#
# Copyright (c) 2018 Intel Corporation
#
# SPDX-License-Identifier: Apache-2.0
#

menuconfig I2C_QMSI
	bool "QMSI I2C driver"
	depends on QMSI
	default n
	help
	  This option enable the QMSI I2C driver.

	  This driver is simply a shim driver based on the I2C driver
	  provided by the QMSI BSP.

if I2C_QMSI

config I2C_SDA_SETUP
	int
	help
	  The delay time of clock rising edge relative to i2c data signal
	  change. The unit is i2c module base clock.

config I2C_SDA_TX_HOLD
	int
	help
	  The hold time on the data signal after a negative edge of i2c clock
	  while i2c acts as transmitter. The unit is i2c module base clock.

config I2C_SDA_RX_HOLD
	int
	help
	  The hold time on the data signal after a negative edge of i2c clock
	  while i2c acts as receiver. The unit is i2c module base clock.

endif # I2C_QMSI


menuconfig I2C_QMSI_SS
	bool "QMSI I2C driver for the Sensor Subsystem"
	depends on QMSI
	default n
	help
	  This option enable the Sensor QMSI I2C driver.

	  This driver is simply a shim driver based on the I2C driver
	  provided by the QMSI BSP.

if I2C_QMSI_SS

config I2C_SS_0
	bool "Enable I2C_SS_0"
	default n

config I2C_SS_0_NAME
	string "Select a name for finding the device"
	depends on I2C_SS_0 && !HAS_DTS_I2C
	default "I2C_SS_0"

config I2C_SS_0_BITRATE
	hex "I2C SS 0 default bitrate"
	depends on I2C_SS_0 && !HAS_DTS_I2C
	default 0x0
	help
	  Allows the I2C port to be brought up with a default configuration.
	  This is useful to set if other drivers depend upon using the I2C bus
	  before the application has a chance to custom configure the port.
	  Setting this value does not prohibit the application from customizing
	  the values later.  Refer to the I2C datasheet for proper values.

config I2C_SS_1
	bool "Enable I2C SS Port 1"
	default n

config I2C_SS_1_NAME
	string "Select a name for finding the device"
	depends on I2C_SS_1 && !HAS_DTS_I2C
	default "I2C_SS_1"

config I2C_SS_1_BITRATE
	hex "I2C SS 1 default bitrate"
	depends on I2C_SS_1 && !HAS_DTS_I2C
	default 0x0
	help
	  Allows the I2C port to be brought up with a default configuration.
	  This is useful to set if other drivers depend upon using the I2C bus
	  before the application has a chance to custom configure the port.
	  Setting this value does not prohibit the application from customizing
	  the values later.  Refer to the I2C datasheet for proper values.

config I2C_SS_SDA_HOLD
	int
	help
	  The hold time on the data signal after a negative edge of i2c clock.
	  The unit is i2c module base clock.

config I2C_SS_SDA_SETUP
	int
	help
	  The delay time of clock rising edge relative to i2c data signal
	  change. The unit is i2c module base clock.

endif # I2C_QMSI_SS