204 lines
6.9 KiB
ReStructuredText
204 lines
6.9 KiB
ReStructuredText
.. _nrf9161dk_nrf9161:
|
|
|
|
nRF9161 DK
|
|
##########
|
|
|
|
Overview
|
|
********
|
|
|
|
The nRF9161 DK (PCA10153) is a single-board development kit for evaluation and
|
|
development on the nRF9161 SiP for DECT NR+ and LTE-M/NB-IoT with GNSS. The ``nrf9161dk/nrf9161``
|
|
board configuration provides support for the Nordic Semiconductor nRF9161 ARM
|
|
Cortex-M33F CPU with ARMv8-M Security Extension and the following devices:
|
|
|
|
* :abbr:`ADC (Analog to Digital Converter)`
|
|
* CLOCK
|
|
* FLASH
|
|
* :abbr:`GPIO (General Purpose Input Output)`
|
|
* :abbr:`I2C (Inter-Integrated Circuit)`
|
|
* :abbr:`MPU (Memory Protection Unit)`
|
|
* :abbr:`NVIC (Nested Vectored Interrupt Controller)`
|
|
* :abbr:`PWM (Pulse Width Modulation)`
|
|
* :abbr:`RTC (nRF RTC System Clock)`
|
|
* Segger RTT (RTT Console)
|
|
* :abbr:`SPI (Serial Peripheral Interface)`
|
|
* :abbr:`UARTE (Universal asynchronous receiver-transmitter with EasyDMA)`
|
|
* :abbr:`WDT (Watchdog Timer)`
|
|
* :abbr:`IDAU (Implementation Defined Attribution Unit)`
|
|
|
|
More information about the board can be found at the
|
|
`nRF9161 DK website`_. `nRF9161 Product Specification`_
|
|
contains the processor's information and the datasheet.
|
|
|
|
|
|
Hardware
|
|
********
|
|
|
|
nRF9161 DK has two external oscillators. The frequency of
|
|
the slow clock is 32.768 kHz. The frequency of the main clock
|
|
is 32 MHz.
|
|
|
|
Supported Features
|
|
==================
|
|
|
|
The ``nrf9161dk/nrf9161`` board configuration supports the following
|
|
hardware features:
|
|
|
|
+-----------+------------+----------------------+
|
|
| Interface | Controller | Driver/Component |
|
|
+===========+============+======================+
|
|
| ADC | on-chip | adc |
|
|
+-----------+------------+----------------------+
|
|
| CLOCK | on-chip | clock_control |
|
|
+-----------+------------+----------------------+
|
|
| FLASH | on-chip | flash |
|
|
+-----------+------------+----------------------+
|
|
| FLASH | external | spi |
|
|
+-----------+------------+----------------------+
|
|
| GPIO | on-chip | gpio |
|
|
+-----------+------------+----------------------+
|
|
| GPIO | external | i2c |
|
|
+-----------+------------+----------------------+
|
|
| I2C(M) | on-chip | i2c |
|
|
+-----------+------------+----------------------+
|
|
| MPU | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| NVIC | on-chip | arch/arm |
|
|
+-----------+------------+----------------------+
|
|
| PWM | on-chip | pwm |
|
|
+-----------+------------+----------------------+
|
|
| RTC | on-chip | system clock |
|
|
+-----------+------------+----------------------+
|
|
| RTT | nRF53 | console |
|
|
+-----------+------------+----------------------+
|
|
| SPI(M/S) | on-chip | spi |
|
|
+-----------+------------+----------------------+
|
|
| SPU | on-chip | system protection |
|
|
+-----------+------------+----------------------+
|
|
| UARTE | on-chip | serial |
|
|
+-----------+------------+----------------------+
|
|
| WDT | on-chip | watchdog |
|
|
+-----------+------------+----------------------+
|
|
|
|
|
|
.. _nrf9161dk_additional_hardware:
|
|
|
|
Other hardware features have not been enabled yet for this board.
|
|
See `nRF9161 DK website`_ and `nRF9161 Product Specification`_
|
|
for a complete list of nRF9161 DK board hardware features.
|
|
|
|
Connections and IOs
|
|
===================
|
|
|
|
LED
|
|
---
|
|
|
|
* LED1 (green) = P0.0
|
|
* LED2 (green) = P0.1
|
|
* LED3 (green) = P0.4
|
|
* LED4 (green) = P0.5
|
|
|
|
Push buttons and Switches
|
|
-------------------------
|
|
|
|
* BUTTON1 = P0.8
|
|
* BUTTON2 = P0.9
|
|
* SWITCH1 = P0.18
|
|
* SWITCH2 = P0.19
|
|
* BOOT = SW5 = boot/reset
|
|
|
|
Security components
|
|
===================
|
|
|
|
- Implementation Defined Attribution Unit (`IDAU`_). The IDAU is implemented
|
|
with the System Protection Unit and is used to define secure and non-secure
|
|
memory maps. By default, all of the memory space (Flash, SRAM, and
|
|
peripheral address space) is defined to be secure accessible only.
|
|
- Secure boot.
|
|
|
|
|
|
Programming and Debugging
|
|
*************************
|
|
|
|
``nrf9161dk/nrf9161`` supports the Armv8m Security Extension, and by default boots
|
|
in the Secure state.
|
|
|
|
Building Secure/Non-Secure Zephyr applications with Arm |reg| TrustZone |reg|
|
|
=============================================================================
|
|
|
|
The process requires the following steps:
|
|
|
|
1. Build the Secure Zephyr application using ``-DBOARD=nrf9161dk/nrf9161`` and
|
|
``CONFIG_TRUSTED_EXECUTION_SECURE=y`` in the application project configuration file.
|
|
2. Build the Non-Secure Zephyr application using ``-DBOARD=nrf9161dk/nrf9161/ns``.
|
|
3. Merge the two binaries together.
|
|
|
|
When building a Secure/Non-Secure application, the Secure application will
|
|
have to set the IDAU (SPU) configuration to allow Non-Secure access to all
|
|
CPU resources utilized by the Non-Secure application firmware. SPU
|
|
configuration shall take place before jumping to the Non-Secure application.
|
|
|
|
Building a Secure only application
|
|
==================================
|
|
|
|
Build the Zephyr app in the usual way (see :ref:`build_an_application`
|
|
and :ref:`application_run`), using ``-DBOARD=nrf9161dk/nrf9161``.
|
|
|
|
Flashing
|
|
========
|
|
|
|
Follow the instructions in the :ref:`nordic_segger` page to install
|
|
and configure all the necessary software. Further information can be
|
|
found in :ref:`nordic_segger_flashing`. Then build and flash
|
|
applications as usual (see :ref:`build_an_application` and
|
|
:ref:`application_run` for more details).
|
|
|
|
Here is an example for the :zephyr:code-sample:`hello_world` application.
|
|
|
|
First, run your favorite terminal program to listen for output.
|
|
|
|
.. code-block:: console
|
|
|
|
$ minicom -D <tty_device> -b 115200
|
|
|
|
Replace :code:`<tty_device>` with the port where the nRF9161 DK
|
|
can be found. For example, under Linux, :code:`/dev/ttyACM0`.
|
|
|
|
Then build and flash the application in the usual way.
|
|
|
|
.. zephyr-app-commands::
|
|
:zephyr-app: samples/hello_world
|
|
:board: nrf9161dk/nrf9161
|
|
:goals: build flash
|
|
|
|
Debugging
|
|
=========
|
|
|
|
Refer to the :ref:`nordic_segger` page to learn about debugging Nordic boards with a
|
|
Segger IC.
|
|
|
|
|
|
Testing the LEDs and buttons in the nRF9161 DK
|
|
**********************************************
|
|
|
|
There are 2 samples that allow you to test that the buttons (switches) and LEDs on
|
|
the board are working properly with Zephyr:
|
|
|
|
* :zephyr:code-sample:`blinky`
|
|
* :zephyr:code-sample:`button`
|
|
|
|
You can build and flash the examples to make sure Zephyr is running correctly on
|
|
your board. The button and LED definitions can be found in
|
|
:zephyr_file:`boards/nordic/nrf9161dk/nrf9161dk_nrf9161_common.dtsi`.
|
|
|
|
References
|
|
**********
|
|
|
|
.. target-notes::
|
|
|
|
.. _IDAU:
|
|
https://developer.arm.com/docs/100690/latest/attribution-units-sau-and-idau
|
|
.. _nRF9161 DK website: https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF9161-DK
|
|
.. _nRF9161 Product Specification: https://docs.nordicsemi.com/bundle/ps_nrf9161/page/nRF9161_html5_keyfeatures.html
|
|
.. _Trusted Firmware M: https://www.trustedfirmware.org/projects/tf-m/
|