFlash chips and does not perform
|
|
page erasing, as it is not needed in this case. This can be modified by
|
|
simply disabling the SPI_FLASH_AT45_USE_READ_MODIFY_WRITE option.
|
|
|
|
Requirements
|
|
************
|
|
|
|
This sample has been tested on the Nordic Semiconductor nRF9160 DK
|
|
(nrf9160dk_nrf9160) board with the AT45DB321E chip connected.
|
|
It can be easily adjusted to be usable on other boards and with other
|
|
AT45 family chips by just providing a corresponding overlay file.
|
|
|
|
Building and Running
|
|
********************
|
|
|
|
The code can be found in :zephyr_file:`samples/drivers/spi_flash_at45`.
|
|
|
|
To build and flash the application:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/drivers/spi_flash_at45
|
|
:board: nrf9160dk_nrf9160
|
|
:goals: build flash
|
|
:compact:
|
|
|
|
To build and flash with device power management enabled:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/drivers/spi_flash_at45
|
|
:board: nrf9160dk_nrf9160
|
|
:gen-args: -DOVERLAY_CONFIG=overlay-pm.conf
|
|
:goals: build flash
|
|
:compact:
|
|
|
|
To build and flash with flash page layout enabled:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/drivers/spi_flash_at45
|
|
:board: nrf9160dk_nrf9160
|
|
:gen-args: -DOVERLAY_CONFIG=overlay-page_layout.conf
|
|
:goals: build flash
|
|
:compact:
|
|
|
|
Finally, to build and flash with both device power management and flash page
|
|
layout enabled:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/drivers/spi_flash_at45
|
|
:board: nrf9160dk_nrf9160
|
|
:gen-args: -DOVERLAY_CONFIG="overlay-pm.conf overlay-page_layout.conf"
|
|
:goals: build flash
|
|
:compact:
|
|
|
|
Sample Output
|
|
=============
|
|
|
|
This is a typical output when both device power management and flash page
|
|
layout are enabled:
|
|
|
|
.. code-block:: console
|
|
|
|
DataFlash sample app on nrf9160dk_nrf9160
|
|
Using DATAFLASH_1, chip size: 4194304 bytes (page: 512)
|
|
Reading the first byte of the test region ... OK
|
|
Preparing test content starting with 0x01.
|
|
Writing the first half of the test region... OK
|
|
Writing the second half of the test region... OK
|
|
Reading the whole test region... OK
|
|
Checking the read content... OK
|
|
Putting the flash device into low power state... OK
|
|
|
|
The sample is supplied with the overlay file that specifies two instances
|
|
of AT45 family chips but only the one labeled "DATAFLASH_1" is required
|
|
for the sample to work. If the other chip is not connected, the following
|
|
log message appears, but apart from that the behavior of the sample stays
|
|
unaffected.
|
|
|
|
.. code-block:: console
|
|
|
|
[00:00:00.000,000] <err> spi_flash_at45: Wrong JEDEC ID: ff ff ff, expected: 1f 24 00
|