174 lines
4.0 KiB
Plaintext
174 lines
4.0 KiB
Plaintext
/*
|
|
* Copyright (c) 2021 Nordic Semiconductor ASA
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include <nordic/nrf5340_cpunet_qkaa.dtsi>
|
|
#include "thingy53_nrf5340_cpunet-pinctrl.dtsi"
|
|
#include <zephyr/dt-bindings/input/input-event-codes.h>
|
|
|
|
/ {
|
|
model = "Nordic Thingy53 NRF5340 Network";
|
|
compatible = "nordic,thingy53-nrf5340-cpunet";
|
|
|
|
chosen {
|
|
zephyr,console = &uart0;
|
|
zephyr,shell-uart = &uart0;
|
|
zephyr,uart-mcumgr = &uart0;
|
|
zephyr,bt-mon-uart = &uart0;
|
|
zephyr,bt-c2h-uart = &uart0;
|
|
zephyr,bt-hci-ipc = &ipc0;
|
|
nordic,802154-spinel-ipc = &ipc0;
|
|
zephyr,sram = &sram1;
|
|
zephyr,flash = &flash1;
|
|
zephyr,code-partition = &slot0_partition;
|
|
zephyr,ieee802154 = &ieee802154;
|
|
};
|
|
|
|
buttons {
|
|
compatible = "gpio-keys";
|
|
button0: button_0 {
|
|
gpios = <&gpio1 14 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
|
|
label = "Push button 1";
|
|
zephyr,code = <INPUT_KEY_0>;
|
|
};
|
|
button1: button_1 {
|
|
gpios = <&gpio1 13 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
|
|
label = "Push button 2";
|
|
zephyr,code = <INPUT_KEY_1>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
red_led: led_1 {
|
|
gpios = <&gpio1 8 (GPIO_PULL_DOWN | GPIO_ACTIVE_HIGH)>;
|
|
label = "RGB red LED";
|
|
};
|
|
green_led: led_2 {
|
|
gpios = <&gpio1 6 (GPIO_PULL_DOWN | GPIO_ACTIVE_HIGH)>;
|
|
label = "RGB green LED";
|
|
};
|
|
blue_led: led_3 {
|
|
gpios = <&gpio1 7 (GPIO_PULL_DOWN | GPIO_ACTIVE_HIGH)>;
|
|
label = "RGB blue LED";
|
|
};
|
|
};
|
|
|
|
nrf_radio_fem: fem {
|
|
compatible = "nordic,nrf21540-fem";
|
|
rx-en-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
|
|
mode-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
|
|
pdn-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
|
|
tx-en-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
|
|
spi-if = <&nrf_radio_fem_spi>;
|
|
supply-voltage-mv = <3000>;
|
|
};
|
|
|
|
edge_connector: connector {
|
|
compatible = "nordic-thingy53-edge-connector";
|
|
#gpio-cells = <2>;
|
|
gpio-map-mask = <0xffffffff 0xffffffc0>;
|
|
gpio-map-pass-thru = <0 0x3f>;
|
|
gpio-map = <5 0 &gpio1 1 0>, /* P5, P1.01/GRANT */
|
|
<6 0 &gpio1 0 0>, /* P6, P1.00/REQ */
|
|
<8 0 &gpio0 5 0>, /* P8, P0.05/AIN1 */
|
|
<9 0 &gpio0 4 0>, /* P9, P0.04/AIN0 */
|
|
<15 0 &gpio0 8 0>, /* P15, P0.08/TRACEDATA3 */
|
|
<16 0 &gpio0 9 0>, /* P16, P0.09/TRACEDATA2 */
|
|
<17 0 &gpio0 10 0>, /* P17, P0.10/TRACEDATA1 */
|
|
<18 0 &gpio0 11 0>, /* P18, P0.11/TRACEDATA0 */
|
|
<19 0 &gpio0 12 0>; /* P19, P0.12/TRACECLK */
|
|
};
|
|
|
|
aliases {
|
|
sw0 = &button0;
|
|
sw1 = &button1;
|
|
led0 = &red_led;
|
|
led1 = &green_led;
|
|
led2 = &blue_led;
|
|
watchdog0 = &wdt;
|
|
};
|
|
};
|
|
|
|
&gpiote {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&gpio1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&uart0 {
|
|
compatible = "nordic,nrf-uarte";
|
|
status = "disabled";
|
|
current-speed = <115200>;
|
|
pinctrl-0 = <&uart0_default>;
|
|
pinctrl-1 = <&uart0_sleep>;
|
|
pinctrl-names = "default", "sleep";
|
|
};
|
|
|
|
/* Disabled by default as shares same GPIO lines as SPI peripherals on application core */
|
|
fem_spi: &spi0 {
|
|
status = "disabled";
|
|
cs-gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
|
|
pinctrl-0 = <&spi0_default>;
|
|
pinctrl-1 = <&spi0_sleep>;
|
|
pinctrl-names = "default", "sleep";
|
|
|
|
nrf_radio_fem_spi: nrf21540_fem_spi@0 {
|
|
compatible = "nordic,nrf21540-fem-spi";
|
|
status = "disabled";
|
|
reg = <0>;
|
|
spi-max-frequency = <8000000>;
|
|
};
|
|
};
|
|
|
|
&radio {
|
|
/* Uncomment to enable SPI interface for FEM */
|
|
/* fem = <&nrf_radio_fem>; */
|
|
};
|
|
|
|
&flash1 {
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
boot_partition: partition@0 {
|
|
label = "mcuboot";
|
|
reg = <0x00000000 0xc000>;
|
|
};
|
|
slot0_partition: partition@c000 {
|
|
label = "image-0";
|
|
reg = <0x0000C000 0x12000>;
|
|
};
|
|
slot1_partition: partition@1e000 {
|
|
label = "image-1";
|
|
reg = <0x0001E000 0x12000>;
|
|
};
|
|
scratch_partition: partition@30000 {
|
|
label = "image-scratch";
|
|
reg = <0x00030000 0xa000>;
|
|
};
|
|
storage_partition: partition@3a000 {
|
|
label = "storage";
|
|
reg = <0x0003a000 0x6000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ieee802154 {
|
|
status = "okay";
|
|
};
|
|
|
|
/* Include default shared RAM configuration file */
|
|
#include <common/nordic/nrf5340_shared_sram_partition.dtsi>
|