Log the address and the err/reason values in the connected
and disconnect callbacks.
Since these values are not part of the BTP events it is
difficult to follow the order and reason why disconnects
happen when debugging.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add conversion macros from milliseconds to various units.
The purpose of these macros is to make it more clear/easier
for users to set and read values using milliseconds rather
than the various BT units which may be in 0.625, 1.25 or 10ms
units.
This is especially useful when comparing related values using
different units, such as advertising interval (0.625ms units)
and periodic advertising interval units (1.25ms units).
Users will have to be aware that these macros can provide slightly
different values than what is provided, if the provided values
do not match the units.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Fix compilation error by specifying usart1 to be used for uart-pipe.
Add a board-specific configuration file to disable the console,
so, the usart1 will be used only for bluetooth and to specify
the BT_HCI_TX_STACK_SIZE.
Signed-off-by: Nidhal BEN OTHMEN <nidhal.benothmen@st.com>
Workaround failing autopts weekly run due to tester
application having Bus Fault in the nRF53 NET core hci_ipc
firmware at startup.
Having atleast 32 bytes free in nRF53x hci_ipc sample to
avoid Bus Fault when Zephyr Kernel does SYSINIT calls.
Reduce supported ISO Broadcaster instance and ISO TX buffer
counts in the Controller hci_ipc firmware.
Add sysbuild support for tester application so that the
build is CI verified.
sysbuild commandline for LE audio PTS testing:
# west build --sysbuild -b nrf5340_audio_dk/nrf5340/cpuapp
-d build/tester tests/bluetooth/tester
-DEXTRA_CONF_FILE="overlay-le-audio.conf"
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The CAP tests used u_group->cig->index but the u_group->cig may
have been deleted when the stream is released, which meant
that u_group->cig == NULL when e.g. unicast_stop_complete_cb
was called and that could cause failing tests as the index
would just be a uninitialized value.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add log statements for each command, event and response
for debugging purposes.
Tests do not send enough of these to clutter the IUT logs
and it is useful for debugging to more easily determine
what command triggered a function call or when the
responses and events are sent to the AutoPTS client.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Removed the LE Audio specific definition and instead
refer to the value defined by iso.h as it is ISO/Core
that defines this size, and not BAP/Audio.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Removed the generation of broadcast id inside the stack. It is now up
to the application to generate this by itself. The CAP sample has
been modified to allow either a static broadcast, or a random one.
All of this is handled in the application.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
Changed dependency of the BT_BAP_SCAN_DELEGATOR to GATT_DYNAMIC_DB
from 'select' to 'depends on' and solved all loop dependencies
caused by this change.
Fixes#79108
Signed-off-by: Babak Arisian <bbaa@demant.com>
Add support for building and running the BT tester on the
nrf5340_audio_dk.
This is copying the configuration used for the nRF5340 DK.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This makes sure we always fit all configurations. Worst case is two
audio streams in 48_6 configuration in single ISO channel (2x155).
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
For now this seems to be required by PTS as there is not Upper Tester
action for this in Test Specification.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Modify the GAP connect to use 30ms. The default parameters
typically ended up with 50ms which is OK in most cases,
but for ISO related test cases, using an ACL interval that
is a multiple of the ISO SDU interval (7.5/10ms) generally
provides better stability. 30ms is the lowest multiple
of both 7.5 and 10ms, and was thus chosen.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
If the Broadcast ID is initially set to 0x000000,
which is valid, comparison logic on add of an
actual Broadcast ID of 0x000000 fails.
Likewise for SID.
Moving INVALID_BROADCAST_ID define to bap.h
Signed-off-by: Lars Knudsen <LAKD@demant.com>
The host-based adv auto-resume function has both a problematic
implementation and disagreement in the community around how it should
behave. See the issue linked resolved below for details.
This patch makes the deprecation visible to the user. The user will be
better served by a auto-resume tailored their applications use case,
based on more primitive host API like `conn_cb.recycled`, which has
obvious behavior that is unlikely to change.
Resolves: https://github.com/zephyrproject-rtos/zephyr/issues/72567
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Adds a semaphor to make sure the stream has properly been stopped by the
controller before returning from btp_bap_broadcast_source_stop.
Signed-off-by: Frode van der Meeren <frode.vandermeeren@nordicsemi.no>
The QoS structure is not related to a codec, but rather a
stream, and should thus not use the "Codec" name.
The BAP and ASCS specs refer to the QoS as
"QoS configuration" several places, so it is an obvious
choice for a name.
Since the structure is defined and used by BAP, the prefix
was changed from bt_audio to bt_bap.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
TBS registration was changed from static to dynamic
and the BT Tester application need to be updated to use
the dynamic registration.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Adds the `bt_mesh_brg_cfg` prefix to the public Subnet Bridge API, and
aligns the function and callback naming with the rest of the Bluetooth
Mesh API.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
The unicast_stop function is changed to primarily do a
BAP disable instead of a release, with optional
support for releasing the streams once they have been disabled.
This also adds unittests for the procedure which also
allow us to remove the invalid param testing from the BSIM tests.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Increasing the number of max tx segments to be able to fit composition
page 0 into composition data status message.
After the subnet bridge config client and server are added to the
tester, the size needed to report composition data page 0 increased.
Current behaviour of the tester is correct, dropping the element when
there is not enough space in data field, however the PTS application
does not handle the composition data status message without element.
Signed-off-by: alperen sener <alperen.sener@nordicsemi.no>
Added support for dynamic registration and unregistration of the
Broadcast Audio Scan Service (BASS) within the scan delegator.
This enables both scan delegator and BASS to be registered or
unregistered dynamically at runtime.
Signed-off-by: Babak Arisian <bbaa@demant.com>
native_posix is now deprecated.
Building these tests in both native_sim and native_posix does not
improve coverage for the tests or subsystem but doubles CI time.
As anyhow native_posix will be removed all together in
2 releases, let's remove it already for these.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
BAP mandates support for bondable mode for all central and
peripheral roles.
Due to Kconfig circular dependencies, some additional
Kconfig changes had to be made.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Rename the volume flag field from the generic "flags"
to "vol_flags" as the generic "flags" will be used for
other values in a future commit.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Removed deprecated native_posix as test platform.
Added unique sim_ids for tests with the psa as a overlay.
Fixed clang-format issues.
Signed-off-by: Ingar Kulbrandstad <ingar.kulbrandstad@nordicsemi.no>
When a synchronous API is used, the content of `buf` will not be
valid by the time the thread that called the synchronous API is woken up
again.
Therefore, the simplest way to solve this is when a user allocates the
buffer which will be filled up with the content of the buffer passed to
the model callback.
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
Added support for the Bridge Configuration client and server
to the tester application.
Signed-off-by: Ingar Kulbrandstad <ingar.kulbrandstad@nordicsemi.no>
Any places that checked for GTBS is now always enabled
as GTBS is mandatory to support, and the Kconfig option
was removed.
Also removed a duplicate Kconfig option for TBS,
BT_TBS_SERVICE_COUNT, as it was unused.
The other Kconfig option BT_TBS_BEARER_COUNT is used
instead exclusively to set it if needed.
Since GTBS can now exist alone, it must also
support having its own calls and other values.
This means that the GTBS and TBS instances now share
the same underlying struct.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Added option to set the ASE count through the bap API, making ASE
configuration runtime available. The upper limit of ASEs are still
bound by the Kconfig options set for ASEs.
Signed-off-by: Fredrik Danebjer <frdn@demant.com>
Move the network buffer header file from zephyr/net/buf.h to
zephyr/net_buf.h as the implementation now lives outside of the networking
subsystem.
Add (deprecated) zephyr/net/buf.h header to maintain compatibility with old
file path.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The TBS client callbacks are just informative so we
provide the information to multiple listeners.
To support this for the long strings, the function
handle_string_long_read was refactored.
This also allows for multiple users of the TBS client.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Since testing.c/h was moved to mesh, all functions and
structs in those files now follow a bt_mesh_test_*
naming scheme to be consistent with the naming in Zephyr.
Due to missing includes in many files, this commit also
added some that were missing in order to build since
the order of includes have changed.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The file is only ever used by mesh and it is even stated in the
header of the file that it is internal APIs.
The include file has been merged with the host testing.h file
as that was mesh specific as well. Similarly the testing.c
file was also moved
This is part of a process to clean up the file structure of
Bluetooth as it's a bit messy, which is evident from the
MAINTAINERS.yml file.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
There was hardcoded value for user_data which is no longer valid.
Use proper CONFIG_BT_CONN_TX_USER_DATA_SIZE for that.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Add conn parameter to status/flags callbacks of bt_vcp_vol_rend_cb
to differentiate between remote and local changes.
Signed-off-by: Chang An <chang.an_1@nxp.com>
[Description]
Device hang is observed when LE Scan
[Root Cause]
For le_ext_adv_report, Data[i] of one adv report is 0-229,
for the adv_buf of saving, it just is 73 bytes, so sometimes
the bytes of adv report is more than the adv_buf, resulted hang
[Fix]
consider the le ext adv case.
[Testing]
After modified, Device hang is not observed after stress
testing with LE Scan
Signed-off-by: Guotao Zhang <guotao.zhang@nxp.com>
Zero length arrays are only allowed at the end of the structure. Here
those were used as placeholders for BTP response creation and can be
easily replaced with common member.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Refactors teh BIS bitfield values used for ISO
and BAP.
Previously BIT(1) meant BIS index 1, which was a Zephyr choice
in the early days of ISO, as the BT Core spec did not use
a bitfield for BIS indexes.
Later the BASS specification came along and defined that
BIT(0) meant BIS index 1, which meant that we had to shift BIS
bitfields between BAP and ISO.
This commit refactors the ISO layer to use BIT(0) for Index 1 now,
which means that there is no longer a need for conversion
between the BAP and ISO layers, and that we can use a value
range defined by a BT Core spec (BASS).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The bug should be fixed now, so it possible to have it enabled as
long as OTS is not registered with the feature flag.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The macro was changed to return a const pointer, but the
BTP use the returned pointer in a non-const way.
Modify the usage so that the macro is used to initialize
the adv_param instead, and then provide a non-const pointer
to tester_gap_create_adv_instance.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Emil Gydesen