180 lines
3.4 KiB
Plaintext
180 lines
3.4 KiB
Plaintext
/*
|
|
* Copyright (c) 2017 Shawn Nock <shawn@monadnock.ca>
|
|
* Copyright (c) 2017 Linaro Limited
|
|
* Copyright (c) 2018 Aapo Vienamo
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <nordic/nrf52832_qfaa.dtsi>
|
|
|
|
/ {
|
|
model = "Nordic Thingy52 NRF52832";
|
|
compatible = "nordic,thingy52-nrf52832";
|
|
|
|
chosen {
|
|
zephyr,console = &uart0;
|
|
zephyr,shell-uart = &uart0;
|
|
zephyr,bt-mon-uart = &uart0;
|
|
zephyr,bt-c2h-uart = &uart0;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
zephyr,code-partition = &slot0_partition;
|
|
};
|
|
|
|
/* These aliases are provided for compatibility with samples */
|
|
aliases {
|
|
led0 = &led0;
|
|
sw0 = &button0;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
/* Lightwell RGB */
|
|
led0: led_0 {
|
|
gpios = <&sx1509b 5 GPIO_ACTIVE_LOW>;
|
|
label = "Green LED";
|
|
};
|
|
led1: led_1 {
|
|
gpios = <&sx1509b 6 GPIO_ACTIVE_LOW>;
|
|
label = "Blue LED";
|
|
};
|
|
led2: led_2 {
|
|
gpios = <&sx1509b 7 GPIO_ACTIVE_LOW>;
|
|
label = "Red LED";
|
|
};
|
|
};
|
|
|
|
buttons {
|
|
compatible = "gpio-keys";
|
|
button0: button_0 {
|
|
/* gpio flags need validation */
|
|
gpios = <&gpio0 11 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
|
|
label = "Button";
|
|
};
|
|
};
|
|
|
|
vbatt {
|
|
compatible = "voltage-divider";
|
|
io-channels = <&adc 4>;
|
|
output-ohms = <180000>;
|
|
full-ohms = <(1500000 + 180000)>;
|
|
power-gpios = <&sx1509b 4 0>;
|
|
};
|
|
};
|
|
|
|
&adc {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpiote {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
compatible = "nordic,nrf-uart";
|
|
status = "okay";
|
|
current-speed = <115200>;
|
|
tx-pin = <3>;
|
|
rx-pin = <2>;
|
|
};
|
|
|
|
&i2c0 {
|
|
compatible = "nordic,nrf-twim";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
sda-pin = <7>;
|
|
scl-pin = <8>;
|
|
|
|
sx1509b: sx1509b@3e {
|
|
compatible = "semtech,sx1509b";
|
|
reg = <0x3e>;
|
|
label = "GPIO_P0";
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
ngpios = <16>;
|
|
/* Active-low LEDs init high, all else init low */
|
|
init-out-high = <0xe0e0>;
|
|
init-out-low = <0x1f1f>;
|
|
};
|
|
|
|
lps22hb_press: lps22hb_press@5c {
|
|
compatible = "st,lps22hb-press";
|
|
reg = <0x5c>;
|
|
label = "LPS22HB";
|
|
};
|
|
|
|
hts221: hts221@5f {
|
|
compatible = "st,hts221";
|
|
reg = <0x5f>;
|
|
label = "HTS221";
|
|
drdy-gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
ccs811: ccs811@5a {
|
|
compatible = "ams,ccs811";
|
|
reg = <0x5a>;
|
|
label = "CCS811";
|
|
irq-gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
|
|
reset-gpios = <&sx1509b 11 GPIO_ACTIVE_LOW>;
|
|
wake-gpios = <&sx1509b 12 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
&i2c1 {
|
|
compatible = "nordic,nrf-twim";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
sda-pin = <14>;
|
|
scl-pin = <15>;
|
|
|
|
lis2dh12: lis2dh12@19 {
|
|
compatible = "st,lis2dh12", "st,lis2dh";
|
|
reg = <0x19>;
|
|
irq-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
|
|
label = "LIS2DH12-ACCEL";
|
|
};
|
|
};
|
|
|
|
&flash0 {
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
boot_partition: partition@0 {
|
|
label = "mcuboot";
|
|
reg = <0x00000000 0xc000>;
|
|
};
|
|
slot0_partition: partition@c000 {
|
|
label = "image-0";
|
|
reg = <0x0000C000 0x32000>;
|
|
};
|
|
slot1_partition: partition@3e000 {
|
|
label = "image-1";
|
|
reg = <0x0003E000 0x32000>;
|
|
};
|
|
scratch_partition: partition@70000 {
|
|
label = "image-scratch";
|
|
reg = <0x00070000 0xa000>;
|
|
};
|
|
|
|
/*
|
|
* The flash starting at 0x0007a000 and ending at
|
|
* 0x0007ffff (sectors 122-127) is reserved for use
|
|
* by the application.
|
|
* Storage partition will be used by FCB/LittleFS/NVS
|
|
* if enabled.
|
|
*/
|
|
storage_partition: partition@7a000 {
|
|
label = "storage";
|
|
reg = <0x0007a000 0x00006000>;
|
|
};
|
|
};
|
|
};
|