.. _smp_svr_sample:
SMP Server Sample
#################
Overview
********
This sample application implements a Simple Management Protocol (SMP) server.
SMP is a basic transfer encoding for use with the MCUmgr management protocol.
For more information about MCUmgr and SMP, please see :ref:`device_mgmt`.
This sample application supports the following mcumgr transports by default:
* Shell
* Bluetooth
* UDP
``smp_svr`` enables support for the following command groups:
* ``fs_mgmt``
* ``img_mgmt``
* ``os_mgmt``
* ``stat_mgmt``
Caveats
*******
* The MCUboot bootloader is required for ``img_mgmt`` to function
properly. More information about the Device Firmware Upgrade subsystem and
MCUboot can be found in :ref:`mcuboot`.
* The :file:`mcumgr` command-line tool only works with Bluetooth Low Energy (BLE)
on Linux and macOS. On Windows there is no support for Device Firmware
Upgrade over BLE yet.
Prerequisites
*************
Installing the mcumgr cli
=========================
To interact remotely with the management subsystem on a device, we need to have the
:file:`mcumgr` installed. Follow the instructions in the :ref:`mcumgr_cli` section
of the Management subsystem documentation.
Building a BLE Controller
=========================
.. note::
This section is only relevant for Linux users
If you want to try out Device Firmware Upgrade (DFU) over the air using
Bluetooth Low Energy (BLE) and do not have a built-in or pluggable BLE radio,
you can build one and use it following the instructions in
:ref:`bluetooth-hci-uart-bluez`.
Building and flashing MCUboot
*****************************
The below steps describe how to build and run the MCUboot bootloader.
Detailed instructions can be found in the :ref:`mcuboot` documentation page.
The Zephyr port of MCUboot is essentially a normal Zephyr application, which means that
we can build and flash it like normal using ``west``, like so:
.. code-block:: console
west build -b <board> -d build_mcuboot bootloader/mcuboot/boot/zephyr
west flash -d build_mcuboot
Substitute <board> for one of the boards supported by the sample, see
:file:`sample.yaml`.
.. _smp_svr_sample_build:
Building the sample application
*******************************
The below steps describe how to build and run the ``smp_svr`` sample in
Zephyr. The ``smp_svr`` sample comes in different flavours.
.. tabs::
.. group-tab:: Bluetooth
The sample application comes in two bluetooth flavours: a normal one and a tiny one
for resource constrained bluetooth devices.
To build the normal bluetooth sample:
.. code-block:: console
west build \
-b nrf52dk_nrf52832 \
samples/subsys/mgmt/mcumgr/smp_svr \
-- \
-DOVERLAY_CONFIG=overlay-bt.conf
And to build the tiny bluetooth sample:
.. code-block:: console
west build \
-b nrf51dk_nrf51422 \
samples/subsys/mgmt/mcumgr/smp_svr \
-- \
-DOVERLAY_CONFIG=overlay-bt-tiny.conf
.. group-tab:: Serial
To build the serial sample with file-system support:
.. code-block:: console
west build \
-b frdm_k64f \
samples/subsys/mgmt/mcumgr/smp_svr \
-- \
-DOVERLAY_CONFIG='overlay-serial.conf;overlay-fs.conf'
.. group-tab:: USB CDC_ACM
To build the serial sample with USB CDC_ACM backend:
.. code-block:: console
west build \
-b nrf52840dk_nrf52840 \
samples/subsys/mgmt/mcumgr/smp_svr \
-- \
-DOVERLAY_CONFIG=overlay-cdc.conf
.. group-tab:: Shell
To build the shell sample:
.. code-block:: console
west build \
-b frdm_k64f \
samples/subsys/mgmt/mcumgr/smp_svr \
-- \
-DOVERLAY_CONFIG='overlay-shell.conf'
.. group-tab:: UDP
The UDP transport for SMP supports both IPv4 and IPv6.
In the sample, both IPv4 and IPv6 are enabled, but they can be
enabled and disabled separately.
To build the UDP sample:
.. code-block:: console
west build \
-b frdm_k64f \
samples/subsys/mgmt/mcumgr/smp_svr \
-- \
-DOVERLAY_CONFIG=overlay-udp.conf
.. _smp_svr_sample_sign:
Signing the sample image
************************
A key feature of MCUboot is that images must be signed before they can be successfully
uploaded and run on a target. To sign images, the MCUboot tool :file:`imgtool` can be used.
To sign the sample image we built in a previous step:
.. code-block:: console
west sign -t imgtool -- --key bootloader/mcuboot/root-rsa-2048.pem
The above command creates an image file called :file:`zephyr.signed.bin` in the
build directory.
For more information on image signing and ``west sign``, see the :ref:`west-sign`
documentation.
Flashing the sample image
*************************
Upload the :file:`zephyr.signed.bin` file from the previous to image slot-0 of your
board. The location of image slot-0 varies by board, as described in
:ref:`mcuboot_partitions`.
To upload the initial image file to an empty slot-0, we simply use ``west flash``
like normal. ``west flash`` will automatically detect slot-0 address and confirm
the image.
.. code-block:: console
west flash --bin-file build/zephyr/zephyr.signed.bin
We need to explicity specify the *signed* image file, otherwise the non-signed version
will be used and the image wont be runnable.
Sample image: hello world!
==========================
The ``smp_svr`` app is ready to run. Just reset your board and test the app
with the :file:`mcumgr` command-line tool's ``echo`` functionality, which will
send a string to the remote target device and have it echo it back:
.. tabs::
.. group-tab:: Bluetooth
.. code-block:: console
sudo mcumgr --conntype ble --connstring ctlr_name=hci0,peer_name='Zephyr' echo hello
hello
.. group-tab:: Shell
.. code-block:: console
mcumgr --conntype serial --connstring "/dev/ttyACM0,baud=115200" echo hello
hello
.. group-tab:: UDP
Using IPv4:
.. code-block:: console
mcumgr --conntype udp --connstring=[192.168.1.1]:1337 echo hello
hello
And using IPv6
.. code-block:: console
mcumgr --conntype udp --connstring=[2001:db8::1]:1337 echo hello
hello
.. note::
The :file:`mcumgr` command-line tool requires a connection string in order
to identify the remote target device. In the BT sample we use a BLE-based
connection string, and you might need to modify it depending on the
BLE controller you are using.
.. note::
In the following sections, examples will use ``<connection string>`` to represent
the ``--conntype <type>`` and ``--connstring=<string>`` :file:`mcumgr` parameters.
Device Firmware Upgrade (DFU)
*****************************
Now that the SMP server is running on your board and you are able to communicate
with it using :file:`mcumgr`, you might want to test what is commonly called
"OTA DFU", or Over-The-Air Device Firmware Upgrade. This works for both BT and UDP.
The general sequence of a DFU process is as follows:
* Build an MCUboot enabled application, see :ref:`smp_svr_sample_build`
* Sign the application image, see :ref:`smp_svr_sample_sign`
* Upload the signed image using :file:`mcumgr`
* Listing the images on the device using :file:`mcumgr`
* Mark the uploaded image for testing using :file:`mcumgr`
* Reset the device remotely using :file:`mcumgr`
* Confirm the uploaded image using :file:`mcumgr` (optional)
Upload the signed image
=======================
To upload the signed image, use the following command:
.. code-block:: console
sudo mcumgr <connection string> image upload build/zephyr/zephyr.signed.bin
.. note::
At the beginning of the upload process, the target might start erasing
the image slot, taking several dozen seconds for some targets. This might
cause an NMP timeout in the management protocol tool. Use the
``-t <timeout-in-seconds`` option to increase the response timeout for the
``mcumgr`` command line tool if this occurs.
List the images
===============
We can now obtain a list of images (slot-0 and slot-1) present in the remote
target device by issuing the following command:
.. code-block:: console
sudo mcumgr <connection string> image list
This should print the status and hash values of each of the images present.
Test the image
==============
In order to instruct MCUboot to swap the images we need to test the image first,
making sure it boots:
.. code-block:: console
sudo mcumgr <connection string> image test <hash of slot-1 image>
Now MCUBoot will swap the image on the next reset.
.. note::
There is not yet any way of getting the image hash without actually uploading the
image and getting the hash by using the ``image list`` command of :file:`mcumgr`.
Reset remotely
==============
We can reset the device remotely to observe (use the console output) how
MCUboot swaps the images:
.. code-block:: console
sudo mcumgr <connection string> reset
Upon reset MCUboot will swap slot-0 and slot-1.
Confirm new image
=================
The new image is now loaded into slot-0, but it will be swapped back into slot-1
on the next reset unless the image is confirmed. To confirm the new image:
.. code-block:: console
sudo mcumgr <connection string> image confirm
Note that if you try to send the very same image that is already flashed in
slot-0 then the procedure will not complete successfully since the hash values
for both slots will be identical.
464d9130d5