# Kconfig.bma280 - BMA280 Three Axis Accelerometer configuration options # # Copyright (c) 2016 Intel Corporation # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # menuconfig BMA280 bool prompt "BMA280 Three Axis Accelerometer Family" depends on SENSOR && I2C default n help Enable driver for BMA280 I2C-based triaxial accelerometer sensor family. config BMA280_SYS_LOG_LEVEL int "BMA280 Gyro Log level" depends on SYS_LOG && BMA280 default 0 range 0 4 help Sets log level for BMA280 driver. Levels are: 0 OFF, do not write 1 ERROR, only write SYS_LOG_ERR 2 WARNING, write SYS_LOG_WRN in addition to previous level 3 INFO, write SYS_LOG_INF in addition to previous levels 4 DEBUG, write SYS_LOG_DBG in addition to previous levels choice prompt "Chip type" depends on BMA280 default BMA280_CHIP_BMA280 help Choose desired chip type from the BMA280 family. config BMA280_CHIP_BMA280 bool prompt "BMA280" help Choose this option to enable the BMA280 chip. config BMA280_CHIP_BMC150_ACCEL bool prompt "BMC150_ACCEL" help Choose this option to enable the accelerometer of the BMC150 chip. endchoice config BMA280_NAME string prompt "Driver name" default "BMA280" if BMA280_CHIP_BMA280 default "BMC150_ACCEL" if BMA280_CHIP_BMC150_ACCEL depends on BMA280 help Device name with which the sensor is identified. config BMA280_INIT_PRIORITY int prompt "Init priority" depends on BMA280 default 70 help Device driver initialization priority. choice prompt "I2C address" depends on BMA280 default BMA280_I2C_ADDR_0x18 if BMA280_CHIP_BMA280 default BMA280_I2C_ADDR_0x10 if BMA280_CHIP_BMC150_ACCEL help I2C address of the BMA280 sensor. config BMA280_I2C_ADDR_0x10 bool prompt "0x10" depends on BMA280_CHIP_BMC150_ACCEL help Choose this option if the SDO pin is pulled to GND. config BMA280_I2C_ADDR_0x11 bool prompt "0x11" depends on BMA280_CHIP_BMC150_ACCEL help Choose this option if the SDO pin is pulled to VDDIO. config BMA280_I2C_ADDR_0x18 bool prompt "0x18" depends on BMA280_CHIP_BMA280 help Choose this option if the SDO pin is pulled to GND. config BMA280_I2C_ADDR_0x19 bool prompt "0x19" depends on BMA280_CHIP_BMA280 help Choose this option if the SDO pin is pulled to VDDIO. endchoice config BMA280_I2C_MASTER_DEV_NAME string prompt "I2C master device name" depends on BMA280 default "I2C_0" help Specify the device name of the I2C master device to which chip is connected. choice prompt "Trigger mode" depends on BMA280 default BMA280_TRIGGER_GLOBAL_FIBER help Specify the type of triggering to be used by the driver. config BMA280_TRIGGER_NONE bool prompt "No trigger" config BMA280_TRIGGER_GLOBAL_FIBER bool prompt "Use global fiber" depends on GPIO select BMA280_TRIGGER select SENSOR_DELAYED_WORK config BMA280_TRIGGER_OWN_FIBER bool prompt "Use own fiber" depends on GPIO select BMA280_TRIGGER endchoice config BMA280_TRIGGER bool depends on BMA280 config BMA280_GPIO_DEV_NAME string prompt "GPIO device" default "GPIO_0" depends on BMA280 && BMA280_TRIGGER help The device name of the GPIO device to which the chip's interrupt pins are connected. config BMA280_GPIO_PIN_NUM int prompt "Interrupt GPIO pin number" default 0 depends on BMA280 && BMA280_TRIGGER help The number of the GPIO on which the interrupt signal from the chip will be received. config BMA280_FIBER_PRIORITY int prompt "Fiber priority" depends on BMA280 && BMA280_TRIGGER_OWN_FIBER default 10 help Priority of fiber used by the driver to handle interrupts. config BMA280_FIBER_STACK_SIZE int prompt "Fiber stack size" depends on BMA280 && BMA280_TRIGGER_OWN_FIBER default 1024 help Stack size of fiber used by the driver to handle interrupts. choice prompt "Acceleration measurement range" depends on BMA280 default BMA280_PMU_RANGE_2G help Measurement range for acceleration values. config BMA280_PMU_RANGE_2G bool prompt "+/-2g" config BMA280_PMU_RANGE_4G bool prompt "+/-4g" config BMA280_PMU_RANGE_8G bool prompt "+/-8g" config BMA280_PMU_RANGE_16G bool prompt "+/-16g" endchoice choice prompt "Acceleration data filter bandwidth" depends on BMA280 default BMA280_PMU_BW_7 help Bandwidth of filtered acceleration data. config BMA280_PMU_BW_1 bool prompt "7.81Hz" config BMA280_PMU_BW_2 bool prompt "15.63HZ" config BMA280_PMU_BW_3 bool prompt "31.25Hz" config BMA280_PMU_BW_4 bool prompt "62.5Hz" config BMA280_PMU_BW_5 bool prompt "125Hz" config BMA280_PMU_BW_6 bool prompt "250HZ" config BMA280_PMU_BW_7 bool prompt "500Hz" config BMA280_PMU_BW_8 bool prompt "unfiltered" endchoice