Add board configuration, dts and pinmux, based on
arm/stm32f4_disco and arm/nucleo_f411re boards.
Error free tests are executed on eval board with the following
sample applications:
- hello_world
- blinky-sample
- button-sample
- console_echo_sample
- console_getchar_sample
Signed-off-by: Jose F. Fernandez <jffernandez@fenix-es.com>
Replacing the default paging scheme from 32-bit paging to
PAE paging in QEMU.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
We shouldn't select BOARD_DEPRECATED but set a string with the release
version that the board will get removed in.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replacing the default paging scheme from 32-bit paging to
PAE paging in QEMU.
JIRA:ZEP-2511
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Page Address Extension(PAE) page tables make use of NXE bit in
EFER register.
This patch enables the capability needed to set this bit.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
nucleo_f030r8 fails in CI because applications need
more RAM.
Reduce kernel memory used by stacks and ISR vector table.
Fixes#3923
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The original developer no longer has a working board and isn't
interested in maintaining support for the board. Mark the board
deprecated for now and see if anyone wants to pick it up, otherwise will
remove it in a future release.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Match change we made to how I2C is enabled for other stm32 platforms:
Right now we allow for the I2C subsystem to be built without any drivers
enabled that utilize it. When we added support for the new STM32 I2C
driver we forced the I2C driver to be enabled if the I2C subsystem was
enabled. While this makes a reasonable amount of sense, it breaks
current assumptions for various testcases that we need to cleanup.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IAMCU variant does not need to be the default, this calling
convention was to support the discontinued Quark platforms.
qemu_x86 and qemu_x86_nommu now are set as default.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This will run all tests with the memory management unit disabled.
This means no hardware-based stack protection or user threads.
qemu_x86_iamcu now runs with all MMU features enabled.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch adds support for TI Simplelink MSP-EXP432P401R-LAUNCHXL
development board based on Cortex M4 family
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set Vendor and Product ID originally present in the firmware.
Implemented USB function is the same: CDC ACM serial port.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Clean up & rework JTAG documentation for ESP-32 boards to provide full
commands and clarify gotchas.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This requires openocd version 0.10 or later.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@linaro.org>
The EFM32 Wonder Gecko Starter Kit contains sensors and
peripherals demonstarting the usage of the EFM32WG MCU
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Supports both master and slave mode, standard and fast modes,
configurable timeouts, and a few other tunable settings.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
ESP-IDF is in constant development and it's likely that files Zephyr
depends on will be moved, removed, or renamed. Make a note that an
older version of ESP-IDF should be used instead.
Closes#1538.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Instead of having a board-specific config for this adc test, enable the
required battery-sense circuit by default at the board level when the
adc driver is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Move all QEMU related defines to the boards and cleanup xtensa platforms
which were marked to be QEMU capable by mistake.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
xtensa uses more stack than other arches, enable the sentinel since we
don't currently have HW-assisted stack checking on this arch.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Default configuration for USART1 (Console output) on board
stm32f3_disco was set on PA9/PA10, which matches Rev-A/B
configuration. Though, on more recent configuration of the
board (Rev-C onward). USART1 is mapped to PC4/PC5.
This configuration has the benefit to support VCP, hence it
is chosen to be set by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable BlueNRJ chip on disco_l475_iot1 board.
Communication with SoC, is done over SPI(3). Hence this
commit enables SPI3 on SoC and configure BT_SPI IRQ,
RESET and CS pins.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add board configuration, dts and pinmux based on both
stm32f469i_disco board and nucleo_f412zg board
Signed-off-by: Massimiliano Cialdi <massimiliano.cialdi@powersoft.it>
Move all STM32 based board pinmux files into the board dirs so we are
consistent across all the STM32 platforms/boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added some clarification on flashing instructions for CC3220SF, in
support of customer issue.
Jira: ZEP-2581
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
The zedboard_pulpino has a small amount of flash so we should have that
in the yaml for any tests thats might filter on code size footprint.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch add device tree support for develoement board of
quark_se_c1000. Previously pushed patch was flashing binary
at wrong address because of which UART was not working
Jira:ZEP-2459
test
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
BLE is the only networking interface on 96b_carbon, so if
CONFIG_NETWORKING is set, automatically use 6lowpan/BLE link
layer. This will allow to make networking apps work "out of the
box" on 96b_carbon, similar to e.g. qemu_x86 (which automatically
uses SLIP) or frdm_k64f (which automatically uses Ethernet).
This also enables NET_L2_BT_ZEP1656, because most 6LoWPAN/BLE samples
in Zephyr currently use that option, and it is required to achieve
working 6LoWPAN/BLE with Linux kernels currently widely accessible
to the end users. E.g. the latest Ubuntu LTS release, 16.04, ships
with 4.4 kernel, and can be upgraded with a special effort to HWE
kernel which is currently at 4.10. NET_L2_BT_ZEP1656 is needed for
both these kernels.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Anas Nashif