# Copyright (c) 2017 Intel Corporation # SPDX-License-Identifier: Apache-2.0 config SOC_ESP32 bool "ESP32" select XTENSA select CLOCK_CONTROL select DYNAMIC_INTERRUPTS select ARCH_HAS_GDBSTUB select ARCH_SUPPORTS_COREDUMP select PINCTRL select XIP select HAS_ESPRESSIF_HAL if SOC_ESP32 config IDF_TARGET_ESP32 bool "ESP32 as target board" default y config ESPTOOLPY_FLASHFREQ_80M bool default y config FLASH_SIZE int default $(dt_node_reg_size_int,/soc/flash-controller@3ff42000/flash@0,0) config FLASH_BASE_ADDRESS hex default $(dt_node_reg_addr_hex,/soc/flash-controller@3ff42000/flash@0) config ESP32_NETWORK_CORE bool "Uses the ESP32 APP_CPU as Network dedicated core" config ESP32_BT_RESERVE_DRAM hex "Bluetooth controller reserved RAM region" default 0xdb5c if BT default 0 config ESP_HEAP_MEM_POOL_REGION_1_SIZE int "Internal DRAM region 1 mempool size" default 1024 if ESP32_NETWORK_CORE default 49152 help ESP32 has two banks of size 192K and 128K which can be used as DRAM, system heap allocates area from region 0. This configuration can be used to add memory from region 1 to heap and can be allocated using k_malloc. config ESP_SPIRAM bool "Support for external, SPI-connected RAM" help This enables support for an external SPI RAM chip, connected in parallel with the main SPI flash chip. config ESP_HEAP_MIN_EXTRAM_THRESHOLD int "Minimum threshold for external RAM allocation" default 8192 range 1024 131072 depends on ESP_SPIRAM help Threshold to decide if memory will be allocated from DRAM or SPIRAM. If value of allocation size is less than this value, memory will be allocated from internal RAM. config ESP_HEAP_SEARCH_ALL_REGIONS bool "Search for all available heap regions" depends on ESP_SPIRAM default y help This configuration enables searching all available heap regions. If the region of desired capability is exhausted, memory will be allocated from other available region. menu "SPI RAM config" depends on ESP_SPIRAM choice SPIRAM_TYPE prompt "Type of SPI RAM chip in use" default SPIRAM_TYPE_ESPPSRAM16 config SPIRAM_TYPE_ESPPSRAM16 bool "ESP-PSRAM16 or APS1604" config SPIRAM_TYPE_ESPPSRAM32 bool "ESP-PSRAM32 or IS25WP032" config SPIRAM_TYPE_ESPPSRAM64 bool "ESP-PSRAM64 or LY68L6400" endchoice # SPIRAM_TYPE config ESP_SPIRAM_SIZE int "Size of SPIRAM part" default 2097152 if SPIRAM_TYPE_ESPPSRAM16 default 4194304 if SPIRAM_TYPE_ESPPSRAM32 default 8388608 if SPIRAM_TYPE_ESPPSRAM64 help Specify size of SPIRAM part. NOTE: If SPIRAM size is greater than 4MB, only lower 4MB can be allocated using k_malloc(). choice SPIRAM_SPEED prompt "Set RAM clock speed" default SPIRAM_SPEED_40M help Select the speed for the SPI RAM chip. If SPI RAM is enabled, we only support three combinations of SPI speed mode we supported now: 1. Flash SPI running at 40MHz and RAM SPI running at 40MHz 2. Flash SPI running at 80MHz and RAM SPI running at 40MHz 3. Flash SPI running at 80MHz and RAM SPI running at 80MHz Note: If the third mode(80MHz+80MHz) is enabled for SPI RAM of type 32MBit, one of the HSPI/VSPI host will be occupied by the system. Which SPI host to use can be selected by the config item SPIRAM_OCCUPY_SPI_HOST. Application code should never touch HSPI/VSPI hardware in this case. The option to select 80MHz will only be visible if the flash SPI speed is also 80MHz. (ESPTOOLPY_FLASHFREQ_79M is true) config SPIRAM_SPEED_40M bool "40MHz clock speed" config SPIRAM_SPEED_80M depends on ESPTOOLPY_FLASHFREQ_80M bool "80MHz clock speed" endchoice # SPIRAM_SPEED menu "PSRAM clock and cs IO for ESP32-DOWD" config D0WD_PSRAM_CLK_IO int "PSRAM CLK IO number" range 0 33 default 17 help The PSRAM CLOCK IO can be any unused GPIO, user can config it based on hardware design. If user use 1.8V flash and 1.8V psram, this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. config D0WD_PSRAM_CS_IO int "PSRAM CS IO number" range 0 33 default 16 help The PSRAM CS IO can be any unused GPIO, user can config it based on hardware design. If user use 1.8V flash and 1.8V psram, this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. endmenu # PSRAM clock and cs IO for ESP32-DOWD menu "PSRAM clock and cs IO for ESP32-D2WD" config D2WD_PSRAM_CLK_IO int "PSRAM CLK IO number" range 0 33 default 9 help User can config it based on hardware design. For ESP32-D2WD chip, the psram can only be 1.8V psram, so this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. config D2WD_PSRAM_CS_IO int "PSRAM CS IO number" range 0 33 default 10 help User can config it based on hardware design. For ESP32-D2WD chip, the psram can only be 1.8V psram, so this value can only be one of 6, 7, 8, 9, 10, 11, 16, 17. endmenu # PSRAM clock and cs IO for ESP32-D2WD menu "PSRAM clock and cs IO for ESP32-PICO" config PICO_PSRAM_CS_IO int "PSRAM CS IO number" range 0 33 default 10 help The PSRAM CS IO can be any unused GPIO, user can config it based on hardware design. For ESP32-PICO chip, the psram share clock with flash, so user do not need to configure the clock IO. For the reference hardware design, please refer to https://www.espressif.com/sites/default/files/documentation/esp32-pico-d4_datasheet_en.pdf endmenu # PSRAM clock and cs IO for ESP32-PICO config SPIRAM_CUSTOM_SPIWP_SD3_PIN bool "Use custom SPI PSRAM WP(SD3) Pin when flash pins set in eFuse (read help)" default y if SPIRAM_SPIWP_SD3_PIN != 7 # backwards compatibility, can remove in IDF 5 default n help This setting is only used if the SPI flash pins have been overridden by setting the eFuses SPI_PAD_CONFIG_xxx, and the SPI flash mode is DIO or DOUT. When this is the case, the eFuse config only defines 3 of the 4 Quad I/O data pins. The WP pin (aka ESP32 pin "SD_DATA_3" or SPI flash pin "IO2") is not specified in eFuse. The psram only has QPI mode, so a WP pin setting is necessary. If this config item is set to N (default), the correct WP pin will be automatically used for any Espressif chip or module with integrated flash. If a custom setting is needed, set this config item to Y and specify the GPIO number connected to the WP pin. When flash mode is set to QIO or QOUT, the PSRAM WP pin will be set the same as the SPI Flash WP pin configured in the bootloader. config SPIRAM_SPIWP_SD3_PIN int "Custom SPI PSRAM WP(SD3) Pin" range 0 33 default 7 help The option "Use custom SPI PSRAM WP(SD3) pin" must be set or this value is ignored If burning a customized set of SPI flash pins in eFuse and using DIO or DOUT mode for flash, set this value to the GPIO number of the SPIRAM WP pin. config SPIRAM bool default y endmenu # SPI RAM config choice ESP32_UNIVERSAL_MAC_ADDRESSES bool "Number of universally administered (by IEEE) MAC address" default ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR help Configure the number of universally administered (by IEEE) MAC addresses. During initialization, MAC addresses for each network interface are generated or derived from a single base MAC address. If the number of universal MAC addresses is four, all four interfaces (WiFi station, WiFi softap, Bluetooth and Ethernet) receive a universally administered MAC address. These are generated sequentially by adding 0, 1, 2 and 3 (respectively) to the final octet of the base MAC address. If the number of universal MAC addresses is two, only two interfaces (WiFi station and Bluetooth) receive a universally administered MAC address. These are generated sequentially by adding 0 and 1 (respectively) to the base MAC address. The remaining two interfaces (WiFi softap and Ethernet) receive local MAC addresses. These are derived from the universal WiFi station and Bluetooth MAC addresses, respectively. When using the default (Espressif-assigned) base MAC address, either setting can be used. When using a custom universal MAC address range, the correct setting will depend on the allocation of MAC addresses in this range (either 2 or 4 per device.) config ESP32_UNIVERSAL_MAC_ADDRESSES_TWO bool "Two" select ESP_MAC_ADDR_UNIVERSE_WIFI_STA select ESP_MAC_ADDR_UNIVERSE_BT config ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR bool "Four" select ESP_MAC_ADDR_UNIVERSE_WIFI_STA select ESP_MAC_ADDR_UNIVERSE_WIFI_AP select ESP_MAC_ADDR_UNIVERSE_BT select ESP_MAC_ADDR_UNIVERSE_ETH endchoice # ESP32_UNIVERSAL_MAC_ADDRESSES config ESP_MAC_ADDR_UNIVERSE_WIFI_AP bool config ESP_MAC_ADDR_UNIVERSE_WIFI_STA bool config ESP_MAC_ADDR_UNIVERSE_BT bool config ESP_MAC_ADDR_UNIVERSE_ETH bool config ESP32_UNIVERSAL_MAC_ADDRESSES int default 2 if ESP32_UNIVERSAL_MAC_ADDRESSES_TWO default 4 if ESP32_UNIVERSAL_MAC_ADDRESSES_FOUR config ESP32_PHY_MAX_WIFI_TX_POWER int "Max WiFi/BLE TX power (dBm)" range 10 20 default 20 help Set maximum transmit power for WiFi radio. Actual transmit power for high data rates may be lower than this setting. config ESP32_PHY_MAX_TX_POWER int default ESP32_PHY_MAX_WIFI_TX_POWER endif # SOC_ESP32