111 lines
3.5 KiB
YAML
111 lines
3.5 KiB
YAML
# Copyright (c) 2023 Nordic Semiconductor ASA
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
description: |
|
|
The TI CC32XX pin controller is a singleton node responsible for controlling
|
|
pin function selection and pin properties. For example, you can
|
|
use this node to route UART0 RX to pin 55 and enable the pull-up resistor
|
|
on the pin.
|
|
|
|
The node has the 'pinctrl' node label set in your SoC's devicetree,
|
|
so you can modify it like this:
|
|
|
|
&pinctrl {
|
|
/* your modifications go here */
|
|
};
|
|
|
|
All device pin configurations should be placed in child nodes of the
|
|
'pinctrl' node, as shown in this example:
|
|
|
|
/* You can put this in places like a board-pinctrl.dtsi file in
|
|
* your board directory, or a devicetree overlay in your application.
|
|
*/
|
|
|
|
/* include pre-defined combinations for the SoC variant used by the board */
|
|
#include <dt-bindings/pinctrl/gd32f450i(g-i-k)xx-pinctrl.h>
|
|
|
|
&pinctrl {
|
|
/* configuration for the uart0 "default" state */
|
|
uart0_default: uart0_default {
|
|
/* group 1 */
|
|
group1 {
|
|
/* configure pin 55 as UART0 TX and pin 61 as UART0 CTS */
|
|
pinmux = <UART0_TX_P55>, <UART0_CTS_P61>;
|
|
};
|
|
/* group 2 */
|
|
group2 {
|
|
/* configure pin 57 as UART0 RX and pin 62 as UART0 RTS */
|
|
pinmux = <UART0_RX_P57>, <UART0_RTS_P62>;
|
|
/* both pin 57 and 62 have pull-up enabled */
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
The 'uart0_default' child node encodes the pin configurations for a
|
|
particular state of a device; in this case, the default (that is, active)
|
|
state.
|
|
|
|
As shown, pin configurations are organized in groups within each child node.
|
|
Each group can specify a list of pin function selections in the 'pinmux'
|
|
property.
|
|
|
|
A group can also specify shared pin properties common to all the specified
|
|
pins, such as the 'bias-pull-up' property in group 2. Here is a list of
|
|
supported standard pin properties:
|
|
|
|
- drive-push-pull: Push-pull drive mode (default, not required).
|
|
- drive-open-drain: Open-drain drive mode.
|
|
- bias-disable: Disable pull-up/down (default, not required).
|
|
- bias-pull-up: Enable pull-up resistor.
|
|
- bias-pull-down: Enable pull-down resistor.
|
|
- drive-strength: Configure drive strength in mA (defaults to 6mA, IC default).
|
|
|
|
Note that drive and bias options are mutually exclusive.
|
|
|
|
To link pin configurations with a device, use a pinctrl-N property for some
|
|
number N, like this example you could place in your board's DTS file:
|
|
|
|
#include "board-pinctrl.dtsi"
|
|
|
|
&uart0 {
|
|
pinctrl-0 = <&uart0_default>
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
compatible: "ti,cc32xx-pinctrl"
|
|
|
|
include: base.yaml
|
|
|
|
child-binding:
|
|
child-binding:
|
|
include:
|
|
- name: pincfg-node.yaml
|
|
property-allowlist:
|
|
- drive-push-pull
|
|
- drive-open-drain
|
|
- bias-disable
|
|
- bias-pull-down
|
|
- bias-pull-up
|
|
- drive-strength
|
|
|
|
properties:
|
|
pinmux:
|
|
required: true
|
|
type: array
|
|
description: |
|
|
An array of pins sharing the same group properties. The pins should
|
|
be defined using pre-defined macros or, alternatively, using the
|
|
TI_CC32XX_PINMUX helper macro.
|
|
|
|
drive-strength:
|
|
default: 6
|
|
enum:
|
|
- 0
|
|
- 2
|
|
- 4
|
|
- 6
|
|
- 8
|
|
- 10
|
|
- 12
|
|
- 14
|