Do not redefine the the pinmux configuration for the board, just use
the data directly. No other board will be using those, just the galileo.
Change-Id: If774bc5c4335021ae58a682224f092db23bc9f1b
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Do not have priority per IP, use one config instead.
Change-Id: Ieb2923d4749a294e2a1c677d47d56a14cee3f36d
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Currently, the /CS pin is deasserted by _spi_config_cs() and
the pinmux driver sets it as an input afterwards. Later, setting
the /CS pin to an output via pinmux_dev asserts it.
Setting the SPI port 1 pins in the pinmux driver saves a few lines
of code. Moving the SPI init after pinmux init keeps the /CS pin as
configured by the SPI driver.
Change-Id: I4c587ba0a6983cd89dfb5ecedb2914335e86313b
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
If an external PCIe card inserted into Galileo board, the
devices I/O addresses may differ from the preconfigured ones.
For this reason PCI enumeration needs to be enabled.
Change-Id: I54b5ef9149f9eda0a390909a433b0e13a3dd7ecd
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
On Galileo Gen2 board SPI uses GPIO pin for CS.
Thus spi_intel driver must be initialized after gpio_dw,
so it's init level must be more that gpio_dw's one.
Change-Id: If2e5fb1106afe01e5567cf3fe72063bdc94ad3d2
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Most of the SoC and board Kconfig use the same values for
driver initialization priorities. So refactor them, and
discard duplicate ones.
The shared IRQ init priority was changed so that the kernel
default init and device init priorities can be standardized
across all SoC/boards. Same goes for DesignWare SPI driver.
This also changes the UART_CONSOLE_PRIORITY and
IPM_CONSOLE_PRIORITY to UART_CONSOLE_INIT_PRIORITY and
IPM_CONSOLE_INIT_PRIORITY, to standardize across all drivers.
Note that this does not take away the ability to override
those values. This just provides reasonable defaults such
that there is virtually no need to override.
Change-Id: Ibbd95d802c637df06f9a2fd48763ee1e6f4ff627
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The pinmux base address and number of pins are now defined in SoC or board
header files instead of specifying them in kconfig. This is because
the pinmux ties directly to the SoC (or board expanders) so the base
address and number of pins do not need to be configurable in kconfig.
Change-Id: Ib6090d7d022b491f3fe8f522858281504c6302bb
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds conditions to the default values for device init priorities,
and make them follow the dependencies on the config options. This cleans
up the resulting .config a bit, making it easier to read.
Change-Id: Ib05806ac6108d465ffe245142ecca7a51be6df22
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Anas Nashif