87 lines
2.9 KiB
ReStructuredText
87 lines
2.9 KiB
ReStructuredText
.. _led_ws2812_sample:
|
|
|
|
WS2812 Sample Application
|
|
#########################
|
|
|
|
Overview
|
|
********
|
|
|
|
This sample application demonstrates basic usage of the WS2812 LED
|
|
strip driver, for controlling LED strips using WS2812, WS2812b,
|
|
SK6812, Everlight B1414 and compatible driver chips.
|
|
|
|
Requirements
|
|
************
|
|
|
|
.. _NeoPixel Ring 12 from AdaFruit: https://www.adafruit.com/product/1643
|
|
.. _74AHCT125: https://cdn-shop.adafruit.com/datasheets/74AHC125.pdf
|
|
|
|
- LED strip using WS2812 or compatible, such as the `NeoPixel Ring 12
|
|
from AdaFruit`_.
|
|
|
|
- Note that 5V communications may require a level translator, such as the
|
|
`74AHCT125`_.
|
|
|
|
- LED power strip supply. It's fine to power the LED strip off of your board's
|
|
IO voltage level even if that's below 5V; the LEDs will simply be dimmer in
|
|
this case.
|
|
|
|
Wiring
|
|
******
|
|
|
|
#. Ensure your Zephyr board, and the LED strip share a common ground.
|
|
#. Connect the LED strip control pin (either SPI MOSI or GPIO) from your board
|
|
to the data input pin of the first WS2812 IC in the strip.
|
|
#. Power the LED strip at an I/O level compatible with the control pin signals.
|
|
|
|
Building and Running
|
|
********************
|
|
|
|
.. _blog post on WS2812 timing: https://wp.josh.com/2014/05/13/ws2812-neopixels-are-not-so-finicky-once-you-get-to-know-them/
|
|
|
|
This sample's source directory is :zephyr_file:`samples/drivers/led_ws2812/`.
|
|
|
|
To make sure the sample is set up properly for building, you must:
|
|
|
|
- select the correct WS2812 driver backend for your SoC. This currently should
|
|
be :kconfig:`CONFIG_WS2812_STRIP_SPI` unless you are using an nRF51 SoC, in
|
|
which case it will be :kconfig:`CONFIG_WS2812_STRIP_GPIO`.
|
|
|
|
- create a ``led-strip`` :ref:`devicetree alias <dt-alias-chosen>`, which
|
|
refers to a node in your :ref:`devicetree <dt-guide>` with a
|
|
``worldsemi,ws2812-spi`` or ``worldsemi,ws2812-gpio`` compatible. The node
|
|
must be properly configured for the driver backend (SPI or GPIO) and daisy
|
|
chain length (number of WS2812 chips).
|
|
|
|
For example devicetree configurations for each compatible, see
|
|
:zephyr_file:`samples/drivers/led_ws2812/boards/nrf52dk_nrf52832.overlay` and
|
|
:zephyr_file:`samples/drivers/led_ws2812/boards/nrf51dk_nrf51422.overlay`.
|
|
|
|
Some boards are already supported out of the box; see the :file:`boards`
|
|
directory for this sample for details.
|
|
|
|
Then build and flash the application:
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/drivers/led_ws2812
|
|
:board: <board>
|
|
:goals: flash
|
|
:compact:
|
|
|
|
When you connect to your board's serial console, you should see the
|
|
following output:
|
|
|
|
.. code-block:: none
|
|
|
|
***** Booting Zephyr OS build v2.1.0-rc1-191-gd2466cdaf045 *****
|
|
[00:00:00.005,920] <inf> main: Found LED strip device WS2812
|
|
[00:00:00.005,950] <inf> main: Displaying pattern on strip
|
|
|
|
References
|
|
**********
|
|
|
|
- `RGB LED strips: an overview <http://nut-bolt.nl/2012/rgb-led-strips/>`_
|
|
- `74AHCT125 datasheet
|
|
<https://cdn-shop.adafruit.com/datasheets/74AHC125.pdf>`_
|
|
- An excellent `blog post on WS2812 timing`_.
|