.. _frdm_kw41z: NXP FRDM-KW41Z ############## Overview ******** The FRDM-KW41Z is a development kit enabled by the Kinetis |reg| W series KW41Z/31Z/21Z (KW41Z) family built on ARM |reg| Cortex |reg|-M0+ processor with integrated 2.4 GHz transceiver supporting Bluetooth |reg| Smart/Bluetooth |reg| Low Energy (BLE) v4.2, Generic FSK, IEEE |reg| 802.15.4 and Thread. The FRDM-KW41Z kit contains two Freedom boards that can be used as a development board or a shield to connect to a host processor. The FRDM-KW41Z is form-factor compatible with the Arduino |trade| R3 pin layout for more expansion options. The FRDM-KW41Z highly-sensitive, optimized 2.4 GHz radio features a PCB F-antenna which can be bypassed to test via SMA connection, multiple power supply options, push/capacitive touch buttons, switches, LEDs and integrated sensors. .. image:: ./frdm_kw41z.jpg :width: 720px :align: center :alt: FRDM-KW41Z Hardware ******** - Can be configured as Host or Shield for connection to Host Processor - Supports all DC-DC configurations (Buck, Boost, Bypass) - PCB inverted F-type antenna - SMA RF Connector - RF regulatory certified - Serial Flash for OTA firmware upgrades - On board NXP FXOS8700CQ digital sensor, 3D Accelerometer ( |plusminus| 2g/ |plusminus| 4g/ |plusminus| 8g) + 3D Magnetometer - OpenSDA and JTAG debug For more information about the KW41Z SoC and FRDM-KW41Z board: - `KW41Z Website`_ - `KW41Z Datasheet`_ - `KW41Z Reference Manual`_ - `FRDM-KW41Z Website`_ - `FRDM-KW41Z User Guide`_ - `FRDM-KW41Z Schematics`_ Supported Features ================== The frdm_kw41z board configuration supports the following hardware features: +-----------+------------+-------------------------------------+ | Interface | Controller | Driver/Component | +===========+============+=====================================+ | NVIC | on-chip | nested vector interrupt controller | +-----------+------------+-------------------------------------+ | SYSTICK | on-chip | systick | +-----------+------------+-------------------------------------+ | PINMUX | on-chip | pinmux | +-----------+------------+-------------------------------------+ | COUNTER | on-chip | rtc | +-----------+------------+-------------------------------------+ | GPIO | on-chip | gpio | +-----------+------------+-------------------------------------+ | I2C | on-chip | i2c | +-----------+------------+-------------------------------------+ | SPI | on-chip | spi | +-----------+------------+-------------------------------------+ | ADC | on-chip | adc | +-----------+------------+-------------------------------------+ | UART | on-chip | serial port-polling; | | | | serial port-interrupt | +-----------+------------+-------------------------------------+ | FLASH | on-chip | soc flash | +-----------+------------+-------------------------------------+ | SENSOR | off-chip | fxos8700 polling: | | | | fxos8700 trigger | +-----------+------------+-------------------------------------+ | PWM | on-chip | tpm | +--------------------------------------------------------------+ The default configuration can be found in the defconfig file: ``boards/arm/frdm_kw41z/frdm_kw41z_defconfig`` Other hardware features are not currently supported by the port. Connections and IOs =================== The KW41Z SoC has three pairs of pinmux/gpio controllers, but only two are currently enabled (PORTA/GPIOA and PORTC/GPIOC) for the FRDM-KW41Z board. +-------+-------------+---------------------------+ | Name | Function | Usage | +=======+=============+===========================+ | PTC1 | GPIO | Red LED / FXOS8700 INT1 | +-------+-------------+---------------------------+ | PTA19 | GPIO | Green LED | +-------+-------------+---------------------------+ | PTA18 | GPIO | Blue LED | +-------+-------------+---------------------------+ | PTB2 | ADC | ADC0 channel 3 | +-------+-------------+---------------------------+ | PTC2 | I2C1_SCL | I2C / FXOS8700 | +-------+-------------+---------------------------+ | PTC3 | I2C1_SDA | I2C / FXOS8700 | +-------+-------------+---------------------------+ | PTC4 | GPIO | SW3 | +-------+-------------+---------------------------+ | PTC5 | GPIO | SW4 | +-------+-------------+---------------------------+ | PTC6 | LPUART0_RX | UART Console | +-------+-------------+---------------------------+ | PTC7 | LPUART0_TX | UART Console | +-------+-------------+---------------------------+ | PTC16 | SPI0_SCK | SPI | +-------+-------------+---------------------------+ | PTC17 | SPI0_SOUT | SPI | +-------+-------------+---------------------------+ | PTC18 | SPI0_SIN | SPI | +-------+-------------+---------------------------+ | PTC19 | SPI0_PCS0 | SPI | +-------+-------------+---------------------------+ System Clock ============ The KW41Z SoC is configured to use the 32 MHz external oscillator on the board with the on-chip FLL to generate a 40 MHz system clock. Serial Port =========== The KW41Z SoC has one UART, which is used for the console. Programming and Debugging ************************* Build and flash applications as usual (see :ref:`build_an_application` and :ref:`application_run` for more details). Configuring a Debug Probe ========================= A debug probe is used for both flashing and debugging the board. This board is configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`. Option 1: :ref:`opensda-daplink-onboard-debug-probe` (Recommended) ------------------------------------------------------------------ Install the :ref:`pyocd-debug-host-tools` and make sure they are in your search path. Follow the instructions in :ref:`opensda-daplink-onboard-debug-probe` to program the `OpenSDA DAPLink FRDM-KW41Z Firmware`_. Option 2: :ref:`opensda-jlink-onboard-debug-probe` -------------------------------------------------- Install the :ref:`jlink-debug-host-tools` and make sure they are in your search path. Follow the instructions in :ref:`opensda-jlink-onboard-debug-probe` to program the `OpenSDA J-Link FRDM-KW41Z Firmware`_. Add the argument ``-DOPENSDA_FW=jlink`` when you invoke ``west build`` to override the default runner from pyOCD to J-Link: .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: frdm_kw41z :gen-args: -DOPENSDA_FW=jlink :goals: build Configuring a Console ===================== Regardless of your choice in debug probe, we will use the OpenSDA microcontroller as a usb-to-serial adapter for the serial console. Connect a USB cable from your PC to J6. Use the following settings with your serial terminal of choice (minicom, putty, etc.): - Speed: 115200 - Data: 8 bits - Parity: None - Stop bits: 1 Flashing ======== Here is an example for the :ref:`hello_world` application. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: frdm_kw41z :goals: flash Open a serial terminal, reset the board (press the SW1 button), and you should see the following message in the terminal: .. code-block:: console ***** Booting Zephyr OS v1.14.0-rc1 ***** Hello World! frdm_kw41z Debugging ========= Here is an example for the :ref:`hello_world` application. .. zephyr-app-commands:: :zephyr-app: samples/hello_world :board: frdm_kw41z :goals: debug Open a serial terminal, step through the application in your debugger, and you should see the following message in the terminal: .. code-block:: console ***** Booting Zephyr OS v1.14.0-rc1 ***** Hello World! frdm_kw41z .. _FRDM-KW41Z Website: https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/kinetis-cortex-m-mcus/w-serieswireless-conn.m0-plus-m4/freedom-development-kit-for-kinetis-kw41z-31z-21z-mcus:FRDM-KW41Z .. _FRDM-KW41Z User Guide: https://www.nxp.com/webapp/Download?colCode=FRDMKW41ZUG .. _FRDM-KW41Z Schematics: https://www.nxp.com/webapp/Download?colCode=FRDM-KW41Z-SCH .. _KW41Z Website: https://www.nxp.com/products/wireless/zigbee/kinetis-kw41z-2.4-ghz-dual-mode-bluetooth-low-energy-and-802.15.4-wireless-radio-microcontroller-mcu-based-on-arm-cortex-m0-plus-core:KW41Z .. _KW41Z Datasheet: https://www.nxp.com/docs/en/data-sheet/MKW41Z512.pdf .. _KW41Z Reference Manual: https://www.nxp.com/webapp/Download?colCode=MKW41Z512RM .. _OpenSDA DAPLink FRDM-KW41Z Firmware: https://www.nxp.com/assets/downloads/data/en/reference-applications/OpenSDAv2.2_DAPLink_frdmkw41z_rev0241.zip .. _OpenSDA J-Link FRDM-KW41Z Firmware: https://www.segger.com/downloads/jlink/OpenSDA_FRDM-KW41Z