101 lines
2.4 KiB
Plaintext
101 lines
2.4 KiB
Plaintext
# Kconfig - SX9500 SAR proximity sensor configuration options
|
|
|
|
#
|
|
# Copyright (c) 2016 Intel Corporation
|
|
#
|
|
# Licensed under the Apache License, Version 2.0 (the "License");
|
|
# you may not use this file except in compliance with the License.
|
|
# You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS,
|
|
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
# See the License for the specific language governing permissions and
|
|
# limitations under the License.
|
|
#
|
|
|
|
menuconfig SX9500
|
|
bool "SX9500 I2C SAR Proximity Chip"
|
|
depends on SENSOR && I2C
|
|
default n
|
|
help
|
|
Enable driver for SX9500 I2C-based SAR proximity sensor.
|
|
|
|
config SX9500_DEV_NAME
|
|
string "SX9500 device name"
|
|
depends on SX9500
|
|
default "SX9500"
|
|
|
|
config SX9500_I2C_ADDR
|
|
hex "SX9500 I2C slave address"
|
|
depends on SX9500
|
|
default 0x2B
|
|
help
|
|
Specify the I2C slave address for the SX9500.
|
|
|
|
config SX9500_I2C_DEV_NAME
|
|
string "I2C master where SX9500 is connected"
|
|
depends on SX9500
|
|
default "I2C_0"
|
|
help
|
|
Specify the device name of the I2C master device to which SX9500 is
|
|
connected.
|
|
|
|
config SX9500_PROX_CHANNEL
|
|
int
|
|
default 3
|
|
depends on SX9500
|
|
prompt "Proximity channel to use"
|
|
help
|
|
The SX9500 offers 4 separate proximity channels. Choose which one
|
|
you are using. Valid numbers are 0 to 3.
|
|
|
|
choice
|
|
prompt "SX9500 trigger mode"
|
|
depends on SX9500
|
|
default SX9500_TRIGGER_GLOBAL_THREAD
|
|
|
|
config SX9500_TRIGGER_NONE
|
|
bool "No trigger"
|
|
|
|
config SX9500_TRIGGER_GLOBAL_THREAD
|
|
depends on GPIO
|
|
select SX9500_TRIGGER
|
|
bool "Use global thread"
|
|
|
|
config SX9500_TRIGGER_OWN_THREAD
|
|
depends on GPIO
|
|
select SX9500_TRIGGER
|
|
bool "Use own thread"
|
|
|
|
endchoice
|
|
|
|
config SX9500_TRIGGER
|
|
bool
|
|
depends on SX9500
|
|
|
|
config SX9500_GPIO_CONTROLLER
|
|
string "GPIO controller for SX9500 interrupt"
|
|
depends on SX9500 && SX9500_TRIGGER
|
|
default GPIO_0
|
|
help
|
|
Specify the device name of the GPIO controller the SX9500 interrupt
|
|
is connected to.
|
|
|
|
config SX9500_GPIO_PIN
|
|
int "GPIO pin for SX9500 interrupt"
|
|
depends on SX9500 && SX9500_TRIGGER
|
|
default 3
|
|
|
|
config SX9500_THREAD_STACK_SIZE
|
|
int "Sensor delayed work thread stack size"
|
|
depends on SX9500 && SX9500_TRIGGER_OWN_THREAD
|
|
default 1024
|
|
|
|
config SX9500_THREAD_PRIORITY
|
|
int "Thread priority"
|
|
depends on SX9500 && SX9500_TRIGGER_OWN_THREAD
|
|
default 10
|