162 lines
5.9 KiB
ReStructuredText
162 lines
5.9 KiB
ReStructuredText
.. _hexiwear_kw40z:
|
|
|
|
Hexiwear KW40Z
|
|
##############
|
|
|
|
Overview
|
|
********
|
|
|
|
See :ref:`hexiwear_k64` for a general overview of the Hexiwear board and the
|
|
main application SoC, the K64. The KW40Z is a secondary SoC on the board that
|
|
provides wireless connectivity with a multimode BLE and 802.15.4 radio.
|
|
|
|
For more information about the KW40Z SoC:
|
|
|
|
- `KW40Z Website`_
|
|
- `KW40Z Datasheet`_
|
|
- `KW40Z Reference Manual`_
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The hexiwear_kw40z board configuration supports the following hardware features:
|
|
|
|
+-----------+------------+-------------------------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+=====================================+
|
|
| NVIC | on-chip | nested vector interrupt controller |
|
|
+-----------+------------+-------------------------------------+
|
|
| SYSTICK | on-chip | systick |
|
|
+-----------+------------+-------------------------------------+
|
|
| PINMUX | on-chip | pinmux |
|
|
+-----------+------------+-------------------------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+-------------------------------------+
|
|
| ADC | on-chip | adc |
|
|
+-----------+------------+-------------------------------------+
|
|
| UART | on-chip | serial port-polling; |
|
|
| | | serial port-interrupt |
|
|
+-----------+------------+-------------------------------------+
|
|
| RTT | on-chip | console |
|
|
+-----------+------------+-------------------------------------+
|
|
| FLASH | on-chip | soc flash |
|
|
+-----------+------------+-------------------------------------+
|
|
|
|
The default configuration can be found in the defconfig file:
|
|
|
|
``boards/arm/hexiwear_kw40z/hexiwear_kw40z_defconfig``
|
|
|
|
Other hardware features are not currently supported by the port.
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
The KW40Z SoC has three pairs of pinmux/gpio controllers, but only one is
|
|
currently enabled (PORTC/GPIOC) for the hexiwear_kw40z board.
|
|
|
|
+-------+-----------------+---------------------------+
|
|
| Name | Function | Usage |
|
|
+=======+=================+===========================+
|
|
| PTB1 | ADC | ADC0 channel 1 |
|
|
+-------+-----------------+---------------------------+
|
|
| PTC6 | UART0_RX | UART BT HCI |
|
|
+-------+-----------------+---------------------------+
|
|
| PTC7 | UART0_TX | UART BT HCI |
|
|
+-------+-----------------+---------------------------+
|
|
|
|
System Clock
|
|
============
|
|
|
|
The KW40Z SoC is configured to use the 32 MHz external oscillator on the board
|
|
with the on-chip FLL to generate a 40 MHz system clock.
|
|
|
|
Serial Port
|
|
===========
|
|
|
|
The KW40Z SoC has one UART, which is used for BT HCI. The console is available
|
|
using `Segger RTT`_.
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
The Hexiwear docking station includes the :ref:`nxp_opensda` serial and debug
|
|
adapter built into the board to provide debugging, flash programming, and
|
|
serial communication over USB.
|
|
|
|
To use the pyOCD tools with OpenSDA, follow the instructions in the
|
|
:ref:`nxp_opensda_pyocd` page using the `DAPLink Hexiwear Firmware`_. The pyOCD
|
|
tools are not the default for this board, therefore it is necessary to set
|
|
``OPENSDA_FW=daplink`` explicitly in the environment when programming and
|
|
debugging.
|
|
|
|
To use the Segger J-Link tools with OpenSDA, follow the instructions in the
|
|
:ref:`nxp_opensda_jlink` page using the `Segger J-Link OpenSDA V2.1 Firmware`_.
|
|
The Segger J-Link tools are the default for this board, therefore it is not
|
|
necessary to set ``OPENSDA_FW=jlink`` explicitly when using the usual
|
|
programming and debugging mechanisms.
|
|
|
|
With these mechanisms, applications for the ``hexiwear_kw40z`` board
|
|
configuration can be built and flashed in the usual way (see
|
|
:ref:`build_an_application` and :ref:`application_run` for more
|
|
details).
|
|
|
|
Because `Segger RTT`_ is required for a console to KW40Z, the J-Link tools are
|
|
recommended.
|
|
|
|
Flashing
|
|
========
|
|
|
|
The Segger J-Link firmware does not support command line flashing, therefore
|
|
the usual ``flash`` build target is not supported.
|
|
|
|
Debugging
|
|
=========
|
|
|
|
This example uses the :ref:`hello_world` sample with the
|
|
:ref:`nxp_opensda_jlink` tools. This builds the Zephyr application,
|
|
invokes the J-Link GDB server, attaches a GDB client, and programs the
|
|
application to flash. It will leave you at a gdb prompt.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: hexiwear_kw40z
|
|
:goals: debug
|
|
|
|
In a second terminal, open telnet:
|
|
|
|
.. code-block:: console
|
|
|
|
$ telnet localhost 19021
|
|
Trying 127.0.0.1...
|
|
Connected to localhost.
|
|
Escape character is '^]'.
|
|
SEGGER J-Link V6.14b - Real time terminal output
|
|
J-Link OpenSDA 2 compiled Feb 28 2017 19:27:57 V1.0, SN=621000000
|
|
Process: JLinkGDBServer
|
|
|
|
Continue program execution in GDB, then in the telnet terminal you should see:
|
|
|
|
.. code-block:: console
|
|
|
|
***** BOOTING ZEPHYR OS v1.7.99 - BUILD: Apr 6 2017 21:09:52 *****
|
|
Hello World! arm
|
|
|
|
|
|
.. _KW40Z Website:
|
|
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/kinetis-cortex-m-mcus/w-series-wireless-m0-plus-m4/kinetis-kw40z-2.4-ghz-dual-mode-ble-and-802.15.4-wireless-radio-microcontroller-mcu-based-on-arm-cortex-m0-plus-core:KW40Z
|
|
|
|
.. _KW40Z Datasheet:
|
|
http://www.nxp.com/assets/documents/data/en/data-sheets/MKW40Z160.pdf
|
|
|
|
.. _KW40Z Reference Manual:
|
|
http://www.nxp.com/assets/documents/data/en/reference-manuals/MKW40Z160RM.pdf
|
|
|
|
.. _Segger RTT:
|
|
https://www.segger.com/jlink-rtt.html
|
|
|
|
.. _DAPLink Hexiwear Firmware:
|
|
https://github.com/MikroElektronika/HEXIWEAR/blob/master/HW/HEXIWEAR_DockingStation/HEXIWEAR_DockingStation_DAPLINK_FW.bin
|
|
|
|
.. _Segger J-Link OpenSDA V2.1 Firmware:
|
|
https://www.segger.com/downloads/jlink/OpenSDA_V2_1.bin
|