.. _atmel_at86rf2xx_transceivers: Atmel AT86RF2XX Transceivers ############################ Overview ******** The Atmel AT86RF2xx is a high performance radio transceiver targeted for IEEE 802.15.4, ZigBee, RF4CE, 6LoWPAN, and ISM applications. The AT86RF2xx is a true SPI-to-antenna solution and can be operated by any external microcontroller. The current IEEE 802.15.4 AT86RF2xx Zephyr driver currently works with any 2.4 Ghz transceiver, except AT86RF230. The RF2xx driver allows use of :ref:`ieee802154_interface` and :ref:`thread_protocol_interface` network stacks. This is a generic shield focused not only on Atmel Development Boards Kits. There are compatible designations for `AT AVR-RZ600`_ and `AT REB233-XPRO`_. This means, any Atmel board with 10-pin Xplained or 20-pin Xplained Pro extension headers can be used. You can check `Atmel Xplained Pro Hardware Development Kit User Guide`_ for more information. Besides that, Arduino and MikroBus standard headers are available to complement the shield module configurations. For any other project that doesn't fit on the current available variations an overlay can be created. However, the overlay is the last resource and is recommended use standard header always possible. RZ600 Module ============ The RZ600 Development Kit needs Atmel Xplained or Xplained-Pro header connector. The modules from this kit are available without any transceiver advanced features. For Xplained headers the `atmel_rf2xx_xplained`_ must be selected. For Xplained-Pro header the `atmel_rf2xx_legacy`_ must be enabled. .. image:: ./ATAVRRZ600.jpg :width: 350px :align: center :alt: AVR-RZ600 Pins Assignment of the RZ600 Module =================================== +---------+--------+-------------------------------------+ | Pin | Name | Function | +=========+========+=====================================+ | 1 | RST | GPIO - Reset | +---------+--------+-------------------------------------+ | 2 | MISC | DNU - Do Not Use | +---------+--------+-------------------------------------+ | 3 | IRQ | GPIO - Interrupt | +---------+--------+-------------------------------------+ | 4 | SLP_TR | GPIO - Multi purpose control signal | +---------+--------+-------------------------------------+ | 5 | CS | SPI Chip Select | +---------+--------+-------------------------------------+ | 6 | MOSI | SPI Master Out / Slave In | +---------+--------+-------------------------------------+ | 7 | MISO | SPI Master In / Slave Out | +---------+--------+-------------------------------------+ | 8 | SCLK | SPI Clock | +---------+--------+-------------------------------------+ | 9 | GND | | +---------+--------+-------------------------------------+ | 10 | VDD | POWER +3.3V | +---------+--------+-------------------------------------+ REB233-XPRO Module ================== The REB233-XPRO development kit uses Atmel Xplained Pro header. It is enabled selecting `atmel_rf2xx_xpro`_ option. .. image:: ./atreb233-xpro-top.jpg :width: 300px :align: center :alt: REB233-XPRO Top Pins Assignment of the REB233-XPRO Module ========================================= +---------+--------+-------------------------------------+ | Pin | Name | Function | +=========+========+=====================================+ | 1 | ID | DNU - Do Not Use | +---------+--------+-------------------------------------+ | 2 | GND | | +---------+--------+-------------------------------------+ | 3 | DIG1 | DNU - Do Not Use | +---------+--------+-------------------------------------+ | 4 | DIG3 | DNU - Do Not Use | +---------+--------+-------------------------------------+ | 5 | DIG2 | GPIO - RX Frame Time Stamping | +---------+--------+-------------------------------------+ | 6 | CLKM | DNU - Do Not Use | +---------+--------+-------------------------------------+ | 7 | RST | GPIO - Reset | +---------+--------+-------------------------------------+ | 8 | | | +---------+--------+-------------------------------------+ | 9 | IRQ | GPIO - Interrupt | +---------+--------+-------------------------------------+ | 10 | SLP_TR | GPIO - Multi purpose control signal | +---------+--------+-------------------------------------+ | 11 | SDA | EEPROM - AT24MAC602 | +---------+--------+-------------------------------------+ | 12 | SCL | EEPROM - AT24MAC602 | +---------+--------+-------------------------------------+ | 13 | | | +---------+--------+-------------------------------------+ | 14 | | | +---------+--------+-------------------------------------+ | 15 | CS | SPI Chip Select | +---------+--------+-------------------------------------+ | 16 | MOSI | SPI Master Out / Slave In | +---------+--------+-------------------------------------+ | 17 | MISO | SPI Master In / Slave Out | +---------+--------+-------------------------------------+ | 18 | SCLK | SPI Clock | +---------+--------+-------------------------------------+ | 19 | GND | | +---------+--------+-------------------------------------+ | 20 | VDD | POWER +3.3V | +---------+--------+-------------------------------------+ .. note:: DIG2 is not current implemented on RF2xx driver. Arduino Shields =============== Arduino Uno R3 header is available without advanced features. It is enabled selecting `atmel_rf2xx_arduino`_ variante option. Pins Assignment of the Arduino Shield Modules ============================================= +---------+--------+-------------------------------------+ | Pin | Name | Function | +=========+========+=====================================+ | D0 | | | +---------+--------+-------------------------------------+ | D1 | | | +---------+--------+-------------------------------------+ | D2 | IRQ | GPIO - Interrupt | +---------+--------+-------------------------------------+ | D3 | | | +---------+--------+-------------------------------------+ | D4 | | | +---------+--------+-------------------------------------+ | D5 | | | +---------+--------+-------------------------------------+ | D6 | | | +---------+--------+-------------------------------------+ | D7 | | | +---------+--------+-------------------------------------+ | D8 | RST | GPIO - Reset | +---------+--------+-------------------------------------+ | D9 | SLP_TR | GPIO - Multi purpose control signal | +---------+--------+-------------------------------------+ | D10 | CS | SPI Chip Select | +---------+--------+-------------------------------------+ | D11 | MOSI | SPI Master Out / Slave In | +---------+--------+-------------------------------------+ | D12 | MISO | SPI Master In / Slave Out | +---------+--------+-------------------------------------+ | D13 | SCLK | SPI Clock | +---------+--------+-------------------------------------+ | D14 | | | +---------+--------+-------------------------------------+ | D15 | | | +---------+--------+-------------------------------------+ | | GND | | +---------+--------+-------------------------------------+ | | VDD | POWER +3.3V | +---------+--------+-------------------------------------+ | | VCC | POWER +5.0V | +---------+--------+-------------------------------------+ MikroBus Shields ================ MikroBus header is available available without advanced features. It is enabled selecting `atmel_rf2xx_mikrobus`_ variante option. Pins Assignment of the MikroBus Shield Modules ============================================== +---------+--------+-------------------------------------+ | Pin | Name | Function | +=========+========+=====================================+ | AN | RST | GPIO - Reset | +---------+--------+-------------------------------------+ | RST | | | +---------+--------+-------------------------------------+ | CS | CS | SPI Chip Select | +---------+--------+-------------------------------------+ | SCK | SCLK | SPI Clock | +---------+--------+-------------------------------------+ | MISO | MISO | SPI Master In / Slave Out | +---------+--------+-------------------------------------+ | MOSI | MOSI | SPI Master Out / Slave In | +---------+--------+-------------------------------------+ | VCC-3.3 | VDD | POWER +3.3V | +---------+--------+-------------------------------------+ | GND | GND | | +---------+--------+-------------------------------------+ | GND | GND | | +---------+--------+-------------------------------------+ | VCC-5.0 | VCC | POWER +5.0V | +---------+--------+-------------------------------------+ | SDA | | | +---------+--------+-------------------------------------+ | SCL | | | +---------+--------+-------------------------------------+ | TX | | | +---------+--------+-------------------------------------+ | RX | | | +---------+--------+-------------------------------------+ | INT | IRQ | GPIO - Interrupt | +---------+--------+-------------------------------------+ | PWM | SLP_TR | GPIO - Multi purpose control signal | +---------+--------+-------------------------------------+ Supported variations ==================== The below table suggests shield variation accordingly with end user application. When a standard connector (arduino, mikrobus, xplained, xplained-pro) is available on board, user should select the matching shield configuration. When atmel_rf2xx shield is used with a board that doesn't feature a standard connector, a dedicated .overlay file should be provided. The remaining configurations should be used based on the board standard headers available. +-----------------------------+------------------------------+-----------+ | Connector Standard | Shield Designation | Variation | +=============================+==============================+===========+ | Without standard (overlay) | `atmel_rf2xx`_ | 1 | +-----------------------------+------------------------------+-----------+ | Atmel Xplained header | `atmel_rf2xx_xplained`_ | 2 | +-----------------------------+------------------------------+-----------+ | Atmel Xplained Pro header | `atmel_rf2xx_xpro`_ | 3 | +-----------------------------+------------------------------+-----------+ | Atmel Xplained Pro header | `atmel_rf2xx_legacy`_ | 4 | +-----------------------------+------------------------------+-----------+ | Arduino | `atmel_rf2xx_arduino`_ | 5 | +-----------------------------+------------------------------+-----------+ | MikroBus | `atmel_rf2xx_mikrobus`_ | 6 | +-----------------------------+------------------------------+-----------+ Requirements ************ This shield requires a board which provides a configuration that allows an SPI interface, an interrupt signal and two GPIO. (see :ref:`shields` for more details). .. note:: Boards that already have a network interface: Check network documentation to understand how properly configure both interfaces. To keep simple, make sure IEEE 802.15.4 is the only interface enabled at Networking -> Link Layer Options. This will avoid problems running Zephyr samples. Tested Boards ============= +-----------------------------+------------------------------+-----------+ | Board | Disabled Interface | Variation | +=============================+==============================+===========+ | ATMEL sam4s_xplained | | 2 | +-----------------------------+------------------------------+-----------+ | ATMEL sam4e_xpro | Ethernet | 3 , 4 | +-----------------------------+------------------------------+-----------+ | ATMEL sam_v71_xult | Ethernet | 3 , 4 , 5 | +-----------------------------+------------------------------+-----------+ Sample usage ************ You can try use IEEE 802.15.4 and/or OpenThread with the Zephyr Echo server and Echo client samples, which provide out-of-the-box configuration for both IEEE 802.15.4 and OpenThread. To enable IEEE 802.15.4 support in the samples, build them with ``overlay-802154.conf`` overlay config file. Same way, to enable OpenThread support, build them with ``overlay-ot.conf`` overlay config file. See :ref:`sockets-echo-server-sample` and :ref:`sockets-echo-client-sample` for details. Build and Programming ********************* Set ``-DSHIELD=`` when you invoke ``west build``. .. zephyr-app-commands:: :zephyr-app: samples/net/sockets/echo_server :host-os: unix :board: sam4s_xplained :gen-args: -DOVERLAY_CONFIG=overlay-802154.conf :shield: atmel_rf2xx_xplained :goals: build flash :compact: .. zephyr-app-commands:: :zephyr-app: samples/net/sockets/echo_server :host-os: unix :board: [sam4e_xpro | sam_v71_xult] :gen-args: -DOVERLAY_CONFIG=overlay-802154.conf :shield: [atmel_rf2xx_xpro | atmel_rf2xx_legacy] :goals: build flash :compact: .. zephyr-app-commands:: :zephyr-app: samples/net/sockets/echo_server :host-os: unix :board: [sam_v71_xult | frdm_k64f | nucleo_f767zi] :gen-args: -DOVERLAY_CONFIG=overlay-802154.conf :shield: atmel_rf2xx_arduino :goals: build flash :compact: .. zephyr-app-commands:: :zephyr-app: samples/net/sockets/echo_server :host-os: unix :board: lpcxpresso55s69_ns :gen-args: -DOVERLAY_CONFIG=overlay-802154.conf :shield: atmel_rf2xx_microbus :goals: build flash :compact: References ********** .. target-notes:: .. _AT AVR-RZ600: https://www.microchip.com/DevelopmentTools/ProductDetails/PartNO/ATAVRRZ600 .. _AT REB233-XPRO: https://www.microchip.com/DevelopmentTools/ProductDetails/PartNO/ATREB233-XPRO .. _Atmel Xplained Pro Hardware Development Kit User Guide: http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-42091-Atmel-Xplained-Pro-Hardware-Development-Kit_User%20Guide.pdf .. _atmel_rf2xx: https://github.com/zephyrproject-rtos/zephyr/blob/master/boards/shields/atmel_rf2xx/atmel_rf2xx.overlay .. _atmel_rf2xx_xplained: https://github.com/zephyrproject-rtos/zephyr/blob/master/boards/shields/atmel_rf2xx/atmel_rf2xx_xplained.overlay .. _atmel_rf2xx_xpro: https://github.com/zephyrproject-rtos/zephyr/blob/master/boards/shields/atmel_rf2xx/atmel_rf2xx_xpro.overlay .. _atmel_rf2xx_legacy: https://github.com/zephyrproject-rtos/zephyr/blob/master/boards/shields/atmel_rf2xx/atmel_rf2xx_legacy.overlay .. _atmel_rf2xx_arduino: https://github.com/zephyrproject-rtos/zephyr/blob/master/boards/shields/atmel_rf2xx/atmel_rf2xx_arduino.overlay .. _atmel_rf2xx_mikrobus: https://github.com/zephyrproject-rtos/zephyr/blob/master/boards/shields/atmel_rf2xx/atmel_rf2xx_mikrobus.overlay