130 lines
3.8 KiB
YAML
130 lines
3.8 KiB
YAML
# Copyright (c) 2020 Linaro Limited
|
|
# Copyright (c) 2021 Microchip Technology Inc.
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
description: |
|
|
Microchip XEC Pin controller Node
|
|
Based on pincfg-node.yaml binding.
|
|
The MCHP XEC pin controller is a singleton node responsible for controlling
|
|
pin function selection and pin properties. For example, you can use this
|
|
node to select peripheral pin functions.
|
|
|
|
The node has the 'pinctrl' node label set in your SoC's devicetree,
|
|
so you can modify it like this:
|
|
|
|
&pinctrl {
|
|
/* your modifications go here */
|
|
};
|
|
|
|
All device pin configurations should be placed in child nodes of the
|
|
'pinctrl' node, as in the spi0 example shown at the end:
|
|
|
|
A group can also specify shared pin properties common to all the specified
|
|
pins, such as the 'bias-pull-up' property in group 2. Here is a list of
|
|
supported standard pin properties:
|
|
|
|
- bias-disable: Disable pull-up/down (default behavior, not required).
|
|
- bias-pull-down: Enable pull-down resistor.
|
|
- bias-pull-up: Enable pull-up resistor.
|
|
- drive-push-pull: Output driver is push-pull (default, not required).
|
|
- drive-open-drain: Output driver is open-drain.
|
|
- output-high: Set output state high when pin configured.
|
|
- output-low: Set output state low when pin configured.
|
|
|
|
Custom pin properties for drive strength and slew rate are available:
|
|
- drive-strength
|
|
- slew-rate
|
|
|
|
Driver strength and slew rate hardware defaults vary by SoC and pin.
|
|
|
|
An example for MEC172x family, include the chip level pinctrl
|
|
DTSI file in the board level DTS:
|
|
|
|
#include <microchip/mec172x/mec172xnsz-pinctrl.dtsi>
|
|
|
|
We want to use the shared SPI port of the MEC172x QMSPI controller
|
|
and want the chip select 0 to be open-drain.
|
|
|
|
To change a pin's pinctrl default properties add a reference to the
|
|
pin in the board's DTS file and set the properties.
|
|
|
|
&spi0 {
|
|
pinctrl-0 = < &shd_cs0_n_gpio055
|
|
&shd_clk_gpio056
|
|
&shd_io0_gpio223
|
|
&shd_io1_gpio224
|
|
&shd_io3_gpio016 >;
|
|
pinctrl-names = "default";
|
|
}
|
|
|
|
&shd_cs0_n_gpio055 {
|
|
drive-open-drain;
|
|
};
|
|
|
|
compatible: "microchip,xec-pinctrl"
|
|
|
|
include: base.yaml
|
|
|
|
properties:
|
|
reg:
|
|
required: true
|
|
|
|
child-binding:
|
|
description: |
|
|
This binding gives a base representation of the Microchip XEC pins
|
|
configuration
|
|
|
|
include:
|
|
- name: pincfg-node.yaml
|
|
property-allowlist:
|
|
- bias-disable
|
|
- bias-pull-down
|
|
- bias-pull-up
|
|
- drive-push-pull
|
|
- drive-open-drain
|
|
- low-power-enable
|
|
- output-disable
|
|
- output-enable
|
|
- output-high
|
|
- output-low
|
|
|
|
properties:
|
|
pinmux:
|
|
type: int
|
|
required: true
|
|
description: Pinmux selection
|
|
|
|
slew-rate:
|
|
type: string
|
|
default: "no-change"
|
|
enum:
|
|
- "no-change"
|
|
- "low-speed"
|
|
- "high-speed"
|
|
description: |
|
|
Pin speed. The default value of slew-rate is the SoC power-on-reset
|
|
value. Please refer to the data sheet as a small number of pins
|
|
may have a different default and some pins do not implement
|
|
slew rate adjustment.
|
|
|
|
drive-strength:
|
|
type: string
|
|
default: "no-change"
|
|
enum:
|
|
- "no-change"
|
|
- "1x"
|
|
- "2x"
|
|
- "4x"
|
|
- "6x"
|
|
description: |
|
|
Pin output drive strength for PIO and PIO-24 pin types. Default
|
|
is "1x" for most pins. PIO pins are 2, 4, 8, or 12 mA. PIO-24 pins
|
|
are 4, 8, 16, or 24 mA. Please refer to the data sheet for each
|
|
pin's PIO type and default drive strength.
|
|
|
|
microchip,output-func-invert:
|
|
type: boolean
|
|
description:
|
|
Invert polarity of an output alternate function. Input functions
|
|
are not affected.
|