196 lines
3.4 KiB
Plaintext
196 lines
3.4 KiB
Plaintext
/*
|
|
* Copyright (c) 2017 Linaro Limited
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <st/l4/stm32l476Xg.dtsi>
|
|
#include <st/l4/stm32l476r(c-e-g)tx-pinctrl.dtsi>
|
|
#include "arduino_r3_connector.dtsi"
|
|
#include "st_morpho_connector.dtsi"
|
|
#include <zephyr/dt-bindings/input/input-event-codes.h>
|
|
|
|
/ {
|
|
model = "STMicroelectronics STM32L476RG-NUCLEO board";
|
|
compatible = "st,stm32l476rg-nucleo";
|
|
|
|
chosen {
|
|
zephyr,console = &usart2;
|
|
zephyr,shell-uart = &usart2;
|
|
zephyr,sram = &sram0;
|
|
zephyr,flash = &flash0;
|
|
};
|
|
|
|
leds: leds {
|
|
compatible = "gpio-leds";
|
|
green_led_2: led_2 {
|
|
gpios = <&gpioa 5 GPIO_ACTIVE_HIGH>;
|
|
label = "User LD2";
|
|
};
|
|
};
|
|
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
user_button: button {
|
|
label = "User";
|
|
gpios = <&gpioc 13 GPIO_ACTIVE_LOW>;
|
|
zephyr,code = <INPUT_KEY_0>;
|
|
};
|
|
};
|
|
|
|
aliases {
|
|
led0 = &green_led_2;
|
|
sw0 = &user_button;
|
|
volt-sensor0 = &vref;
|
|
volt-sensor1 = &vbat;
|
|
};
|
|
};
|
|
|
|
&clk_lsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&clk_lse {
|
|
status = "okay";
|
|
};
|
|
|
|
&clk_hsi {
|
|
status = "okay";
|
|
};
|
|
|
|
&pll {
|
|
div-m = <1>;
|
|
mul-n = <20>;
|
|
div-r = <4>;
|
|
clocks = <&clk_hsi>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rcc {
|
|
clocks = <&pll>;
|
|
clock-frequency = <DT_FREQ_M(80)>;
|
|
ahb-prescaler = <1>;
|
|
apb1-prescaler = <1>;
|
|
apb2-prescaler = <1>;
|
|
};
|
|
|
|
stm32_lp_tick_source: &lptim1 {
|
|
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x80000000>,
|
|
<&rcc STM32_SRC_LSI LPTIM1_SEL(1)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart1 {
|
|
pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart2 {
|
|
pinctrl-0 = <&usart2_tx_pa2 &usart2_rx_pa3>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
status = "okay";
|
|
};
|
|
|
|
&usart3 {
|
|
pinctrl-0 = <&usart3_tx_pb10 &usart3_rx_pb11>;
|
|
pinctrl-names = "default";
|
|
current-speed = <115200>;
|
|
};
|
|
|
|
&i2c1 {
|
|
pinctrl-0 = <&i2c1_scl_pb8 &i2c1_sda_pb9>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&i2c3 {
|
|
pinctrl-0 = <&i2c3_scl_pc0 &i2c3_sda_pc1>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
clock-frequency = <I2C_BITRATE_FAST>;
|
|
};
|
|
|
|
&spi1 {
|
|
pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>;
|
|
pinctrl-names = "default";
|
|
cs-gpios = <&gpiob 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&spi2 {
|
|
pinctrl-0 = <&spi2_nss_pb12 &spi2_sck_pb13
|
|
&spi2_miso_pb14 &spi2_mosi_pb15>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&spi3 {
|
|
/* SPI3 on the ST Morpho Connector CN7 pins 17, 1, 2, 3*/
|
|
pinctrl-0 = <&spi3_nss_pa15 &spi3_sck_pc10
|
|
&spi3_miso_pc11 &spi3_mosi_pc12>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&timers2 {
|
|
status = "okay";
|
|
|
|
pwm2: pwm {
|
|
status = "okay";
|
|
pinctrl-0 = <&tim2_ch3_pb10>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&timers3 {
|
|
st,prescaler = <10000>;
|
|
status = "okay";
|
|
|
|
pwm3: pwm {
|
|
status = "okay";
|
|
pinctrl-0 = <&tim3_ch1_pb4>;
|
|
pinctrl-names = "default";
|
|
};
|
|
};
|
|
|
|
&rtc {
|
|
clocks = <&rcc STM32_CLOCK_BUS_APB1 0x10000000>,
|
|
<&rcc STM32_SRC_LSI RTC_SEL(2)>;
|
|
status = "okay";
|
|
};
|
|
|
|
&adc1 {
|
|
pinctrl-0 = <&adc1_in1_pc0>;
|
|
pinctrl-names = "default";
|
|
st,adc-clock-source = <SYNC>;
|
|
st,adc-prescaler = <4>;
|
|
status = "okay";
|
|
};
|
|
|
|
&vref {
|
|
status = "okay";
|
|
};
|
|
|
|
&vbat {
|
|
status = "okay";
|
|
};
|
|
|
|
&flash0 {
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/* Set 32KB of storage at the end of 1024KB flash */
|
|
storage_partition: partition@f8000 {
|
|
label = "storage";
|
|
reg = <0x000f8000 DT_SIZE_K(32)>;
|
|
};
|
|
};
|
|
};
|