To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_SAME70*
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The RTC node for some reason was setting #address-cells and #size-cells.
However it has no children so there isn't really any reason to do this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In case of out of tree SoC, mem.h will trigger and error since
it is not aware of new SoC CONFIG_SOC_<reference>.
Modify error condition in order to generate the error only if
the flash and error size are not defined at this point (even in
out of tree case).
Fixes#9978
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_EFM32WG990F256
CONFIG_SOC_PART_NUMBER_EFR32FG1P133F256GM48
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_CC3220SF
CONFIG_SOC_MSP432P401R
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add 'generation: define' directive to 'compatible' property.
When existing for a type of device, move compatible property
description in device base structure (eg: i2c.yaml)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
All flash controllers have a mandatory compatible property.
Add it to the generic binding that is included by all.
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the sample under samples/boards/nrf52/power_mgr.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
According to Device Tree specification, previously
defined nodes may be deleted with the followin
syntax:
/delete-node/ node-name;
or
/delete-node/ &label;
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
This commit adds ADC nodes to DTS files for nRF SoCs and introduces
corresponding bindings for these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The whole STM32L4 family has a flash with a constant page size of 2kB.
Specify this value in the DTS as the nvs sample application pull it
from there.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The nvs sample assumed a 1 KB flash erase block size, which caused the
sample to fail on frdm_k64f because its erase block size is 4 KB. Get
the erase block size from dts instead.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for TI LP5562 I2C 4-channel LED driver.
Supported blinking period: 1ms - 1000ms
Supported brightness value: 0% - 100%
This driver supports the entire currently available API.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Add support for usbotg_fs, by adding the DT fixup, pinmux macros,
and the DT entries in stm32f2.dtsi.
Signed-off-by: Istvan Bisz <istvan.bisz@t-online.hu>
The L433 chip is a superset of the L432, just grabbing a few additional
interfaces (LCD, I2C2, USART3, SPI2, SDMMC). All the support/HAL files
are already there, so enabling these is just a matter of build system
setup.
Tested on an application specific board (builds correctly and I2C2
works.) I unfortunately don't have a nucleo/discovery board to create a
reference board for.
Signed-off-by: David Lamparter <equinox@diac24.net>
This patch adds the RDC (Resource Domain Controller) peripheral
permissions settings for the i.MX applications cores (Cortex A9 on
i.MX6 and Cortex A7 on i.MX7).
This will enable both Linux (on application's core) and Zephyr (on M4
core) to share the peripherals and coexist.
The settings are defined at devicetree level and applied in the soc.c.
A complete solution should involve the SEMA4 to control the peripherals
access and prevent resource deadlocking and misusage.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
The WNC-M14A2A (LTE / LTE-M) modem is presented as an Arduino-
compatible shield via AT&T's IoT Starter Kit v1.0. It was
originally intended to work with the FRDM-K64F board, but
in theory as long as the right pins are configured it can
work with any board that supports Arduino-compatible headers.
The driver utilizes the CONFIG_NET_OFFLOAD setting to avoid the
normal handling of IP packets, and instead uses a socket-like
UART interface to handle incoming and outgoing data.
Signed-off-by: Michael Scott <mike@foundries.io>
Only basic features supported initially but more could be added from:
https://www.nxp.com/docs/en/data-sheet/MMA8451Q.pdffixes#9006
A sample app will be provided in a separate PR.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
The STM32F7 uses the V2 version of the STM32 I2C controller. Add the
corresponding Kconfig, DTS, DTS fixup and pinmux entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This adds the SoC configuration for Apollo Lake. This is based
on the Atom configuration.
Origin: Original
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
After running some tests which enable assert macro I found some issues
with the i.MX UART configuration.
This patch configures the Tx Fifo Watermark and Modem Mode accordingly.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
The common spi.yaml defines an optional clocks property that can be
overridden by specific spi driver bindings to be required. The
description and generation attributes are duplicated.
This fixes build warnings:
extract_dts_includes.py: Merge of 'description': 'Clock gate control
information' overwrites 'Clock gate information'.
extract_dts_includes.py: Merge of 'generation': 'structures' overwrites
'define'.
And introduces a different build warning, which is intended behavior:
extract_dts_includes.py: Merge of 'category': 'required' overwrites
'optional'.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The common uart.yaml defines an optional clocks property that can be
overridden by specific serial driver bindings to be required. The
description and generation attributes are duplicated.
This fixes build warnings:
extract_dts_includes.py: Merge of 'description': 'Clock gate control
information' overwrites 'Clock gate information'.
extract_dts_includes.py: Merge of 'generation': 'structures' overwrites
'define'.
And introduces a different build warning, which is intended behavior:
extract_dts_includes.py: Merge of 'category': 'required' overwrites
'optional'.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Kumar Gala